EN 62035:2014

SLOVENSKI STANDARD
01-maj-2015
1DGRPHãþD
SIST EN 62035:2000
SIST EN 62035:2000/A1:2004
SIST EN 62035:2000/A2:2013
5D]HOHNWULOQHVLMDONHUD]HQIOXRUHVFHQþQLKVLMDON9DUQRVWQHVSHFLILNDFLMH,(&
VSUHPHQMHQ
Discharge lamps (excluding fluorescent lamps) - Safety specifications (IEC 62035:2014,
modified)
Entladungslampen (ausgenommen Leuchtstofflampen) - Sicherheitsanforderungen
Lampes à décharge (à l'exclusion des lampes à fluorescence) - Prescriptions de sécurité
Ta slovenski standard je istoveten z: EN 62035:2014
ICS:
29.140.30 )OXRUHVFHQþQHVLMDONH6LMDONH Fluorescent lamps.
Discharge lamps
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 62035
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2014
ICS 29.140.30 Supersedes EN 62035:2000
English Version
Discharge lamps (excluding fluorescent lamps) - Safety
specifications
(IEC 62035:2014 , modified)
Lampes à décharge (à l'exclusion des lampes à Entladungslampen (ausgenommen Leuchtstofflampen) -
fluorescence) - Prescriptions de sécurité Sicherheitsanforderungen
(CEI 62035:2014 , modifiée) (IEC 62035:2014 , modifiziert)
This European Standard was approved by CENELEC on 2014-09-15. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62035:2014 E
Foreword
This document (EN 62035:2014) consists of the text of IEC 62035:2014 prepared by SC 34A "Lamps",
of IEC/TC 34 "Lamps and related equipment", together with the common modifications prepared by
CLC/TC 34A "Lamps".
The following dates are fixed:
(dop) 2015-09-15
• latest date by which this document has to be implemented
at national level by publication of an identical
national standard or by endorsement
(dow) 2017-09-15
• latest date by which the national standards conflicting
with this document have to be withdrawn

This document supersedes EN 62035:2000.
Photobiological safety requirements are taken care of on basis of the risk group concept of EN 62471
and the technical report IEC/TR 62778 on blue light hazard. This has consequences for terms,
marking, structure of 4.6, and introduction of a new symbol “Caution, do not stare at light source”.
Special attention is given to blue light hazard.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment
Designed for Use within Certain Voltage Limits (LVD - 2006/95/EC).

- 3 - EN 62035:2014
Endorsement notice
The text of the International Standard IEC 62035:2014 was approved by CENELEC as a European
Standard with agreed common modifications.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60432-1 NOTE  Harmonized as EN 60432-1.
IEC 60927 NOTE  Harmonized as EN 60927.
IEC 60598-1 NOTE  Harmonized as EN 60598-1.
IEC 61347-2-9 NOTE  Harmonized as EN 61347-2-9.
COMMON MODIFICATIONS
Delete all references to E26 and E39 lamp caps in the following clauses and figures:
Annex A Data sheet references of IEC 60061 (Table A.1)
Annex B Torsion test values (Table B.2)
Annex C Torsion test holders (Figure C.1)
Annex F Maximum lamp cap temperatures (Table F.1)

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60050 -  International Electrotechnical Vocabulary - -
(IEV)
IEC 60061-1 -  Lamp caps and holders together with EN 60061-1 -
gauges for the control of interchangeability
and safety -
Part 1: Lamp caps
IEC 60061-2 -  Lamp caps and holders together with EN 60061-2 -
gauges for the control of interchangeability
and safety -
Part 2: Lampholders
IEC 60061-3 -  Lamp caps and holders together with EN 60061-3 -
gauges for the control of interchangeability
and safety -
Part 3: Gauges
IEC 60061-4 -  Lamp caps and holders together with EN 60061-4 -
gauges for the control of interchangeability
and safety -
Part 4: Guidelines and general information
IEC 60155 -  Glow-starters for fluorescent lamps EN 60155 -
IEC 60662 -  High pressure sodium vapour lamps - EN 60662 -
Performance specifications
IEC 60695-2-10 2000 Fire hazard testing - EN 60695-2-10 2001
Part 2-10: Glowing/hot-wire based test
methods - Glow-wire apparatus and
common test procedure
IEC 60923 - Auxiliaries for lamps - Ballasts for EN 60923 -
discharge lamps (excluding tubular
fluorescent lamps) - Performance
requirements
IEC 61167 -  Metal halide lamps - Performance EN 61167 -
specification
IEC 61347-2-1 -  Lamp controlgear - EN 61347-2-1 -
Part 2-1: Particular requirements for
starting devices (other than glow starters)

- 5 - EN 62035:2014
Publication Year Title EN/HD Year
IEC/TR 62778 - Application of IEC 62471 for the - -
assessment of blue light hazard to light
sources and luminaires
ISO 4046-4 2002 Paper, board, pulps and related terms - - -
Vocabulary -
Part 4: Paper and board grades and
converted products
IEC 62035 ®
Edition 2.0 2014-04
INTERNATIONAL
STANDARD
Discharge lamps (excluding fluorescent lamps) – Safety specifications

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
X
ICS 29.140.30 ISBN 978-2-8322-1516-6

– 2 – IEC 62035:2014  IEC:2014
CONTENTS
FOREWORD . 5
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
4 General safety requirements . 10
4.1 General . 10
4.2 Marking . 10
4.2.1 Lamp marking . 10
4.2.2 Additional information to be provided . 11
4.3 Mechanical requirements . 11
4.3.1 Requirements for caps . 11
4.3.2 Construction and assembly . 12
Electrical requirements . 13
4.4
4.4.1 Parts which can become accidentally live . 13
4.4.2 Insulation resistance . 13
4.4.3 Electric strength . 13
4.5 Thermal requirements . 14
4.5.1 General . 14
4.5.2 Resistance to heat . 14
4.5.3 Resistance to abnormal heat and fire . 15
4.6 Photobiological requirements . 15
4.6.1 UV Hazard . 15
4.6.2 Blue light hazard . 16
4.6.3 IR hazard . 16
Particular safety requirements . 17
5.1 High-pressure sodium vapour lamps . 17
5.2 Metal halide lamps . 17
5.2.1 General . 17
5.2.2 Marking . 17
5.2.3 Containment . 17
6 Information for luminaire design. 17
7 Assessment . 17
7.1 General . 17
7.2 Assessment of whole production by means of manufacturer’s records . 18
7.2.1 General . 18
7.2.2 Assessment of manufacturer’s records for particular tests . 19
7.2.3 Sampling procedures for the whole production testing . 19
7.3 Assessment of batches . 23
7.3.1 Sampling for batch testing . 23
7.3.2 Number of lamps in batch sample . 23
7.3.3 Sequence of the tests . 23
7.3.4 Rejection conditions for large batches (>500 lamps) . 23
7.3.5 Rejection conditions for small batches (≤500 lamps) . 24
Annex A (normative)  List of lamp caps and gauges . 26
Annex B (normative) Pull and torsion test values . 27

IEC 62035:2014  IEC:2014 – 3 –
Annex C (normative)  Torsion test holders . 28
Annex D (normative) Information for thermal tests . 30
Annex E (normative) Measurement of pulse height for lamps with internal starting
device . 31
E.1 Introduction . 31
E.2 Test circuit . 31
E.2.1 Test circuit and key .
...