EN 1119:2009

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoff-Rohrleitungssysteme - Verbindungen für Rohre und Formstücke aus glasfaserverstärkten duroplastischen Kunststoffen (GFK) - Prüfverfahren zur Dichtheit und Widerstandsfähigkeit gegen Beschädigung von nicht druckbeständigen flexiblen Verbindungen mit elastomeren DichtungselementenSystèmes de canalisations plastiques - Assemblages pour tubes et raccords en plastique thermodurcissable renforcé de verre (PRV) - Méthodes d'essai d'étanchéité et de résistance à l'endommagement des assemblages flexibles non résistants à la poussée avec bagues d'étanchéité en élastomèrePlastics piping systems - Joints for glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods for leaktightness and resistance to damage of non-thrust resistant flexible joints with elastomeric sealing elements83.120Reinforced plastics23.040.60Prirobnice, oglavki in spojni elementiFlanges, couplings and jointsICS:Ta slovenski standard je istoveten z:EN 1119:2009SIST EN 1119:2009en,fr,de01-junij-2009SIST EN 1119:2009SLOVENSKI
STANDARDSIST EN 1119:19971DGRPHãþD

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1119March 2009ICS 23.040.60Supersedes EN 1119:1996
English VersionPlastics piping systems - Joints for glass-reinforcedthermosetting plastics (GRP) pipes and fittings - Test methodsfor leaktightness and resistance to damage of non-thrustresistant flexible joints with elastomeric sealing elementsSystèmes de canalisations plastiques - Assemblages pourtubes et raccords en plastique thermodurcissable renforcéde verre (PRV) - Méthodes d'essai d'étanchéité et derésistance à l'endommagement des assemblages flexiblesnon résistants à la poussée avec bagues d'étanchéité enélastomèreKunststoff-Rohrleitungssysteme - Verbindungen für Rohreund Formstücke aus glasfaserverstärkten duroplastischenKunststoffen (GFK) - Prüfverfahren zur Dichtheit undWiderstandsfähigkeit gegen Beschädigung von nichtdruckbeständigen flexiblen Verbindungen mit elastomerenDichtungselementenThis European Standard was approved by CEN on 8 February 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1119:2009: ESIST EN 1119:2009

Between each test condition (see Table 1 and Table 2) the joint is inspected for signs of damage. NOTE It is assumed that the following test parameters are set by the standard making reference to this European Standard: a)
the nominal size of the components to be connected by the joint (see 4.1); b)
the pressure class of the components (see 4.1); c)
the total effective length, L, of the test piece (see 4.1); d)
the number of test pieces (see 4.2); e)
if applicable, the conditioning to be applied (see Clause 5); f)
the test temperature (see Clause 6); g)
sequence of testing, if appropriate (see 7.1); h)
the joint positions (see Table 1 and Table 2); i)
the draw, angular deflection (see 7.2.3) and the force F (see 7.3.5); j)
the permissible change in negative pressure (see 7.5.4). SIST EN 1119:2009

support R [see Figure 1b) and Figure 2b)], positioned at least 500 mm from the spigot end of the pipe at the
...