EN 62952-1:2016

SLOVENSKI STANDARD
01-september-2017
9LULQDSDMDQMDEUH]åLþQHNRPXQLNDFLMVNHQDSUDYHGHO6SORãQH]DKWHYH]D
QDSDMDOQHPRGXOH,(&
Power sources for a wireless communication device - Part 1: General requirements of
power modules (IEC 62952-1:2016)
Energiequellen für ein Funkkommunikationsgerät - Teil 1: Allgemeine Anforderungen an
Energiemodule (IEC 62952-1:2016)
Sources d'énergie pour un appareil de communication sans fil - Partie 1: Exigences
générales relatives aux modules d'alimentation (IEC 62952-1:2016)
Ta slovenski standard je istoveten z: EN 62952-1:2016
ICS:
29.220.10 3ULPDUQLþOHQLLQEDWHULMH Primary cells and batteries
33.040.40 Podatkovna komunikacijska Data communication
omrežja networks
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 62952-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2016
ICS 29.220.10; 33.040.40
English Version
Power sources for a wireless communication device - Part 1:
General requirements of power modules
(IEC 62952-1:2016)
Sources d'énergie pour un appareil de communication sans Energiequellen für ein Funkkommunikationsgerät - Teil 1:
fil - Partie 1: Exigences générales relatives aux modules Allgemeine Anforderungen an Energiemodule
d'alimentation (IEC 62952-1:2016)
(IEC 62952-1:2016)
This European Standard was approved by CENELEC on 2016-11-09. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62952-1:2016 E
European foreword
The text of document 65B/1053/FDIS, future edition 1 of IEC 62952-1, prepared by SC 65B
“Measurement and control devices” of IEC/TC 65 “Industrial process measurement, control and
automation" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be (dop) 2017-08-09
implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2019-11-09
• latest date by which the national
standards conflicting with the
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 62952-1:2016 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60086-2 NOTE Harmonized as EN 60086-2.

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant

EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60079-0 (mod) 2011 Explosive atmospheres -- Part 0: EN 60079-0 2012
Equipment - General requirements
- -  + A11 2013
IEC 60079-11 2011 Explosive atmospheres -- Part 11: EN 60079-11 2012
Equipment protection by intrinsic safety "i"
IEC 60086-1 -  Primary batteries - Part 1: General EN 60086-1 -
IEC 60654-3 -  Operating conditions for industrial-process EN 60654-3 -
measurement and control equipment --
Part 3: Mechanical influences
IEC 60721-3-4 1995 Classification of environmental conditions - EN 60721-3-4 1995
- Part 3: Classification of groups of
environmental parameters and their
severities -- Section 4: Stationary use at
non-weatherprotected locations
IEC 61326 series Electrical equipment for measurement, - series
control and laboratory use - EMC
requirements
IEC 62952-2 2016 Power sources for a wireless - -
communication device - Part 2: profile for
power modules with batteriess
IEC 62952-3 -  Power sources for a wireless - -
communication device - Part 3: Energy
harvesting specification
IEC 62952-1 ®
Edition 1.0 2016-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Power sources for a wireless communication device –

Part 1: General requirements of power modules

Sources d’énergie pour un appareil de communication sans fil –

Partie 1: Exigences générales relatives aux modules d'alimentation

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.220.10; 33.040.40 ISBN 978-2-8322-3638-3

– 2 – IEC 62952-1:2016  IEC 2016
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references. 6
3 Terms, definitions, abbreviated terms, acronyms and conventions . 7
3.1 Terms and definitions . 7
3.2 Abbreviated terms and acronyms . 7
3.3 Convention for capitalizations . 8
4 General requirements . 8
4.1 General . 8
4.2 Compliance . 9
4.3 Design . 10
4.4 Logistics . 10
4.4.1 Storage and marking . 10
4.4.2 Maintenance . 10
4.4.3 Transportation in a plant . 10
4.4.4 Disposal . 10
4.5 Protection for explosive atmospheres . 10
4.5.1 General . 10
4.5.2 Transportation and replacement . 10
4.5.3 Battery requirements . 11
4.5.4 Temperature . 11
4.5.5 Air pressure . 11
4.6 Harsh environment . 11
4.6.1 General . 11
4.6.2 Vibration and shock . 11
4.6.3 Humidity . 11
4.6.4 Temperature . 12
4.6.5 Corrosive environment . 12
4.6.6 Air pressure . 12
4.7 Interchangeability . 12
4.7.1 General . 12
4.7.2 Electrical interface . 12
4.7.3 Mechanical interface . 13
4.8 Electrical parameters . 13
Bibliography . 14

Figure 1 – Various power sources applicable for a wireless communication device . 8

Table 1 ‒ Example of an implementation conformance statement . 9

IEC 62952-1:2016  IEC 2016 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
POWER SOURCES FOR A WIRELESS COMMUNICATION DEVICE –

Part 1: General requirements of power modules

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoe
...