Aerosol containers - Aerosol foam flammability test

This European Standard describes the method of determining the flammability of an aerosol product sprayed in the form of a foam, mousse, gel or paste.

Aerosolverpackungen - Prüfung der Brennbarkeit von Schaumprodukten

Diese Europäische Norm legt ein Verfahren zur Ermittlung der Brennbarkeit eines Aerosolproduktes, das in
Form von Schaum, Creme, Gel oder Paste ausgebracht wird fest.

Récipients pour aérosols - Essai d'inflammation des produits moussants en aérosols

La présente Norme européenne décrit une méthode permettant de déterminer l’inflammation d’un produit en générateur aérosol restitué sous la forme d’une mousse, d’un gel ou d’une pâte.

Embalaža za aerosole – Preskus vnetljivosti penastih aerosolov

If no  ignition of the sample is  apparent, reapply the ignition  source to the edge of the sample.  7.8 If ignition occurs, note the  following: maximum height of the  flame in centimetres above the  base of the watchglass; flame  duration in seconds. 7.9 Dry and  re-weigh the aerosol dispenser  and calculate the mass of the  released product. 7.10 Ventilate  the test area immediately after  each test. 7.11 If ignition does  not occur and the released  product remains in the form of a  foam, paste, mousse or gel  throughout the test, repeat steps  7.7 to 7.10. Allow the product to  stand for 30 s, 1 min, 2 min and  4 min before applying the ignition  source. 7.12 Repeat 7.5 to 7.11  twice more (a total of three) for  the same can. 7.13 Repeat 7.5 to  7.12 for another two aerosol cans  (three cans in total) of the same  product. 8 Test report The test  report shall include the following  information: a) whether the  product ignites; b) maximum  flame height in centimetres; c)  duration of flame in seconds; d)  mass of the product tested.

General Information

Status
Withdrawn
Publication Date
22-Nov-2005
Withdrawal Date
05-Aug-2009
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
06-Aug-2009
Completion Date
06-Aug-2009

Buy Standard

Standard
EN 14851:2006
English language
5 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-februar-2006
Embalaža za aerosole – Preskus vnetljivosti penastih aerosolov
Aerosol containers - Aerosol foam flammability test
Aerosolverpackungen - Prüfung der Brennbarkeit von Schaumprodukten
Récipients pour aérosols - Essai d'inflammation des produits moussants en aérosols
Ta slovenski standard je istoveten z: EN 14851:2005
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
55.130 3ORþHYLQNH]DDHURVROH Aerosol containers
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 14851
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2005
ICS 13.220.40; 55.130
English Version
Aerosol containers - Aerosol foam flammability test
Récipients pour aérosols - Essai d'infmammation des Aerosolpackungen - Prüfung der Brennbarkeit von
produits moussants en aérosols Schaumprodukten
This European Standard was approved by CEN on 14 October 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14851:2005: E
worldwide for CEN national Members.

Contents
1 Scope .4
2 Terms and definitions.4
3 Principle.4
4 Apparatus .4
5 Preparation of test apparatus .4
6 Test conditions .5
7 Test procedure .5
8 Test report .5

Foreword
This document (EN 14851:2005) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the
secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by May 2006, and conflicting national standards shall be withdrawn at the latest by
May 2006.
This draft European Standard is one of a series of thirteen related standards with the following titles:
EN 14847, Aerosol containers — Tinplate containers — Dimensions of the 25,4 mm aperture.
EN 14848, Aerosol containers — Metal containers with 25,4 mm aperture — Dimensions of valve cups.
EN 14849, Aerosol containers — Glass containers — Dimensions of aerosol valve ferrules.
EN 14850, Aerosol containers — Metal containers with 25,4 mm aperture — Measurement of contact height.
EN 14851, Aerosol containers — Aerosol foam flammability test.
EN 14852, Aerosol containers — Determination of the ignition distance of the spray jet.
EN 14853, Aerosol containers — Enclosed space ignition test.
EN 14854, Aerosol containers — Glass containers — Dimensions of the neck finish.
prEN 15006, Metal aerosol containers — Aluminium containers — Dimensions of the 25,4 mm (one inch) aperture.
prEN 15007, Metal aerosol containers — Tinplate containers — Dimensions of three-piece cans.
prEN 15008, Metal aerosol containers —Dimensions of 1-piece aluminium can with
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.