EN 1440:2008/FprA1
(Amendment)LPG equipment and accessories - Periodic inspection of transportable refillable LPG cylinders
LPG equipment and accessories - Periodic inspection of transportable refillable LPG cylinders
This European Standard specifies inspection intervals, procedures for periodic inspection and testing, for transportable refillable welded and brazed steel LPG cylinders of water capacity from 0,5 l up to and including 150 l with a minimum wall thickness of 1,5 mm (see EN 1442 and EN 12807).
This standard does not apply to cylinders permanently installed in vehicles, or to plant and filling equipment.
Flüssiggas-Geräte und Ausrüstungsteile - Wiederkehrende Prüfung von ortsbeweglichen, wiederbefüllbaren Flaschen für Flüssiggas (LPG)
Equipement et accessoires GPL - Contrôle périodique des bouteilles de GPL transportables et réutilisables
Oprema in pribor za utekočinjeni naftni plin (UNP) - Periodični pregledi premičnih, ponovno polnljivih jeklenk za utekočinjeni naftni plin (UNP) - Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2011
2SUHPDLQSULERU]DXWHNRþLQMHQLQDIWQLSOLQ8133HULRGLþQLSUHJOHGLSUHPLþQLK
SRQRYQRSROQOMLYLKMHNOHQN]D813'RSROQLOR$
LPG equipment and accessories - Periodic inspection of transportable refillable LPG
cylinders
Flüssiggas-Geräte und Ausrüstungsteile - Wiederkehrende Prüfung von
ortsbeweglichen, wiederbefüllbaren Flaschen für Flüssiggas (LPG)
Equipement et accessoires GPL - Contrôle périodique des bouteilles de GPL
transportables et réutilisables
Ta slovenski standard je istoveten z: EN 1440:2008/FprA1
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
FINAL DRAFT
EN 1440:2008
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
September 2011
ICS 23.020.30
English Version
LPG equipment and accessories - Periodic inspection of
transportable refillable LPG cylinders
Equipement et accessoires GPL - Contrôle périodique des Flüssiggas-Geräte und Ausrüstungsteile - Wiederkehrende
bouteilles de GPL transportables et réutilisables Prüfung von ortsbeweglichen, wiederbefüllbaren Flaschen
für Flüssiggas (LPG)
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 286.
This draft amendment A1, if approved, will modify the European Standard EN 1440:2008. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1440:2008/FprA1:2011: E
worldwide for CEN national Members.
Contents Page
Foreword .3
1 Modifications to the Foreword .4
2 Modification to the Introduction .4
3 Modifications to Clause 2 .4
4 Modifications to Clause 3 .5
4.1 Modification to 3.1 .5
4.2 Modification to 3.2 .5
4.3 Modification to 3.3 .5
4.4 Modification to 3.5 .5
4.5 Modification to 3.7 .5
4.6 Modification to 3.8 .5
4.7 Addition of new term and definition 3.9 .5
5 Modification to Clause 4 .6
6 Modification to Clause 5 .6
6.1 Modification to 5.1 .6
6.2 Modification to 5.2 .8
6.3 Modification to 5.3 .9
7 Modification to Clause 6 .9
8 Modifications to Clause 7 . 14
9 Addition of Clause 8 . 14
10 Modification to Annex E . 15
11 Modification to Annex G . 15
12 Addition of new Annex H . 17
13 Addition of new Annex I . 18
14 Addition of new Annex J . 20
15 Modifications to the Bibliography . 21
Foreword
This document (EN 1440:2008/FprA1:2011) has been prepared by Technical Committee CEN/TC 286
“Liquefied Petroleum Gas equipement and accessories”, the secretariat of which is held by NSAI.
This document is currently submitted to the Unique Acceptance Procedure.
1 Modifications to the Foreword
th
1.1 Delete the last sentence from the 4 paragraph to read:
"This European Standard has been submitted for reference into the RID (Regulations concerning the
International Carriage of Dangerous Goods by Rail) and/or in the technical annexes of the ADR (European
Agreement concerning the international carriage of Dangerous goods by Road).".
th
1.2 Add new 7 paragraph summarising the scope of the changes in this amendment
"The changes in this amendment (EN 1440:2008/FprA1:2011) include:
inclusion of the new ADR requirement relative to the 15 year interval between periodic inspections
introduced in ADR 2011;
revision of procedures of periodic inspection in order to meet all ADR requirements;
introduction of a new annex dealing with the testing of cylinders with a water capacity less than
6,5 litres.".
2 Modification to the Introduction
rd
Delete the word "now" from the 3 paragraph to read:
"This European Standard has been prepared to reflect the current state of the art for period inspecting of LPG
cylinders, and is based on the operating experience of many hundreds of millions of cylinder years of service.".
3 Modifications to Clause 2
3.1 Delete the following references:
"EN 13152, Specification and testing of LPG cylinder valves – Self closing
EN 13153, Specification and testing of LPG cylinder valves – Manually operated".
3.2 Add the following new references:
"EN 13322-1, Transportable gas cylinders — Refillable welded steel gas cylinders — Design and
construction — Part 1: Carbon steel" and
"EN ISO 4628-3, Paints and varnishes — Evaluation of degradation of coatings — Designation of
quantity and size of defects, and of intensity of uniform changes in appearance — Part 3:
Assessment of degree of rusting (ISO 4628-3:2003)
EN ISO 14245, Gas cylinders — Specifications and testing of LPG cylinder valves — Self-closing
(ISO 14245:2006)
EN ISO 15995, Gas cylinders — Specifications and testing of LPG cylinder valves — Manually
operated (ISO 15995:2006)".
4 Modifications to Clause 3
4.1 Modification to 3.1
Replace term and definition 3.1 with new term and definition:
"inspection body
independent inspection and testing body approved by the competent authority".
4.2 Modification to 3.2
Replace definition 3.2 with new definition:
"person which by combination of appropriate qualification, training, experience, and resources, is able to make
objective judgments on the subject".
4.3 Modification to 3.3
Replace definition 3.3 with new definition:
"activities carried out at defined intervals, such as examining, measuring, testing or gauging the
characteristics of a pressure vessel and comparing these with specified requirements".
4.4 Modification to 3.5
Replace the definition and note in 3.5 with the following new definition:
"cylinder fully covered with a protection against impact and external corrosion so that the cylinder wall cannot
be seen".
4.5 Modification to 3.7
Replace term, definition and note 3.7 with new term and definition:
"liquefied petroleum gas
LPG
one or more light hydrocarbons which are assigned to UN 1011, UN 1075, UN 1965, UN 1969 or UN 1978
only and which consists mainly of propane, propene, butane, butane isomers, butene or traces of other
hydrocarbon gases".
4.6 Modification to 3.8
Replace term with "tare weight".
4.7 Addition of new term and definition 3.9
Insert new term and definition 3.9:
"3.9
competent authority
authority designated as such in each country in accordance with national regulation".
5 Modification to Clause 4
nd
5.1 In the 2 paragraph, after the NOTE, add “maximum” between “The” and “interval” to read as follows:
"The maximum interval between periodic inspections for welded steel, brazed steel and welded aluminium
LPG cylinders shall be 10 years.".
rd
5.2 Replace the 3 paragraph:
"However, for welded and brazed steel LPG cylinders, this period can be extended to 15 years, provided the
conditions of Annex E are fully met and approval from the relevant competent authority(ies) has been given.".
with the following paragraphs:
"However for welded and brazed steel LPG cylinders manufactured before the date 2015-01-01, this
maximum interval can be extended to 15 years, provided the conditions of Annex E are fully met and approval
from the relevant competent authority(ies) has been given.
The interval between periodic inspections of RID/ADR welded steel LPG cylinders can be extended to
15 years provided the requirements of Annex I are fulfilled and approval from the relevant competent authority
has been given.".
5.3 Delete the last sentence of the last paragraph:
“The inspection procedure to be applied shall be selected from the alternatives given in Clause 5.”.
6 Modification to Clause 5
6.1 Modification to 5.1
Replace the text and table in 5.1 and with the following:
"Periodic inspections/tests shall be carried out by a competent person under the control of an inspection
body based on a written scheme and in accordance with the procedures specified in Table 1.
For composite cylinders the written scheme shall be approved by the competent authority.
NOTE 1 A written scheme describes work procedures, criteria, responsibilities and other minimum requirements.
Cylinders rejected shall be segregated and be either reconditioned, re-tested or rendered unserviceable.
The decision to render a cylinder unserviceable can be taken at any stage during the periodic inspection
procedure. With agreement by the owner, a cylinder shall be rendered unserviceable in accordance with
EN 12816 so that it cannot be re-issued into service as a pressure vessel.
NOTE 2 In some countries, render unserviceable means scrapping.
Table 1 – Procedures for periodic inspection
Cylinder types Maximum periodic Procedures
inspection interval
Brazed steel cylinders 10 years External visual inspection as described in 6.1.2.1, 6.1.3
and Annex A
Welded steel cylinders in 15 years under the
Proof pressure test
conformity with EN 1442, conditions of Annex I
EN 13322-1 or Council
(hydraulic proof pressure test or pneumatic proof test and
Directive 84/527/EEC
leak test) as described in 5.2 and 6.2
Annex I parts 1 to 3
Internal condition check as described in 6.3.1 and Annex A
Welded and brazed steel 15 years under the Inspection of threads as described in 5.2 and 6.4
cylinders – manufactured conditions of Annex E
st
before 1 January 2015
Inspection of valves as described in 6.5
Welded steel cylinders in 10 years External visual inspection as described in 6.1.2.1, 6.1.3
conformity with EN 14140 and Annex B
or equivalent standard
Proo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.