iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 61557-6:1998

(Main)

Electrical safety in low voltage distribution systems up to 1 kV a.c. and 1,5 kV d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 6: Residual current devices (RCD) in TT, TN and IT systems

Electrical safety in low voltage distribution systems up to 1 kV a.c. and 1,5 kV d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 6: Residual current devices (RCD) in TT, TN and IT systems

Specifies requirements for measuring equipment applied to the testing of the effectiveness of protective measures by regular disconnections of residual current protective devices (RCD) in TT and TN systems.

Elektrische Sicherheit in Niederspannungsnetzen bis AC 1 kV und DC 1,5 kV - Geräte zum Prüfen, Messen oder Überwachen von Schutzmaßnahmen - Teil 6: Fehlerstrom-Schutzeinrichtungen (RCD) in TT-, TN- und IT-Netzen

Sécurité électrique dans les réseaux de distribution basse tension de 1 kV c.a. et 1,5 kV c.c. - Dispositifs de contrôle, de mesure ou de surveillance de mesures de protection - Partie 6: Dispositifs différentiels résiduels (DDR) dans les réseaux TT, TN et IT

Définit les prescriptins applicables aux appareils de mesure destinés à contrôler l'efficacité des mesures de protection lors d'une coupure par les dispositifs différentiels résiduels (DDR) dans les réseaux TT et TN.

Električna varnost v nizkonapetostnih razdelilnih sistemih za izmenične napetosti do 1 kV in enosmerne napetosti do 1,5 kV– Oprema za preskušanje, merjenje ali nadzorovanje zaščitnih ukrepov – 6. del: Naprave na preostali (residualni) tok v sistemih TT, NT in IT (IEC 61557-6:1997, spremenjen)

General Information

Status
Withdrawn
Publication Date
08-Jun-1998
Withdrawal Date
31-Dec-2000
ICS
17.220.20 - Measurement of electrical and magnetic quantities
29.080.01 - Electrical insulation in general
29.240.01 - Power transmission and distribution networks in general
Technical Committee
CLC/SR 85 - Measuring equipment for electrical and electromagnetic quantities
Drafting Committee
IEC/TC 85 - IEC_TC_85
Parallel Committee
IEC/TC 85 - IEC_TC_85
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-Oct-2010
Completion Date
01-Oct-2010
Directive
2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)
73/23/EEC - Electrical equipment designed for use within certain voltage limits
Ref Project
SIST EN 61557-6:1999 - Electrical safety in low voltage distribution systems up to 1 kV a.c. and 1,5 kV d.c. - Equipment for testing, measuring or monitoring of protective measures -- Part 6: Residual current devices (RCD) in TT, TN and IT systems

Relations

Replaced By
EN 61557-6:2007 - Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 6: Effectiveness of residual current devices (RCD) in TT, TN and IT systems
Effective Date
28-Jan-2023

Buy Standard

EN 61557-6:1999EN 61557-6:1999
PreviousNext
Standard
EN 61557-6:1999
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-julij-1999
(OHNWULþQDYDUQRVWYQL]NRQDSHWRVWQLKUD]GHOLOQLKVLVWHPLK]DL]PHQLþQHQDSHWRVWL
GRN9LQHQRVPHUQHQDSHWRVWLGRN9±2SUHPD]DSUHVNXãDQMHPHUMHQMHDOL
QDG]RURYDQMH]DãþLWQLKXNUHSRY±GHO1DSUDYHQDSUHRVWDOL UHVLGXDOQL WRNY
VLVWHPLK7717LQ,7 ,(&VSUHPHQMHQ
Electrical safety in low voltage distribution systems up to 1 kV a.c. and 1,5 kV d.c. -
Equipment for testing, measuring or monitoring of protective measures -- Part 6:
Residual current devices (RCD) in TT, TN and IT systems
Elektrische Sicherheit in Niederspannungsnetzen bis AC 1 kV und DC 1,5 kV - Geräte
zum Prüfen, Messen oder Überwachen von Schutzmaßnahmen -- Teil 6: Fehlerstrom-
Schutzeinrichtungen (RCD) in TT-, TN- und IT-Netzen
Sécurité électrique dans les réseaux de distribution basse tension de 1 kV c.a. et 1,5 kV
c.c. - Dispositifs de contrôle, de mesure ou de surveillance de mesures de protection --
Partie 6: Dispositifs différentiels résiduels (DDR) dans les réseaux TT, TN et IT
Ta slovenski standard je istoveten z: EN 61557-6:1998
ICS:
17.220.20 0HUMHQMHHOHNWULþQLKLQ Measurement of electrical
PDJQHWQLKYHOLþLQ and magnetic quantities
29.080.01 (OHNWULþQDL]RODFLMDQD Electrical insulation in
VSORãQR general
29.240.01 2PUHåMD]DSUHQRVLQ Power transmission and
GLVWULEXFLMRHOHNWULþQHHQHUJL
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 61557-7:2022/A1:2023(Amendment)
Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 7: Phase sequence
SIST EN IEC 61557-7:2022/A1:2024

2022-06-02: CLC/TC 85X made a decision to temporarily remove the link, meanwhile working on the harmonziation issue via another amendment togther with CLC/TC 65X

  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61557-12:2022/AC:2022-09(Corrigendum)
Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 12: Power metering and monitoring devices (PMD)
SIST EN IEC 61557-12:2022/AC:2022

IEC Corrected Version

  • Corrigendum
    4 pages
    French language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61557-12:2022/A1:2022/AC:2022-09(Corrigendum)
Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 12: Power metering and monitoring devices (PMD)
SIST EN IEC 61557-12:2022/A1:2022/AC:2022

IEC Corrected Version

  • Corrigendum
    4 pages
    French language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61557-7:2022(Main)
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 7: Phase sequence
SIST EN IEC 61557-7:2022

IEC 61557-7:2019 is available as IEC 61557-7:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61557-7:2019 specifies the requirements applicable to measuring equipment for testing the phase sequence in three-phase distribution systems. Indication of the phase sequence can be mechanical, visual and/or audible. This document does not apply to additional measurements for other quantities. It does not apply to monitoring relays. IEC 61557-7:2019 cancels and replaces the second edition published in 2007. This edition constitutes a technical revision. This edition includes the following changes with respect to the previous edition: a) alignment of the structure with that of the whole IEC 61557 series; b) updated requirements in 4.3 in accordance with new editions of IEC 61010-1 and IEC 61010-031; c) the information on markings was extended; d) the information on the operating instructions was extended; e) complement to the information on the testing of leads; f) test leads for insulated conductors were introduced; g) Annex B was added with information on phase sequence tests and indications.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61557-3:2022(Main)
Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 3: Loop impedance
SIST EN IEC 61557-3:2022

IEC 61557-3:2019 is available as IEC 61557-3:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61557-3:2019 specifies the requirements applicable to equipment for measuring the loop impedance between a line conductor and protective conductor; between a line conductor and neutral; or between two line conductors by using the voltage drop when the circuit under test is loaded. IEC 61557-3:2019 cancels and replaces the second edition published in 2007. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) addition of equirements as regards the measurement category; b) addition of new requirements for operating instructions; c) alignment of the structure with that of the whole IEC 61557 series.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61557-12:2022(Main)
Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 12: Power metering and monitoring devices (PMD)
SIST EN IEC 61557-12:2022

IEC 61557-12:2018 is available as IEC 61557-12:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61557-12:2018 specifies requirements for power metering and monitoring devices (PMD) that measure and monitor the electrical quantities within electrical distribution systems, and optionally other external signals. These requirements also define the performance in single- and three-phase AC or DC systems having rated voltages up to 1 000 V AC or up to 1 500 V DC. These devices are fixed or portable. They are intended to be used indoors and/or outdoors. Power metering and monitoring devices (PMD), as defined in this document, give additional safety information, which aids the verification of the installation and enhances the performance of the distribution systems. The power metering and monitoring devices (PMD) for electrical parameters described in this document are used for general industrial and commercial applications. This document does not address functional safety and cyber security aspects. This document is not applicable for: – electricity metering equipment that complies with IEC 62053-21, IEC 62053-22, IEC 62053-23 and IEC 62053-24. Nevertheless, uncertainties defined in this document for active and reactive energy measurement are derived from those defined in IEC 62053 (all parts); – the measurement and monitoring of electrical parameters defined in IEC 61557-2 to IEC 61557-9 and IEC 61557-13 or in IEC 62020; – power quality instrument (PQI) according IEC 62586 (all parts); – devices covered by IEC 60051 (all parts) (direct acting analogue electrical measuring instrument). IEC 61557-12:2018 cancels and replaces the first edition published in 2007. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) PMD-A has been withdrawn due the fact these devices are now mainly covered by the IEC 62586 series of standards. b) Three categories of PMD have been created with a list of minimum required functions for each category. c) Added a new Annex A explaining the different applications linked to the relevant standards and devices, and another new Annex C about the power factor conventions.

  • Standard
    106 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61557-12:2022/A1:2022(Amendment)
Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 12: Power metering and monitoring devices (PMD)
SIST EN IEC 61557-12:2022/A1:2022

This part of IEC 61557 specifies requirements for power metering and monitoring devices (PMD) that measure and monitor the electrical quantities within electrical distribution systems, and optionally other external signals. These requirements also defin the performance of PMD in single- and three-phace AC or DC systems having rated voltages up to 1000 V AC or up to 1500 V DC. These devices are fixed or portable. They are intended to be used indoors and/or outdoors. Power metering and monitoring devices (PMD), as defined in this document, give additional safety information, which aids the verification of the installation and enhances the performance of the distribution systems. Additionally, this document specifies requirements for measurement functions dedicated to metering and monitoring of electrical parameters called power metering and monitoring function (PMF) which can be embedded in equipment (EMPF) that is not classified as PMD and for which the main function is not power metering and monitoring. Requirements for power metering and monitoring function (PMF) and additional requirements for equipments embedding power metering and monitoring function (EPMF) are described in Annex H. The power metering and monitoring devices (PMD) for electrical parameters described in this document are used for general industrial and commercial applications. This document does not address functional safety and cyber security aspects. This document is not applicable to: - electricity metering equipment that complies with IEC 62053-21, IEC 62053-22, IEC 62053-23 and IEC 62053-24. Nevertheless, uncertainties defined in this document for active and reactive energy measurement are derived from those defined in IEC 62053 (all parts); - the measurement and monitoring of electrical parameters defined in IEC 61557-2 to IEC 61557-9 and IEC 61557-13 or in IEC 62020; - power quality instrument (PQI) according IEC 62586 (all parts); - devices covered by IEC 60051 (all parts) (direct acting analogue electrical measuring instrument). Note 1 Generally such types of devices are used in the following applications or for the following general needs: - energy management inside the installation, such as facilitating the implementation of documents such as ISO 50001 and IEC 60364-8-1; - monitoring and/or measurement of electrical parameters; - measurement and/or monitoring of the quality of energy inside commercial/industrial installations. Note 2 A measuring and monitoring device of electrical parameters usually consists of several functional modules. All or some of the functional modules are combined in one device. Examples of fuctnional modules are: - measurement and monitoring of several electrical parameters simultaneously; - energy measurement and/or monitoring, as well as sometimes compliance with aspects of building regulations; - alarms functions; - demand side quality (current and voltage harmonics, over/under voltages, voltage dips and swells, etc.). Note 3 PMD are historically called power meter, power monitor, power monitor device, power energy monitoring device, power analyser, multifunction meter, measuring multifunction equipment, energe meters. Note 4 Metering, measuring and monitoring applications are explained in Annex A.

  • Amendment
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61557-17:2021(Main)
Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 17: Non-contact AC voltage indicators
SIST EN IEC 61557-17:2022

This part of IEC 61557 defines minimum performance requirements for non-contact AC voltage indicators to reduce the risk of electric shock for the testing person and bystanders caused by the wrong interpretation of the indication. Products designed and manufactured in accordance with this document are for use by (electrically) skilled persons only. Non-contact AC voltage indicators are not designed for testing the absence of the operating voltage.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61557-6:2021(Main)
Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 6: Effectiveness of residual current devices (RCD) in TT, TN and IT systems
SIST EN IEC 61557-6:2022

IEC 61557-6:2019 is available as IEC 61557-6:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61557-6:2019 specifies the requirements applicable to measuring equipment for testing the effectiveness of protective measures of residual current devices (RCD) installed in TT, TN and IT systems. It is not the purpose of this document to verify the RCD according to their product standards. IEC 61557-6:2019 cancels and replaces the second edition published in 2007. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) addition of requirements for testing a new type of RCD; b) addition of requirements for type B RCDs (former Annex B); c) addition of new Annex B on recommended tripping times; d) alignment of the structure with that of the whole IEC 61557 series.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61557-2:2021(Main)
Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V DC - Equipment for testing, measuring or monitoring of protective measures - Part 2: Insulation resistance
SIST EN IEC 61557-2:2022

IEC 61557-2:2019 is available as IEC 61557-2:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61557-2:2019 specifies the requirements applicable to equipment for measuring the insulation resistance of equipment and installations in the de-energized state IEC 61557-2:2019 cancels and replaces the second edition published in 2007. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) addition of requirements as regards measurement category; b) addition of new requirements for operating instructions; c) alignment of the structure with that of the the whole IEC 61557 series.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day