Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 4: Pulpers and their loading facilities

This European Standard applies to pulpers and their loading facilities intended for use in paper making and
shall be used together with EN 1034-1:2000. It deals with all significant hazards, hazardous situations and
hazard events relevant to pulpers and their loading facilities, when they are used as intended and under the
conditions foreseen by the manufacturer (see clause 4).
This European Standard is not applicable to pulpers and their loading facilities that have been manufactured
before the date of publication of this standard.

Sicherheit von Maschinen - Sicherheitstechnische Anforderungen an Konstruktion und Bau von Maschinen der Papierherstellung und Ausrüstung - Teil 4: Stofflöser und deren Beschickungseinrichtungen

Diese Europäische Norm gilt für Stofflöser und deren Beschickungseinrichtungen, die zur Verwendung bei der Papierherstellung bestimmt sind, und muss in Verbindung mit EN 1034-1:2000 angewendet werden. Sie behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die auf Stofflöser und deren Beschickungseinrichtungen zutreffen, wenn sie bestimmungsgemäß und entsprechend den vorhersehbaren Bedingungen des Herstellers verwendet werden (siehe Abschnitt 4).
Diese Europäische Norm gilt nicht für Stofflöser und deren Beschickungseinrichtungen, die hergestellt wurden, bevor CEN diese Norm veröffentlichte.

Sécurité des machines - Prescriptions de sécurité pour la conception et la construction de machines de fabrication et de finition du papier - Partie 4: Triturateurs et leurs dispositifs d'alimentation

La présente Norme européenne s’applique aux triturateurs et à leurs systèmes d’alimentation destinés à la
fabrication du papier et doit être utilisée conjointement avec l’EN 1034-1:2000. Elle traite tous les
phénomènes dangereux significatifs, les situations et les événements dangereux engendrés par les
triturateurs et leurs systèmes d’alimentation lorsqu’ils sont utilisés normalement et dans les conditions
prévues par le constructeur (voir Article 4).
La présente Norme européenne n’est pas applicable aux triturateurs et à leurs systèmes d’alimentation qui
ont été fabriqués avant la date de publication de cette norme par le CEN.

Varnost strojev – Varnostne zahteve za načrtovanje in konstrukcijo strojev in opreme za izdelavo papirja – 4. del: Razpuščevalniki in pripadajoče naprave za polnjenje

General Information

Status
Withdrawn
Publication Date
22-Nov-2005
Withdrawal Date
01-Dec-2009
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
02-Dec-2009
Completion Date
02-Dec-2009

Relations

Buy Standard

Standard
EN 1034-4:2006
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.SROQMHQMHSicherheit von Maschinen - Sicherheitstechnische Anforderungen an Konstruktion und Bau von Maschinen der Papierherstellung und Ausrüstung - Teil 4: Stofflöser und deren BeschickungseinrichtungenSécurité des machines - Prescriptions de sécurité pour la conception et la construction de machines de fabrication et de finition du papier - Partie 4: Triturateurs et leurs dispositifs d'alimentationSafety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 4: Pulpers and their loading facilities85.100Oprema za papirno industrijoEquipment for the paper industry21.020Characteristics and design of machines, apparatus, equipment13.110Varnost strojevSafety of machineryICS:Ta slovenski standard je istoveten z:EN 1034-4:2005SIST EN 1034-4:2006en01-julij-2006SIST EN 1034-4:2006SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1034-4November 2005ICS 85.100 English VersionSafety of machinery - Safety requirements for the design andconstruction of paper making and finishing machines - Part 4:Pulpers and their loading facilitiesSécurité des machines - Prescriptions de sécurité pour laconception et la construction de machines de fabrication etde finition du papier - Partie 4: Triturateurs et leursdispositifs d'alimentationSicherheit von Maschinen - SicherheitstechnischeAnforderungen an Konstruktion und Bau von Maschinender Papierherstellung und Ausrüstung - Teil 4: Stofflöserund deren BeschickungseinrichtungenThis European Standard was approved by CEN on 20 October 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2005 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1034-4:2005: ESIST EN 1034-4:2006

Relationship of this European Standard with the Essential Requirements of EU Directive 98/37/EC.18 Bibliography.19
Figures Figure 1 — Pulper with loading facility (example).6 Figure 2 — Drum pulper (example).7 Figure 3 — Protection against falling from a height at discharge openings for waste (recovery stock)11 Figure 4 — Protection against falling from a height on recovery pulper underneath the Pope reel winder.12 SIST EN 1034-4:2006

which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 1034-4:2006

ISO 12100-1.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this European Standard.
For machines that have been designed and built according to the provisions of this type C standard, the following stipulation applies: when provisions of this type C standard are different from those which are stated in type A or B standards or from provisions made in EN 1034-1:2000, the provisions of this type C standard take precedence over the provisions of the other standards. 1 Scope This European Standard applies to pulpers and their loading facilities intended for use in paper making and shall be used together with EN 1034-1:2000. It deals with all significant hazards, hazardous situations and hazard events relevant to pulpers and their loading facilities, when they are used as intended and under the conditions foreseen by the manufacturer (see clause 4). This European Standard is not applicable to pulpers and their loading facilities that have been manufactured before the date of publication of this standard. 2 Normative references The following referenced documents are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN 294:1992, Safety of machinery — Safety distances to prevent danger zones being reached by the upper limbs EN 349:1993, Safety of machinery — Minimum gaps to avoid crushing of parts of the human body
EN 418:1992, Safety of machinery — Emergency stop equipment, functional aspects — Principles for design EN 547 (all Parts), Safety of machinery — Human body measurements EN 617:2001, Continuous handling equipment and systems — Safety and EMC requirements for the storage of bulk goods in silos, bunkers, bins and hoppers EN 618:2002, Continuous handling equipment and systems — Safety and EMC requirements for equipment for mechanical handling of bulk materials except stationary belt conveyors EN 619:2002, Continuous handling equipment and systems — Safety and EMC requirements for equipment for mechanical handling of unit loads EN 620:2002, Continuous handling equipment and systems — Safety and EMC requirements for equipment for stationary belt conveyors for bulk materials EN 626-1:1994, Safety of machinery — Reduction of risk to health from hazardous substances emitted by machinery — Part 1: Principles and specifications for machinery manufacturers SIST EN 1034-4:2006

(IEC 60204-1:1997) EN 61000-6-2:2001, Electromagnetic compatibility (EMC — Generic standard — Part 6-2: Emission standard for industrial environment (IEC 61000-6-2:1999, modified) EN ISO 12100-1:2003, Safety of machinery — Basic concepts — General principles for design — Part 1: Basic terminology, methodology (ISO 12100-1:2003) EN ISO 12100-2:2003, Safety of machinery — Basic concepts — General principles for design — Part 2: Technical principles and specifications (ISO 12100-2:2003) EN 14122-1:2001, Safety of machinery — Permanent means of access to machines and industrial plants — Part 1: Choice of a fixed means of access between two levels (ISO 14122-1:2001) EN 14122-2:2001, Safety of machinery — Permanent means of access to machines and industrial plants — Part 2: Working platforms and gangways (ISO 14122-2:2001) EN 14122-3:2001, Safety of machinery — Permanent means of access to machines and industrial plants — Part 3: Stairways, stepladders and guard-rails (ISO 14122-3:2001)
EN ISO 12100-1:2003 and the following terms and defini
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.