EN 13458-2:2002
(Main)Cryogenic vessels - Static vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing
Cryogenic vessels - Static vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing
This standard is applicable to the design, fabrication, inspection and testing of static vacuum insulated cryogenic vessels designed for a maximum allowable pressure of more than 0,5 bar. This standard applies to static vacuum insulated cryogenic vessels for fluids as specified in WI 00268006 and is not applicable to vessels designed for toxic fluids. For static vacuum insulated cryogenic vessels designed for a maximum allowable pressure of not more than 0,5 bar this standard may be used as a guide.
Kryo-Behälter - Ortsfeste vakuum-isolierte Behälter - Teil 2: Bemessung, Herstellung und Prüfung
Diese Europäische Norm gilt für die Bemessung, Herstellung und Prüfung von ortsfesten, vakuum-isolierten Kryo-Behältern, die für einen höchstzulässigen Betriebsdruck von über 0,5 bar bemessen sind.
Diese Norm gilt für ortsfeste, vakuum-isolierte Kryo-Behälter für Fluide, die in prEN 13458-1 festgelegt sind, und sie gilt nicht für giftige Fluide.
Für ortsfeste vakuum-isolierte Kryo-Behälter mit einem höchstzulässigen Betriebsdruck von weniger als 0,5 bar kann diese Norm als eine Richtlinie angewendet werden.
Récipients cryogéniques - Récipients fixes isolés sous vide - Partie 2: Conception, fabrication, inspection et essais
La présente Norme européenne spécifie des exigences de conception, fabrication, contrôle et essais des récipients cryogéniques fixes, isolés sous vide, conçus pour une pression maximale admissible supérieure à 0,5 bar.
La présente Norme européenne s'applique aux récipients cryogéniques fixes, isolés sous vide, pour les fluides, tels que spécifiés dans l'EN 13458-1 et ne s'applique pas aux récipients conçus pour contenir des fluides toxiques.
Pour les récipients cryogéniques fixes, isolés sous vide, conçus pour une pression maximale admissible inférieure ou égale à 0,5 bar, la présente Norme européenne peut servir de guide.
Kriogene posode - Stabilne, vakuumsko izolirane posode - 2. del: Načrtovanje, izdelava, nadzor in preskus
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cryogenic vessels - Static vacuum insulated vessels - Part 2: Design, fabrication, inspection and testing1DþUWRYDQMHRécipients cryogéniques - Récipients fixes isolés sous vide - Partie 2: Conception, fabrication, inspection et essaisKryo-Behälter - Ortsfeste vakuum-isolierte Behälter - Teil 2: Bemessung, Herstellung und PrüfungTa slovenski standard je istoveten z:EN 13458-2:2002SIST EN 13458-2:2003en23.020.40ICS:SLOVENSKI
STANDARDSIST EN 13458-2:200301-december-2003
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13458-2November 2002ICS 23.020.40English versionCryogenic vessels - Static vacuum insulated vessels - Part 2:Design, fabrication, inspection and testingRécipients cryogéniques - Récipients fixes isolés sous vide- Partie 2: Conception, fabrication, inspection et essaisKryo-Behälter - Ortsfeste vakuum-isolierte Behälter - Teil 2:Bemessung, Herstellung und PrüfungThis European Standard was approved by CEN on 12 August 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13458-2:2002 E
Elastic stress analysis.68Annex B (normative)
Additional requirements for 9 % Ni steel.77Annex C (informative)
Pressure strengthening of vessels from austenitic stainless steels.79Annex D (normative)
Pressure limiting systems.90Annex E (normative)
Further use of the material cold properties to resist pressure loads.91Annex F (informative)
Specific weld details.95Annex G (normative)
Additional requirements for flammable fluids.99Annex H (informative)
Non-design requirements for flammable fluids.100Annex I (normative)
Outer jacket relief devices.101Annex J (informative)
Increased material property for austenitic stainless steel.103Annex K (normative)
Base materials.104Annex L (informative)
Other materials.105Annex ZA (informative)
Clauses of this European Standard addressing essential requirements or other provisionsof EU directives.106Bibliography.107
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.