Ferronickel - Specification and delivery requirements (ISO 6501:2020)

This document specifies the technical delivery requirements for the various forms of ferronickel (ingots, pieces and shot) usually supplied for steel making and foundry use.

Ferronickel - Spezifikation und Lieferbedingungen (ISO 6501:2020)

Dieses Dokument legt die technischen Lieferbedingungen für die verschiedenen Lieferformen von Ferro-nickel fest (Barren, Stücke und Schrot), wie sie üblicherweise bei der Stahlerzeugung und in Gießereien verwendet werden.

Ferro-nickel - Spécifications et conditions de livraison (ISO 6501:2020)

Le présent document spécifie les conditions techniques de livraison des diverses formes de ferro-nickel (lingots, morceaux et grenailles) habituellement fournies pour utilisation en aciérie et en fonderie.

Feronikelj - Specifikacija in zahteve pri dobavi (ISO 6501:2020)

General Information

Status
Published
Publication Date
16-Jun-2020
Withdrawal Date
30-Dec-2020
Technical Committee
Drafting Committee
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
17-Jun-2020
Completion Date
17-Jun-2020

Relations

Buy Standard

Standard
EN ISO 6501:2020
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-oktober-2020
Nadomešča:
SIST EN 26501:2009
Feronikelj - Specifikacija in zahteve pri dobavi (ISO 6501:2020)
Ferronickel - Specification and delivery requirements (ISO 6501:2020)
Ferronickel - Spezifikation und Lieferbedingungen (ISO 6501:2020)
Ferro-nickel - Spécifications et conditions de livraison (ISO 6501:2020)
Ta slovenski standard je istoveten z: EN ISO 6501:2020
ICS:
77.100 Železove zlitine Ferroalloys
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 6501
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2020
EUROPÄISCHE NORM
ICS 77.100 Supersedes EN 26501:1992
English Version
Ferronickel - Specification and delivery requirements (ISO
6501:2020)
Ferro-nickel - Spécifications et conditions de livraison Ferronickel - Spezifikation und Lieferbedingungen (ISO
(ISO 6501:2020) 6501:2020)
This European Standard was approved by CEN on 4 April 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6501:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 6501:2020) has been prepared by Technical Committee ISO/TC 155 "Nickel and
nickel alloys" in collaboration with CCMC.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2020, and conflicting national standards
shall be withdrawn at the latest by December 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 26501:1992.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 6501:2020 has been approved by CEN as EN ISO 6501:2020 without any modification.

INTERNATIONAL ISO
STANDARD 6501
Second edition
2020-06
Ferronickel — Specification and
delivery requirements
Ferro-nickel — Spécifications et conditions de livraison
Reference number
ISO 6501:2020(E)
©
ISO 2020
ISO 6501:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

ISO 6501:2020(E)
Contents  Page
Foreword .iv
1 Scope . 1
2  Normative references . 1
3  Terms and definitions . 1
4  Information for ordering . 2
5  Requirements . 2
5.1 Chemical composition . 2
5.2 Form of delivery and formation of lots . 3
5.2.1 General. 3
5.2.2 Ferronickel in ingots . 3
5.2.3 Ferronickel in pieces . . 3
5.2.4 Ferronickel in the form of shot . 4
5.3 Contamination . 4
6  Control . 4
6.1 General . 4
6.2 Sampling for analysis . 4
6.3 Analysis. 4
6.3.1 Ferronickel furnished with analysis certificate . 4
6.3.2 Ferronickel settled with exchange analysis . 4
6.4 Procedures in case of dispute . 5
6.4.1 General. 5
6.4.2 Contradictory procedure . 5
6.4.3 Arbitration procedure . 5
Annex A (informative) Examples of ferronickel classification . 6
ISO 6501:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see
www .iso .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 155, Nickel and nickel alloys, in
collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/
TC SS M14, Nickel, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 6501:1988), which has been technically
revised. The main changes compared with the previous edition are as follows:
— expressions such as “agreement between parties” have been reduced or eliminated (because if a
standard or part of it is to be agreed, there is no need for that International Standard);
— the ferronickel delivery market requirements have been updated;
— FeNi classification has been clarified according chemical composition and combination of Ni content
(Table 1) and impurities (Table 2); this was previously in one table.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved

INTERNATIONAL STANDARD ISO 6501:2020(E)
Ferronickel — Specification and delivery requirements
1 Scope
This document specifies the technical delivery requirements for the various forms of ferronickel
(ingots, pieces and shot) usually supplied for steel making and foundry use.
2  Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 6352, Ferronickel — Determination of nickel content — Dimethylglyoxime gravimetric method
ISO 8049, Ferronickel shot — Sampling for analysis
ISO 8050, Ferronickel ingots or pieces — Sampling for analysis
ISO 14284, Steel and iron — Sampling and preparation of samples for the determination of chemical
composition
3  Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
3.1
ferronickel
master alloy of iron and nickel having a nickel content equal to or greater than a mass fraction of 15 %
and less than a mass fraction of 80 %, obtained from oxide ores or other nickel-bearing materials
3.2
K
number that represents the l
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.