iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 12953-13:2012

(Main)

Shell boilers - Part 13: Operating instructions

Shell boilers - Part 13: Operating instructions

This European Standard identifies the requirements for the manufacturer to provide operating instructions for pressure equipment supplied in accordance with EN 12953-1 when placed on the market.
NOTE   Where the equipment or assembly will reach the final user in a Member State which requires translation of operating instructions, manufacturers should be aware of this requirement.

Großwasserraumkessel - Teil 13: Betriebsanleitungen

Diese Europäische Norm enthält die Anforderungen, die der Hersteller beim Erstellen von Betriebsanleitungen für Druckgeräte nach EN 12953 1 zu erfüllen hat, wenn diese in Verkehr gebracht werden.
ANMERKUNG   Bei Lieferung von Druckgeräten oder Baugruppen an einen Endanwender in einem Mitgliedstaat, der eine Übersetzung der Betriebsanleitung fordert, sollten die Hersteller diese Anforderung berücksichtigen.

Chaudières à tubes de fumée - Partie 13: Instructions de service

La présente Norme européenne spécifie les exigences relatives aux instructions de service devant être fournies par le fabricant pour les équipements sous pression réalisés conformément à l’EN 12953-1 lors de leurs mises sur le marché.
NOTE   Lors de la livraison de l’équipement ou de l’assemblage à l’utilisateur final dans un Etat Membre demandant la traduction des instructions de service, il convient que les fabricants soient informés de l’existence de cette exigence.

Mnogovodni kotli - 13. del: Navodila za obratovanje

Ta evropski standard določa zahteve za proizvajalce, da za tlačno opremo, dobavljeno v skladu s standardom EN 12953-1, ob začetku prodaje zagotovijo navodila za obratovanje.

General Information

Status
Published
Publication Date
24-Jan-2012
Withdrawal Date
30-Jul-2012
ICS
27.060.30 - Boilers and heat exchangers
Technical Committee
CEN/TC 269 - Shell and water tube boilers
Drafting Committee
CEN/TC 269/WG 2 - Shell boilers
Current Stage
9092 - Decision on results of review/2YR ENQ - revise - Review Enquiry
Completion Date
28-Apr-2020
Directive
2014/68/EU - Directive 2014/68/EU of the European Parliament and of the Council of 15 May 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of pressure equipment
97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
Mandate
M/071 - Mandate to CEN for standardization in the field of Pressure equipment
Ref Project
SIST EN 12953-13:2012 - Shell boilers - Part 13: Operating instructions

Buy Standard

EN 12953-13:2012EN 12953-13:2012
PreviousNext
Standard
EN 12953-13:2012
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Mnogovodni kotli - 13. del: Navodila za obratovanjeGroßwasserraumkessel - Teil 13: BetriebsanleitungenChaudières à tubes de fumée - Partie 13: Instructions de serviceShell boilers - Part 13: Operating instructions27.060.30Grelniki vode in prenosniki toploteBoilers and heat exchangersICS:Ta slovenski standard je istoveten z:EN 12953-13:2012SIST EN 12953-13:2012en,fr,de01-maj-2012SIST EN 12953-13:2012SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12953-13
January 2012 ICS 27.060.30 English Version
Shell boilers - Part 13: Operating instructions
Chaudières à tubes de fumée - Partie 13: Instructions de service
Großwasserraumkessel - Teil 13: Betriebsanleitungen This European Standard was approved by CEN on 9 December 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12953-13:2012: ESIST EN 12953-13:2012

Relationship between this European Standard and the Essential Requirements of EU Directive 97/23/EC .7Bibliography .8 SIST EN 12953-13:2012
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 12953-5:2020(Main)
Shell boilers - Part 5: Inspection during construction, documentation and marking of pressure parts of the boiler
SIST EN 12953-5:2020

This document specifies requirements for the inspection during and after construction, documentation and marking of shell boilers as defined in EN 12953-1.
NOTE   For other components, such as water tube walls, reference will be made to the EN 12952 series.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard – translation
    35 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12953-4:2018(Main)
Shell boilers - Part 4: Workmanship and construction of pressure parts of the boiler
SIST EN 12953-4:2018

This European Standard specifies requirements for the workmanship and construction of shell boilers as defined in EN 12953-1.
NOTE 1   For other components such as water tube walls, see the EN 12952 series.
NOTE 2   For economizers and superheaters, see EN 12953-4 or EN 12952-5.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12953-3:2016(Main)
Shell boilers - Part 3: Design and calculation for pressure parts
SIST EN 12953-3:2016

This Part of this European Standard specifies requirements for the design and calculation of pressure parts of shell boilers as defined in EN 12953 1.
NOTE   For other components such as economisers, superheaters, tube walls, headers, reference should be made to EN 12952 series.

  • Standard
    109 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12953-1:2012(Main)
Shell boilers - Part 1: General
SIST EN 12953-1:2012

1.1   General
This European Standard applies to shell boilers with volumes in excess of 2 litres for the generation of steam and/or hot water at a maximum allowable pressure greater than 0,5 bar and with a temperature in excess of
110 °C.
The purpose of this European Standard is to ensure that the hazards associated with the operation of shell boilers are reduced to a minimum and that adequate protection is provided to contain the hazards that still prevail when the shell boiler is put into service. This protection will be achieved by the proper application of the design, manufacturing, testing and inspection methods and techniques incorporated in the various parts of this European Standard. Where appropriate, adequate warning of residual hazards and the potential for misuse are given in the training and operating instructions and local to the equipment concerned (see EN 12953-7 and EN 12953-8).
It is the manufacturer's responsibility, in addition to complying with the requirements of this standard, to take into consideration special measures which could be necessary in order to achieve by manufacturing the required level of safety in accordance with the EU Directive 97/23/EC (PED).
NOTE 1   Further requirements relating to operating instructions in prEN 12953-13 and to hazard analysis in
CEN/TS 764-6 should be taken into consideration.
This European Standard specifies requirements for both directly fired and electrically heated boilers including Low Pressure Boilers (LPB, see 3.6) as well as for heat recovery boilers with a gas-side pressure not exceeding 0,5 bar of cylindrical design, constructed from carbon or carbon manganese steels by fusion welding and a design pressure not exceeding 40 bar. The boilers covered by this European Standard are intended for land use for providing steam or hot water (typical examples are shown in Figures 1 to 6).
For Low Pressure Boilers (LPB) less stringent requirements concerning design and calculation are acceptable. Details are defined in the respective clauses.
NOTE 2   For boilers operating at a pressure on the gas-side greater than 0,5 bar the rules of this standard equally apply. However, it is generally considered that additional design analysis, inspection and testing may be necessary.
Where a particular boiler is a combination of shell and water-tube design then the water-tube standard series EN 12952 is used in addition to this European Standard. One such example of this combination is shown in Figure 3.
This European Standard applies to the generator, from the feed-water or water inlet connection to the steam or water outlet connection and to all other connections, including the valves and steam and water fittings. If welded ends are used, the requirements specified herein begin or end at the weld where flanges, if used, would have been fitted.
1.2   Exclusions
This European standard does not apply to the following types of boilers and equipments:
a)   water-tube boilers;
b)   non stationary boilers, e.g. locomotive boilers;
c)   thermal oil boilers;
d)   boilers where the main pressure housing is made of cast material.
e)   pumps, gaskets, etc.
f)   brickwork setting and insulation, etc.
NOTE   Stainless steel boilers are covered by EN 14222.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12953-2:2012(Main)
Shell boilers - Part 2: Materials for pressure parts of boilers and accessories
SIST EN 12953-2:2012

This European Standard specifies the following materials for the pressure bearing parts of shell boilers and equipment of shell boilers (e.g. valves), subjected to internal and external pressure including integral attachments (non pressure bearing parts):
   flat products (plate) and parts formed from flat products (e.g. shell, furnace, dished ends);
   tubes and parts formed from tubes (e.g. bending, elbows, reducers, fittings);
   forgings and cast products ;
   bolting materials;
   welding consumables.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12953-6:2011(Main)
Shell Boilers - Part 6: Requirements for equipment for the boiler
SIST EN 12953-6:2011

This part of this European Standard specifies the minimum requirements for safety related equipment for shell boilers as defined in EN 12953-1, to ensure the boiler operates within the allowable limits (pressure, temperature, etc.) and if the limits are exceeded the energy supply shall be interrupted and locked out without manual (human) intervention at the boiler.
NOTE 1   The maximum time of operation without manual (human) intervention should be defined for each boiler system.
NOTE 2   Annex C (informative) gives recommendations of operation and testing of the boiler system with a maximum time of operation without manual (human) intervention of 72 hours.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12953-9:2007(Main)
Shell boilers - Part 9: Requirements for limiting devices of the boiler and accessories
SIST EN 12953-9:2007

This European Standard specifies requirements for limiters (or limiting devices) which are incorporated into safety systems for shell boilers as defined in EN 12953-1.
A limiter (or limiting device) can be either:
-   a safety accessory as defined in the Pressure Equipment Directive, Article 1, clause 2.1.3, and needs to include the safety logic and final actuator, or
-   one element of a safety system, for example, a self-monitoring water level sensor used as part of a safety accessory as defined in the Pressure Equipment Directive, Article 1, clause 2.1.3. The overall boiler protection function needs to be provided in association with additional safety logic (where appropriate) and a final actuator.
The design requirements and examination of functional capability for the limiters are covered in this European Standard.
For an explanation of the extent of the limiter (or limiting device) see Figure A.1.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12952-14:2004(Main)
Water-tube boilers and auxiliary installations - Part 14: Requirements for flue gas DENOX-systems using liquefied pressurized ammonia and ammonia water solution
SIST EN 12952-14:2004

This draft European Standard covers the safety requirements regarding the storage and use of:
-   liquefied pressurized ammonia for steam boiler plants;
-   liquid ammonia water solution for the reduction of NOx in the flue gas from boiler plants.
Annex A summarizes the operational aspects.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12952-13:2003/A1:2003(Amendment)
Water-tube boilers and auxiliary installations - Part 13: Requirements for flue gas cleaning systems
SIST EN 12952-13:2003/A1:2004

This European Standard applies to the design of equipment for boiler plants to reduce air pollutants in the flue gases.
NOTE   The effects of explosion are not considered in this Part of the is European Standard.

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12953-10:2003(Main)
Shell boilers - Part 10 : Requirements for feedwater and boiler water quality
SIST EN 12953-10:2004

This part of the European Standard applies to all shell boilers as defined in prEN 12953-1 which are heated by combustion of one or more fuels or by hot gases for the generation of steam and/or hot water. This European Standard applies to those components between the feedwater inlet and the steam outlet of the steam generator. The quality of the steam produced is outside the scope of this standard.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard – translation
    15 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day