EN 14035-24:2004

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Fireworks - Part 24: Novelty matches - Specification and test methodsOgnjemet – 24. del: Vžigalice s pokom – Specifikacija in preskusne metodeArtifices de divertissement - Partie 24: Allumettes détonantes - Spécifications et méthodes d'essaiFeuerwerkskörper - Teil 24: Scherzzündholzer - Anforderungen und PrüfverfahrenTa slovenski standard je istoveten z:EN 14035-24:2004SIST EN 14035-24:2004en71.100.30ICS:SLOVENSKI
STANDARDSIST EN 14035-24:200401-november-2004

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14035-24August 2004ICS 71.100.30English versionFireworks - Part 24: Novelty matches - Specification and testmethodsArtifices de divertissement - Partie 24: Allumettesdétonantes - Spécifications et méthodes d'essaiFeuerwerkskörper - Scherzzündholz - Teil 24: Anforderungen und PrüfverfahrenThis European Standard was approved by CEN on 14 June 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14035-24:2004: E

This European Standard is one of a series of standards as listed below. EN 14035-1, Fireworks - Part 1: Terminology. EN 14035-2, Fireworks - Part 2: Categorisation. EN 14035-3, Fireworks - Part 3: Aerial wheels - Specification and test methods. EN 14035-4, Fireworks - Part 4: Bangers and banger batteries - Specification and test methods. prEN 14035-5, Fireworks - Part 5: Batteries and combinations - Specification and test methods. EN 14035-6, Fireworks - Part 6: Bengal flames - Specification and test methods. EN 14035-7, Fireworks - Part 7: Bengal matches - Specification and test methods. EN 14035-8, Fireworks - Part 8: Bengal sticks - Specification and test methods. EN 14035-9, Fireworks - Part 9: Crackling granules - Specification and test methods. EN 14035-10, Fireworks - Part 10: Double bangers - Specification and test methods. EN 14035-12, Fireworks - Part 12: Flash bangers and flash banger batteries - Specification and test methods. EN 14035-13, Fireworks - Part 13: Flash pellets - Specification and test methods. EN 14035-15, Fireworks - Part 15: Fountains - Specification and test methods. EN 14035-17, Fireworks - Part 17: Ground spinners - Specification and test methods. prEN 14035-18, Fireworks - Part 18: Hand-held fountains - Specification and test methods. EN 14035-19, Fireworks - Part 19: Hand-held sparklers - Specification and test methods. prEN 14035-20, Fireworks - Part 20: Jumping crackers - Specification and test methods. prEN 14035-21, Fireworks - Part 21: Jumping ground spinners - Specification and test methods. EN 14035-22, Fireworks - Part 22: Mines - Specification and test methods. EN 14035-23, Fireworks - Part 23: Non-hand-held sparklers - Specification and test methods.

1 Scope This document specifies requirements for the construction, performance, primary packaging and labelling of novelty matches and the corresponding test methods. It is applicable to fireworks which are classified as novelty match in category 1 in EN 14035-2 and which are contained in a primary pack. It is applicable to novelty matches which contain pyrotechnic report composition that is silver fulminate only. It is not applicable to novelty matches containing pyrotechnic composition that includes any of the following substances: — arsenic or arsenic compounds; — mixtures containing a mass fraction of chlorates greater than 80 %; — mixtures of chlorates with metals; — mixtures of chlorates with red phosphorus; — mixtures of chlorates with potassium hexacyanoferrate(II); — mixtures of chlorates with sulfur; — mixtures of chlorates with sulfides; — lead or lead compounds; — mercury compounds; — white phosphorus; — picrates or picric acid; — potassium chlorate with a mass fraction of bromates greater than 0,15 %; — sulfur with an acidity, expressed in mass fraction of sulphuric acid, greater than 0,002 %; — zirconium with a particle size of less than 40 µm. NOTE In EN 14035-2, novelty matches are classified as follows: — brief description: match with a dot of pyrotechnic composition, designed to be held in the hand; — principal effects: report and/or visual effect. Schemes for type testing of novelty matches and batch testing of novelty matches are specified in annex A and annex B respectively.

EN 14035-1:2003, Fireworks — Part 1: Terminology. EN 14035-2, Fireworks — Part 2: Categorisation. EN 20187, Paper, board and pulps - Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples (ISO 187:1990). EN ISO 536, Paper and board - Determination of grammage (ISO 536:1995). EN ISO 845, Cellular plastics and rubbers — Determination of apparent (bulk) density (ISO 845:1988). EN ISO 868, Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868:2003). EN ISO 2439, Flexible cellular polymeric materials - Determination of hardness (indentation technique) (ISO 2439:1997, including Technical Corrigendum 1:1998). EN ISO 3696, Water for analytical laboratory use, Specification and test methods. ISO 2859-1, Sampling procedures for inspection by attributes — Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection. ISO 3599, Vernier callipers, reading to 0,1 and 0,05 mm. ISO 4793, Laboratory sintered (fritted) filters - Porosity grading, classification and designation. ISO 6344-3, Coated abrasives - Grain size analysis - Part 3: Determination of grain size distribution of microgrits P240 to P2500. ISO 21948, Coated abrasives – Plain sheets. 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 14035-1:2003 apply. 4 Construction 4.1 Means of ignition The means of ignition shall be identified by a friction head. Conformity to this requirement shall be verified by visual examination. 4.2 Attachment of effect charge The attachment of the effect charge to the novelty match shall be secure when tested in accordance with 8.1.
...