EN 10220:2002

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Nahtlose und geschweißte Stahlrohre - Allgemeine Tabellen für Maße und längenbezogene MasseTubes lisses en acier, soudés et sans soudure - Tableaux généraux des dimensions et des masses linéiquesSeamless and welded steel tubes - Dimensions and masses per unit length23.040.10Železne in jeklene ceviIron and steel pipesICS:Ta slovenski standard je istoveten z:EN 10220:2002SIST EN 10220:2003en01-april-2003SIST EN 10220:2003SLOVENSKI
STANDARDSIST ENV 10220:19971DGRPHãþD

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10220December 2002ICS 23.040.10; 77.140.70English versionSeamless and welded steel tubes - Dimensions and masses perunit lengthTubes lisses en acier, soudés et sans soudure - Tableauxgénéraux des dimensions et des masses linéiquesNahtlose und geschweißte Stahlrohre - AllgemeineTabellen für Maße und längenbezogene MasseThis European Standard was approved by CEN on 16 October 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,
Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10220:2002 ESIST EN 10220:2003

Information on dimensions for steel tubes for special applications can be found in other EuropeanStandards, e.g. prEN 10255, EN 10305 series, EN ISO 11960 and EN ISO 11961, information on dimensions forstainless steel tubes in EN ISO 1127.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and publications are listed hereafter. For datedreferences, subsequent amendments to or revisions of any of these publications apply to this European Standardonly when incorporated in it by amendment or revision. For undated references the latest edition of the publicationreferred to applies (including amendments).prEN 10266, Steel tubes, fittings and structural hollow sections – Symbols and definition of terms for use in productstandards.3 Terms and definitionsFor
the purpose of this European Standard the terms and definitions in prEN 10266 apply.4 Classification of outside diametersThe outside diameters given in Tables 1 and 2 are classified into three series which may be described in thefollowing way:¾ series 1: outside diameters for which all the accessories needed for the construction of piping systems arestandardized;¾ series 2: outside diameters for which not all accessories are standardized;¾ series 3: outside diameters for which very few standardized accessories exist.NOTE 1
It is recommended to select, for tubes intended to be used as components of piping systems, outside diameters fromseries 1 in Table 1. Tubes with outside diameters in accordance with series 2 and 3 may not, or not easily, be available.NOTE 2
Accessories for heavy wall tubes with dimensions in accordance with Table 2 may not be available regardless of theseries in Table 1 to which the relevant outside diameter is allocated.SIST EN 10220:2003

kg/mwhereMis the mass per unit length in kg/m,Dis the specified outside diameter in mm andTis the specified wall thickness in mm.The calculated values may also be applied to tubes with different density values, but have then to be multiplied bya factor of¾ 1,015 for austenitic stainless steel2)¾ 0,985 for ferritic and martensitic stainless steel3) .NOTE
EN 10088-1 provides distinguished density values for various groups of stainless steel grades which may be used forcalculating purposes.6 Dimensions and masses per unit lengthTable 1 gives dimensions consisting of outside diameters D, from 3 series as described in Clause 4, and relatedwall thicknesses T £ 65 mm and the calculated masses per unit length of plain end tube.Table 2 gives dimensions consisting of outside diameters D and related wall thicknesses T from 70 mm to 100 mmand the calculated masses per unit length of plain end tube.
1)This factor is based on a density of 7,85 kg/dm³.2)This factor is based on a density of 7,97 kg/dm³.3)This factor is based on a density of 7,73 kg/dm³.SIST EN 10220:2003
...