EN 1777:2004/prA1

SLOVENSKI STANDARD
01-september-2008
+LGUDYOLþQHSORãþDGL+3V]DJDVLOVNHLQUHãHYDOQHHQRWH9DUQRVWQH]DKWHYHLQ
SUHVNXãDQMH
Hydraulic platforms (HPs) for fire fighting and rescue services - Safety requirements and
testing
Hubrettungsfahrzeuge für Feuerwehren und Rettungsdienste, Hubarbeitsbühnen (HABn)
- Sicherheitstechnische Anforderungen und Prüfung
Bras Élevateur Aérien (BEA) des services d'incendie et de secours - Prescriptions de
sécurité et essais
Ta slovenski standard je istoveten z: EN 1777:2004/prA1
ICS:
13.220.10 Gašenje požara Fire-fighting
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 1777:2004
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
July 2008
ICS 13.220.10
English Version
Hydraulic platforms (HPs) for fire fighting and rescue services -
Safety requirements and testing
Bras Élevateur Aérien (BEA) des services d'incendie et de Hubrettungsfahrzeuge für Feuerwehren und
secours - Prescriptions de sécurité et essais Rettungsdienste, Hubarbeitsbühnen (HABn) -
Sicherheitstechnische Anforderungen und Prüfung
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 192.
This draft amendment A1, if approved, will modify the European Standard EN 1777:2004. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1777:2004/prA1:2008: E
worldwide for CEN national Members.

Contents Page
Foreword.3
th
1 Modification to the Foreword, 4 paragraph .4
2 Modification to 5.3, Chassis and stabilizers .4
3 Modification to 5.5.2.1.2, Wire rope drive systems .4
4 Modification to 5.5.3.1.2, Chain drive systems .5
5 Modification to 7.1.1, General.5
6 Modification to 7.1.2, Operating instructions, which shall give detailed information
necessary for safe use. e.g.5
7 Modification to 7.1.4, Information on commissioning .6
8 Modification to 7.1.7, Maintenance information for use by trained personnel (see
introduction) e.g.6
9 Modification to 7.2.2 .6
10 Modification to Figure 13 .7
11 Addition of new Annex ZB .7

Foreword
This document (EN 1777:2004/prA1:2008) has been prepared by Technical Committee CEN/TC 192 “Fire
service equipment”, the secretariat of which is held by BSI.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.
The reason for amending the published standard EN 1777:2004 are as follows:
The revision of the EC-Machinery Directive 98/37/EC into 2006/42/EC requires the modification of published
European Standards cited in the Official Journal of the European Communities under that Directive. If no
amendment is made by the committee experts, then the standard would be updated with an Annex Z stating
that it does NOT meet the requirements of 2006/42/EC. This would result in the standard being removed from
the Official Journal and becoming a non-harmonized standard.
To keep the published standard EN 1777:2004 as a harmonized standard it was carefully checked against the
new EC-Machinery Directive 2006/42/EC and it was established that EN 1777:2004 meets the Essential
Health and Safety Requirements (EHSR) of the new EC-Machinery Directive 2006/42/EC in nearly all
requirements of the standard. Only a few requirements were established for a necessary amendment.
CEN/TC 192 has therefore decided to use the Type 2 amendment track, which is a 5 months UAP
amendment with the addition of a new Annex ZB, only few technical update as well as minor editorial
changes.
th
1 Modification to the Foreword, 4 paragraph
th
Replace the existing 4 Paragraph with the following:
"For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.".
2 Modification to 5.3, Chassis and stabilizers
Add the following new subclause 5.3.26:
"5.3.26 An electrically conducting connection between the HP and the bearing surface shall be ensured
during operation. For HPs which are constructed for operation with stabilizers, the jacking devices shall
...