Reinforced plastics composites - Specifications for pultruded profiles - Part 2: Methods of test and general requirements

This Part 2 of ENxxxx defines the general requirements applicable to the specification of all types of pultruded profiles falling within the scope of this specification as defined in Part 1 of the standard. This Part 2 of ENxxxx describes the procedures to be followed in the preparation of test specimens for the determination of mechanical properties required for the designation in Part 1 and the technical specification in Part 3. This Part 2  of ENxxxx also defines the test methods to be used to determine both the designated and the specified properties given in Parts 1 & 3 respectively.

Verstärkte Kunststoffverbundwerkstoffe - Spezifikationen für pultrudierte Profile - Teil 2: Prüfverfahren und allgemeine Anforderungen

1.1   Der vorliegende Teil 2 von EN 13706 legt die allgemeinen Anforderungen fest, die auf die Spezifikation von sämtlichen Arten pultrudierter Profile anwendbar sind, die in den Anwendungsbereich dieser Spezifikation fallen, wie es in Teil 1 von EN 13706 festgelegt ist.
1.2   Der vorliegende Teil 2 von EN 13706 legt die Eigenschaften fest, die bei der Vorbereitung von Probekörpern zur Bestimmung von mechanischen Eigenschaften für die Bezeichnung in Teil 1 und die besonderen Anforderungen in Teil 3 von EN 13706 zu befolgen sind.
1.3   Der vorliegende Teil 2 von EN 13706 legt auch die Prüfverfahren fest, die zur Bestimmung der in den Teilen 1 bzw. 3 von EN 13706 bezeichneten und festgelegten Eigenschaften anzuwenden sind.

Composites en plastiques renforcés - Spécification pour les profilés pultrudés - Partie 2: Méthodes d'essai et exigences générales

1.1   La présente partie 2 de l'EN 13706 spécifie les exigences générales applicables à la spécification de tous les types de profilés pultrudés entrant dans le cadre du domaine d'application de cette spécification, comme défini dans la Partie 1 de l'EN 13706.
1.2   La présente partie de l'EN 13706 spécifie les modes opératoires à suivre pour préparer les éprouvettes utilisées pour déterminer les propriétés mécaniques nécessaires à la désignation définie dans la Partie 1 et à la spécification technique définie dans la Partie 3 de l'EN 13706.
1.3   La présente partie de l'EN 13706 spécifie également les méthodes d'essai à utiliser pour déterminer les propriétés désignées et les propriétés spécifiées indiquées respectivement dans les Parties 1 et 3 de l'EN 13706.

Ojačeni polimerni kompoziti - Specifikacije za pultrudirane profile - 2. del: Preskusne metode in splošne zahteve

General Information

Status
Published
Publication Date
29-Oct-2002
ICS
83.120 - Reinforced plastics
 
83.140.99 - Other rubber and plastics products
Technical Committee
CEN/TC 249 - Plastics
Drafting Committee
CEN/TC 249/SC 2/WG 6 - Pultruded profiles
Current Stage
9093 - Decision to confirm - Review Enquiry
Start Date
03-Dec-2022
Completion Date
14-Apr-2025
Ref Project
SIST EN 13706-2:2003 - Reinforced plastics composites - Specifications for pultruded profiles - Part 2: Methods of test and general requirements

Overview

EN 13706-2:2002 - part of the CEN series on Reinforced plastics composites - Specifications for pultruded profiles - defines the methods of test and general requirements for pultruded composite profiles. It sets out how to prepare test plates and specimens, which test methods to use to determine mechanical properties, and general quality, appearance and labelling requirements that support the product designation (Part 1) and specific requirements (Part 3).

Keywords: EN 13706-2, pultruded profiles, pultrusion, reinforced plastics composites, methods of test, mechanical properties.

Key topics and technical requirements

  • Scope and intent: Applies to all pultruded profiles covered by EN 13706; specifies test procedures for properties used in Parts 1 and 3.
  • Preparation of test plates and specimens:
    • Test plates manufactured per ISO 1268-6 (pultrusion moulding) to simulate production conditions.
    • Minimum flat-strip widths: 50 mm for longitudinal-only properties, 250 mm when transverse properties are required.
    • Specimen cutting methods allowed: milling, sawing (diamond or hard-metal blade), laser or water-jet, or block milling from pre-cut packs.
  • Sampling and quality documentation:
    • Manufacturer testing within a recognised quality-control scheme.
    • Certificate of Conformity (when required) to meet EN 10204 formats and list obligatory properties plus any optional tests agreed with the customer.
  • General requirements:
    • Appearance and visual acceptance levels (Annex A: visual defects such as blisters, cracks, delamination - defined descriptions and acceptance criteria).
    • Dimensional tolerances (Annex B) and workmanship standards (Annex C).
    • Labelling requirements: designation code, product type, section dimensions, quantity/length, gross/net weight.
  • Specified test methods:
    • Full-section effective flexural modulus - Annex D.
    • Pin bearing strength - Annex E.
    • Referenced coupon tests: EN ISO 527-4 (tension), EN ISO 14125 (flexure), EN ISO 14130 (short-beam shear), plus other normative references.

Applications and who uses it

EN 13706-2 is used by:

  • Pultrusion manufacturers to qualify and document product mechanical properties and ensure consistent production.
  • Design engineers and specifiers requiring validated property data for structural or non‑structural composite components.
  • Quality managers and testing laboratories for preparing specimens, performing tests, and resolving quality disputes.
  • Procurement and compliance teams who require certified conformity documentation aligned to CEN standards.

Practical benefits: consistent test methods, repeatable property data for design, clear acceptance criteria for appearance and dimensions, and an agreed framework for supplier–customer testing and certification.

Related standards

  • EN 13706-1 (Designation)
  • EN 13706-3 (Specific requirements)
  • Normative references cited: EN ISO 527-4, EN ISO 14125, EN ISO 14130, ISO 1268-6, EN 10204, ISO 5893, ISO 1172, ISO 1183, ISO 11359, ISO 15310.

Use EN 13706-2 when you need standardized, industry-accepted test procedures and general requirements for evaluating and documenting pultruded composite profiles.

Frequently Asked Questions

EN 13706-2:2002 is a standard published by the European Committee for Standardization (CEN). Its full title is "Reinforced plastics composites - Specifications for pultruded profiles - Part 2: Methods of test and general requirements". This standard covers: This Part 2 of ENxxxx defines the general requirements applicable to the specification of all types of pultruded profiles falling within the scope of this specification as defined in Part 1 of the standard. This Part 2 of ENxxxx describes the procedures to be followed in the preparation of test specimens for the determination of mechanical properties required for the designation in Part 1 and the technical specification in Part 3. This Part 2 of ENxxxx also defines the test methods to be used to determine both the designated and the specified properties given in Parts 1 & 3 respectively.

This Part 2 of ENxxxx defines the general requirements applicable to the specification of all types of pultruded profiles falling within the scope of this specification as defined in Part 1 of the standard. This Part 2 of ENxxxx describes the procedures to be followed in the preparation of test specimens for the determination of mechanical properties required for the designation in Part 1 and the technical specification in Part 3. This Part 2 of ENxxxx also defines the test methods to be used to determine both the designated and the specified properties given in Parts 1 & 3 respectively.

EN 13706-2:2002 is classified under the following ICS (International Classification for Standards) categories: 83.120 - Reinforced plastics; 83.140.99 - Other rubber and plastics products. The ICS classification helps identify the subject area and facilitates finding related standards.

You can purchase EN 13706-2:2002 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of CEN standards.

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Verstärkte Kunststoffverbundwerkstoffe - Spezifikationen für pultrudierte Profile - Teil 2: Prüfverfahren und allgemeine AnforderungenComposites en plastiques renforcés - Spécification pour les profilés pultrudés - Partie 2: Méthodes d'essai et exigences généralesReinforced plastics composites - Specifications for pultruded profiles - Part 2: Methods of test and general requirements83.120Reinforced plasticsICS:Ta slovenski standard je istoveten z:EN 13706-2:2002SIST EN 13706-2:2003en01-maj-2003SIST EN 13706-2:2003SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13706-2October 2002ICS 83.120; 83.140.99English versionReinforced plastics composites - Specifications for pultrudedprofiles - Part 2: Methods of test and general requirementsComposites en plastique renforcé - Spécification pour lesprofilés pultrudés - Partie 2: Méthodes d'essai et exigencesgénéralesVerstärkte Kunststoffverbundwerkstoffe - Spezifikationenfür pultrudierte Profile - Teil 2: Prüfverfahren undallgemeine AnforderungenThis European Standard was approved by CEN on 16 September 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13706-2:2002 ESIST EN 13706-2:2003

Visual Defects: Descriptions and Acceptance Levels (see also annex C -Workmanship).9Annex B (normative)
Dimensional tolerances for pultruded profiles.12Annex C (normative)
Workmanship.14Annex D (normative)
Determination of effective flexural modulus.16Annex E (normative)
Determination of the pin bearing strength.21Annex F (informative)
Recommended test methods for particular requirements.26Annex G (informative)
Determination of flexural, shear and torsional stiffness properties.29Bibliography.40SIST EN 13706-2:2003
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

Loading comments...

この記事は、EN 13706-2:2002について説明しています。この規格は、強化プラスチック複合材料、特に引抜成形プロファイルに対するものです。この規格のPart 2では、規格の範囲内のすべての引抜成形プロファイルの仕様に適用される一般的な要件を定義しています。Part 2では、Part 1で定義された指定およびPart 3で指定された技術仕様に必要な機械的特性を決定するための試験試験体の準備手順について説明しています。また、Part 2では、規格のPart 1およびPart 3でそれぞれ指定された特性を決定するために使用される試験方法を定義しています。

The article discusses EN 13706-2:2002, which is a standard for reinforced plastics composites, specifically for pultruded profiles. Part 2 of this standard outlines the general requirements for the specification of all pultruded profiles within the scope of the standard. It explains the procedures for preparing test specimens to determine mechanical properties required for designation and technical specifications. Additionally, Part 2 defines the test methods to determine both designated and specified properties outlined in Parts 1 and 3 of the standard, respectively.

이 기사는 EN 13706-2:2002라는 강화 플라스틱 복합재에 대한 표준에 대해서 설명하고 있습니다. 이 표준의 Part 2는 표준의 범위 내에 속하는 모든 풀트루딩 프로파일에 대한 사양을 정의하는 일반 요구사항을 설명합니다. Part 2는 Part 1에 정의된 분류 및 Part 3에 기술된 기술 사양을 위한 기계적 특성을 결정하기 위한 시험 시험체 준비 절차에 대해 설명합니다. 또한, Part 2는 표준의 Part 1 및 Part 3에 각각 명시된 지정 및 사양된 특성을 결정하기 위해 사용되는 시험 방법을 정의합니다.