EN ISO 22637:2019

SLOVENSKI STANDARD
01-oktober-2019
Nadomešča:
SIST EN 13415:2010
Lepila - Preskusna metoda za lepila za talne obloge - Določanje električne
upornosti lepilnih filmov in kompozitov (ISO 22637:2019)
Adhesives - Test of adhesive for floor covering - Determination of the electrical resistance
of adhesive films and composites (ISO 22637:2019)
Klebstoffe - Prüfung von Klebstoffen für Bodenbeläge - Bestimmung des elektrischen
Widerstandes von Klebstoff-Filmen und Verbunden (ISO 22637:2019)
Adhésifs - Essai des adhésifs pour revêtements de sol - Détermination de la résistance
électrique des composites et films d'adhésif (ISO 22637:2019)
Ta slovenski standard je istoveten z: EN ISO 22637:2019
ICS:
83.180 Lepila Adhesives
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 22637
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2019
EUROPÄISCHE NORM
ICS 83.180 Supersedes EN 13415:2010
English Version
Adhesives - Test of adhesive for floor covering -
Determination of the electrical resistance of adhesive films
and composites (ISO 22637:2019)
Adhésifs - Essai des adhésifs pour revêtements de sol - Klebstoffe - Prüfung von Klebstoffen für Bodenbeläge -
Détermination de la résistance électrique des Bestimmung des elektrischen Widerstandes von
composites et films d'adhésif (ISO 22637:2019) Klebstoff-Filmen und Verbunden (ISO 22637:2019)
This European Standard was approved by CEN on 8 September 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22637:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 22637:2019) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 193 “Adhesives” the secretariat of which is held by
UNE.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2020, and conflicting national standards shall
be withdrawn at the latest by January 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13415:2010.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 22637:2019 has been approved by CEN as EN ISO 22637:2019 without any modification.

INTERNATIONAL ISO
STANDARD 22637
First edition
2019-07
Adhesives — Test of adhesive for floor
covering — Determination of the
electrical resistance of adhesive films
and composites
Adhésifs — Essai des adhésifs pour revêtements de sol —
Détermination de la résistance électrique des composites et films
d'adhésif
Reference number
ISO 22637:2019(E)
©
ISO 2019
ISO 22637:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

ISO 22637:2019(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3  Terms and definitions . 1
4  Apparatus and materials. 2
5 Preparation of test specimens . 4
5.1 Preparation of test specimens for determination of adhesive resistance, R . 4
5.2 Preparation of test specimens for determination of vertical resistance of composite, R . 4
6 Storing the specimens . 5
6.1 Storing the specimens for determination of adhesive resistance, R . 5
6.2 Storing the specimens for determination of vertical resistance of composite R . 5
7 Test procedure . 6
7.1 General . 6
7.2 Adhesive resistances, R . 6
7.3 Vertical resistance of composite, R . 6
8 Test report . 6
ISO 22637:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11,
Products.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved

INTERNATIONAL STANDARD ISO 22637:2019(E)
Adhesives — Test of adhesive for floor covering —
Determination of the electrical resistance of adhesive films
and composites
SAFETY STATEMENT — Persons using this document should be familiar with the normal
laboratory practice, if applicable. This document does not purport to address all of the
safety problems, if any, associated with its use. It is the responsibility of the user to establish
appropriate safety and health practices.
ENVIRONMENTAL STATEMENT — It is understood that some of the material permitted in
this document may have negative environmental impact. As technological advantages lead to
acceptable alternatives for these materials, they will be eliminated from this document to the
extent possible. At the end of the test, the user of the document should take care to carry out an
appropriate disposal of the wastes.
1 Scope
This document specifies a test method to measure the electrical resistance as a material physical
parameter of an adhesive film and composites of floor covering material and adhesive film. The
electrical resistance is reciprocal to the electrical conductivity. This laboratory method does not take
account of all influences which can occur in practice.
This method applies to the determination of the electrical resistance of adhesive films on glass and of
composites of floor coverings, adhesively bonded to a fibre cement substrate R and R (see Clause 3).
4 5
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 472, Plastics — Vocabulary
ISO 554, Standard atmospheres for conditioning and/or testing — Specifications
ISO 9142, Adhesives — Guide to the selection of standard laboratory ageing conditions for testing
bonded joints
ISO 15605, Adhesives — Sampling
EN 1067, Adhesives — Examination and preparation of samples for testing
EN 1081:2018, Resilient floor coverings — Determination of the electrical resistance
3  Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 472 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https: //www .iso .org/obp
— IEC Electropedia: available at http: //www .electropedia .org/
ISO 22637:2019(E)
3.1
vertical resistance of floor covering
R
electrical resistance, measured at an unbounded floor covering sample between the tripod electrode
on the surface of the floor covering and a second electrode on the opposite underside
3.2
resistance to ground
R
electrical resistance, measured at a bonded floor covering between a tripod electrode on the surface of
the floor covering and ground
3.3
point to point resistance
R
electrical resistance measured on the surface of a bonded floor covering between two tripod electrodes
in a
...