EN 14025:2018/prA1
(Amendment)Tanks for the transport of dangerous goods - Metallic pressure tanks - Design and construction
Tanks for the transport of dangerous goods - Metallic pressure tanks - Design and construction
This document specifies the minimum requirements for the design and construction of metallic pressure tanks having a maximum working pressure exceeding 50 kPa (0,5 bar), for the transport of dangerous goods by road and rail and sea. This document includes requirements for openings, closures and structural equipment; it does not cover requirements of service equipment. For tanks for the transport of cryogenic liquids, EN 13530 1 and EN 13530 2 apply.
Design and construction of pressure tanks according to the Scope of this document are primarily subject to the requirements of RID/ADR, Subsections 6.8.2.1, 6.8.3.1 and 6.8.5, as relevant. In addition, the relevant requirements of RID/ADR, Table A, columns 12 and 13, to Chapters 3.2, 4.3 and Subsection 6.8.2.4 apply. For the structural equipment RID/ADR, Subsections 6.8.2.2 and 6.8.3.2 apply, as relevant. The definitions of RID/ADR, Subsection 1.2.1, are referred to. For portable tanks see also RID/ADR, Chapter 4.2 and Sections 6.7.2 and 6.7.2. In addition, the relevant requirements of RID/ADR, Table A, Columns 10 and 11 to Chapters 3.2, 4.2, and Sections 6.7.2 and 6.7.3 apply. The paragraph numbers above relate to the 2017 issue of RID/ADR which are subject to regular revisions. This can lead to temporary non-compliances with EN 14025.
This document is applicable to liquefied gases including LPG; however for a dedicated LPG standard see EN 12493.
If not otherwise specified, provisions which take up the whole width of the page apply to all kind of tanks. Provisions contained in a single column apply only to:
tanks according to RID/ADR Chapter 6.8 (left-hand column); portable tanks according to RID/ADR Chapter 6.7 (right-hand column).
Tanks für die Beförderung gefährlicher Güter - Metallische Drucktanks - Auslegung und Bau
Citernes pour le transport de matières dangereuses - Citernes métalliques sous pression - Conception et fabrication
Cisterne za prevoz nevarnega blaga - Kovinske tlačne posode - Konstruiranje in izdelava
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2020
Cisterne za prevoz nevarnega blaga - Kovinske tlačne posode - Konstruiranje in
izdelava
Tanks for the transport of dangerous goods - Metallic pressure tanks - Design and
construction
Tanks für die Beförderung gefährlicher Güter - Metallische Drucktanks - Auslegung und
Bau
Citernes pour le transport de matières dangereuses - Citernes métalliques sous pression
- Conception et fabrication
Ta slovenski standard je istoveten z: EN 14025:2018/prA1
ICS:
13.300 Varstvo pred nevarnimi Protection against dangerous
izdelki goods
23.020.20 Posode in vsebniki, montirani Vessels and containers
na vozila mounted on vehicles
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
EN 14025:2018
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
January 2020
ICS 13.300; 23.020.20
English Version
Tanks for the transport of dangerous goods - Metallic
pressure tanks - Design and construction
Citernes pour le transport de matières dangereuses - Tanks für die Beförderung gefährlicher Güter -
Citernes métalliques sous pression - Conception et Metallische Drucktanks - Auslegung und Bau
fabrication
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 296.
This draft amendment A1, if approved, will modify the European Standard EN 14025:2018. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a Eur
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.