EN 1501-1:1998/FprA2

SLOVENSKI STANDARD
01-junij-2009
9R]LOD]D]ELUDQMHRGSDGNRYLQSULSDGDMRþLL]WUHVDOQLNL6SORãQHLQYDUQRVWQH
]DKWHYHGHO9R]LOD]D]ELUDQMHRGSDGNRY]QDNODGDQMHP]DGDM
Refuse collection vehicles and their associated lifting devices - General requirements
and safety requirements - Part 1: Rear-end loaded refuse collection vehicles
Ta slovenski standard je istoveten z: EN 1501-1:1998/FprA2
ICS:
43.160 Vozila za posebne namene Special purpose vehicles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 1501-1:1998
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA2
April 2009
ICS 43.160
English Version
Refuse collection vehicles and their associated lifting devices -
General requirements and safety requirements - Part 1: Rear-
end loaded refuse collection vehicles
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 183.
This draft amendment A2, if approved, will modify the European Standard EN 1501-1:1998. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1501-1:1998/FprA2:2009: E
worldwide for CEN national Members.

Contents Page
Foreword .3
1 Modification to Clause 2 .4
2 Modifications to Clause 6 .4
3 Modification to Clause 7 .5
4 Modification to Annex ZA .6
5 Addition of Annex ZB .6

Foreword
This document (EN 1501-1:1998/FprA2:2009) has been prepared by Technical Committee CEN/TC 183
“Waste management”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.
1 Modification to Clause 2
Delete the following references:
"prEN 31689, Acoustics – Systematic collection and comparison of noise emission data for machinery and
equipment (ISO/DIS 11689:1993)
prEN 32001, Acoustics – Noise emitted by machinery and equipment – Rules for the drafting and presentation
of a noise test code
ISO/DIS 4871, Acoustics – Declaration and verification of noise emitted by machinery and equipment
ISO/TR 11688-1, Acoustics – Recommended practice for the design of low-noise machinery and equipment –
Part 1: Planning".
Add the following reference:
"EN 1501-4:2007, Refuse collection vehicles and their associated lifting devices – General requirements and
safety requirements — Part 4: Noise test code for refuse collection vehicles”.
2 Modifications to Clause 6
Replace 6.10 with the following:
"
6.10 Noise measurement
The noise measurement:
...