EN 10246-17:2000
(Main)Non-destructive testing of steel tubes - Part 17: Ultrasonic testing of tube ends of seamless and welded steel tubes for the detection of laminar imperfections
Non-destructive testing of steel tubes - Part 17: Ultrasonic testing of tube ends of seamless and welded steel tubes for the detection of laminar imperfections
This Part of EN 10246 specifies requirements for the full peripheral ultrasonic testing of the ends of seamless and welded tubes for the detection of laminar imperfections. The standard specifies acceptance levels and calibration procedures. This Part of EN 10246 is applicable to the inspection of welded tubes with an outside diameter greater than 30 mm. No lower limit of wall thickness is specified but see note in 3.1. European Standard EN 10246 "Non destructive testing of steel tubes" comprises the parts shown in Annex A.
Zerstörungsfreie Prüfung von Stahlrohren - Teil 17: Ultraschallprüfung der Rohrenden nahtloser und geschweißter Stahlrohre zum Nachweis von Dopplungen
Dieser Teil der EN 10246 legt die Anforderungen an die Ultraschallprüfung der Rohrenden nahtloser und geschweißter Rohre über den gesamten Umfang zum Nachweis von Dopplungen fest. Die Norm enthält Festlegungen über Zulässigkeitsklassen und die Einstellung der Prüfanlagen. Dieser Teil der EN 10246 ist für die Prüfung von Rohren mit einem Außendurchmesser größer als 30 mm anwendbar. Für die Wanddicke ist keine untere Begrenzung festgelegt, es wird aber auf die Anmerkung in 3.1 verwiesen.
Essais non destructifs sur des tubes en acier - Partie 17: Contrôle par ultrasons des extrémités de tubes pour la détection de dédoublures des tubes en acier sans soudure et soudés
La présente partie de l'EN 10246 spécifie les prescriptions relatives au contrôle par ultrasons de toute la circonférence des extrémités de tubes sans soudure et soudés pour la détection des dédoublures. La norme spécifie des niveaux de sévérité et des procédures d'étalonnage. La présente norme européenne s'applique au contrôle de tubes soudés de diamètre extérieur supérieur à 30 mm. Aucune limite inférieure d'épaisseur n'est spécifiée mais voir note en 3.1. Les parties de la norme européenne EN 10246 "Essais non destructifs sur des tubes en acier" sont données en annexe A.
Neporušitveno preskušanje jeklenih cevi - 17. del: Ugotavljanje laminarnih napak koncev nevarjenih in varjenih jeklenih cevi z ultrazvočno preiskavo
General Information
- Status
- Withdrawn
- Publication Date
- 15-Feb-2000
- Withdrawal Date
- 31-Mar-2011
- Technical Committee
- ECISS/TC 110 - Steel tubes, and iron and steel fittings
- Drafting Committee
- ECISS/TC 29/SC 10 - Non-destructive testing
- Current Stage
- 9960 - Withdrawal effective - Withdrawal
- Start Date
- 01-Apr-2011
- Completion Date
- 01-Apr-2011
Relations
- Effective Date
- 22-Dec-2008
Frequently Asked Questions
EN 10246-17:2000 is a standard published by the European Committee for Standardization (CEN). Its full title is "Non-destructive testing of steel tubes - Part 17: Ultrasonic testing of tube ends of seamless and welded steel tubes for the detection of laminar imperfections". This standard covers: This Part of EN 10246 specifies requirements for the full peripheral ultrasonic testing of the ends of seamless and welded tubes for the detection of laminar imperfections. The standard specifies acceptance levels and calibration procedures. This Part of EN 10246 is applicable to the inspection of welded tubes with an outside diameter greater than 30 mm. No lower limit of wall thickness is specified but see note in 3.1. European Standard EN 10246 "Non destructive testing of steel tubes" comprises the parts shown in Annex A.
This Part of EN 10246 specifies requirements for the full peripheral ultrasonic testing of the ends of seamless and welded tubes for the detection of laminar imperfections. The standard specifies acceptance levels and calibration procedures. This Part of EN 10246 is applicable to the inspection of welded tubes with an outside diameter greater than 30 mm. No lower limit of wall thickness is specified but see note in 3.1. European Standard EN 10246 "Non destructive testing of steel tubes" comprises the parts shown in Annex A.
EN 10246-17:2000 is classified under the following ICS (International Classification for Standards) categories: 23.040.10 - Iron and steel pipes; 77.040.20 - Non-destructive testing of metals. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 10246-17:2000 has the following relationships with other standards: It is inter standard links to EN ISO 10893-8:2011. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 10246-17:2000 is associated with the following European legislation: EU Directives/Regulations: 97/23/EC; Standardization Mandates: M/005, M/071. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
EN 10246-17:2000 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.YRZerstörungsfreie Prüfung von Stahlrohren - Teil 17: Ultraschallprüfung der Rohrenden nahtloser und geschweißter Stahlrohre zum Nachweis von DopplungenEssais non destructifs sur des tubes en acier - Partie 17: Contrôle par ultrasons des extrémités de tubes pour la détection de dédoublures des tubes en acier sans soudure et soudésNon-destructive testing of steel tubes - Part 17: Ultrasonic testing of tube ends of seamless and weld
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...