EN 13001-2:2004/A1:2006
(Amendment)Cranes - General design - Part 2: Load actions
Cranes - General design - Part 2: Load actions
This documentis to be used together with Part 2 and Part 3, and as such, they specify general conditions, requirements and methods to prevent mechanical hazards of cranes by design and theoretical verification. Part 3 is only at pre-drafting stage; the use of Parts 1 and 2 is not conditional to the publication of Part 3.
NOTE Specific requirements for particular types of crane are given in the appropriate European Standard for the particular crane type.
The following is a list of significant hazardous situations and hazardous events that could result in risks to persons during normal use and foreseeable misuse. Clause 4 of this standard is necessary to reduce or eliminate the risks associated with the following hazards:
a) rigid body instability of the crane or its parts (tilting, shifting);
b) exceeding the limits of strength (yield, ultimate, fatigue);
c) elastic instability of the crane or its parts (buckling, bulging);
d) exceeding temperature limits of material or components;
e) exceeding the deformation limits.
This document is applicable to cranes which are manufactured after the date of approval by CEN of this standard and serves as reference base for the European Standards for particular crane types.
Krane - Konstruktion allgemein - Teil 2: Lasteinwirkungen
Appareils de levage à charge suspendue - Conception générale - Partie 2: Effets de charge
Dvigala (žerjavi) – Konstrukcija, splošno – 2. del: Bremenski učinki
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2007
'YLJDOD åHUMDYL ±.RQVWUXNFLMDVSORãQR±GHO %UHPHQVNLXþLQNL
Cranes - General design - Part 2: Load actions
Krane - Konstruktion allgemein - Teil 2: Lasteinwirkungen
Appareils de levage a charge suspendue - Conception générale - Partie 2: Effets de
charge
Ta slovenski standard je istoveten z: EN 13001-2:2004/A1:2006
ICS:
53.020.20 Dvigala Cranes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 13001-2:2004/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2006
ICS 53.020.20
English Version
Cranes - General design - Part 2: Load actions
Appareils de levage à charge suspendue - Conception Krane - Konstruktion allgemein - Teil 2: Lasteinwirkungen
générale - Partie 2: Effets de charge
This amendment A1 modifies the European Standard EN 13001-2:2004; it was approved by CEN on 18 September 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13001-2:2004/A1:2006: E
worldwide for CEN national Members.
Contents Page
Foreword.3
4.2 Loads .4
4.3 Load combinations.4
4.3.3 Mass distribution classes MDC1 and MDC2 .4
4.3.4 Partial safety factors for the mass of the crane .5
Foreword
This document (EN 13001-2:2004/A1:2006) has been prepared by Technical Committee CEN/TC 147
“Cranes - Safety”, the secretariat of which is held by BSI.
This Amendment to the European Standard EN 13001-2:2004 shall be given the status of a national standard,
either by publication of an identical text or by endorsement, at the latest by April 2007, and conflicting national
standards shall be withdrawn at the latest by April 2007.
This draft amendment covers the necessary additional precautions by replacing the relevant existing text of
EN 13001-2:2004.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.