EN ISO 23411:2021

SLOVENSKI STANDARD
01-marec-2021
Nadomešča:
SIST EN ISO 15652:2017
SIST EN ISO 8848:2017
SIST EN ISO 9775:2017
Mala plovila - Krmila (ISO 23411:2020)
Small craft - Steering wheels (ISO 23411:2020)
Kleine Wasserfahrzeuge - Steuerräder (ISO 23411:2020)
Petits navires - Barres à roues (ISO 23411:2020)
Ta slovenski standard je istoveten z: EN ISO 23411:2021
ICS:
47.020.70 Navigacijska in krmilna Navigation and control
oprema equipment
47.080 Čolni Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 23411
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2021
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 15652:2017, EN ISO 8848:2017,
EN ISO 9775:2017
English Version
Small craft - Steering wheels (ISO 23411:2020)
Petits navires - Barres à roues (ISO 23411:2020) Kleine Wasserfahrzeuge - Steuerräder (ISO
23411:2020)
This European Standard was approved by CEN on 30 July 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 23411:2021 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered . 4

European foreword
This document (EN ISO 23411:2021) has been prepared by Technical Committee ISO/TC 188 "Small
craft" in collaboration with CCMC.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2021, and conflicting national standards shall be
withdrawn at the latest by July 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15652:2017, EN ISO 8848:2017 and EN ISO 9775:2017.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 23411:2020 has been approved by CEN as EN ISO 23411:2021 without any modification.

Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered
This European Standard has been prepared under a Commission’s standardization request M/542/C
(2015) 8736 final to provide one voluntary means of conforming to essential requirements of Directive
2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and
Directive 2013/53/EU
Essential Requirements of Clause(s)/sub-clause(s) Remarks/Notes
Directive 2013/53/EU of this EN
Annex I.A.5.4.1 – Steering system, Clauses 1 - 6 This scope of this standard
General addresses the design, and testing
of steering wheels for
recreational craft as defined in
Directive 2013/53/EU, Article
3(2) only.
Annex II, Components of Clauses 1 - 6 This scope of this standard
watercraft (3) - Steering wheels, addresses the design, and testing
steering mechanisms and cable of steering wheels supplied as
assemblies. components for recreational craft
as defined in Directive
2013/53/EU, Article 3(2) only.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 23411
First edition
2020-12
Small craft — Steering wheels
Petits navires — Barres à roues
Reference number
ISO 23411:2020(E)
©
ISO 2020
ISO 23411:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

ISO 23411:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 2
5 Tests . 5
5.1 Conditioning . 5
5.2 Mechanical tests . 5
5.3 Impact load tests . 6
6 Fatigue tests . 8
Bibliography .10
ISO 23411:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 188, Small craft, in collaboration with
the European Committee for Standardization (CEN) Technical Committee CEN/TC 464, Small craft, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This first edition of ISO 23411, together with ISO 8848:2020, cancels and replaces ISO 8848:1990,
ISO 9775:1990 and ISO 15652:2003, which have been technically revised.
The main changes compared to the previous editions are as follows:
— the steering wheel requirements from ISO 8848:1990, ISO 9775:1990 and ISO 15652:2003 have
been consolidated into this document;
— the requirements have been updated to meet current industry practices.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved

ISO 23411:2020(E)
Introduction
Previously, steering wheels were addressed in ISO 8848:1990, ISO 9775:1990 and ISO 15652:2003. A
review of the steering standards for a merge project found that updates were needed for consistency
and to meet current industry practices. This document thus provides a consistent approach for the
design and testing of steering wheels for small craft.
Steering wheel size and application was considered in the development of this document for small craft
under foreseeable operating conditions. It is recognized that high speed craft experience additional
impact loads and these are addressed in the document.
INTERNATIONAL STANDARD ISO 23411:2020(E)
Small craft — Steering wheels
1 Scope
This document specifies design and testing requirements for steering wheels for small craft.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments
...