EN ISO 13085:2014

SLOVENSKI STANDARD
01-julij-2014
Industrija za predelavo nafte in zemeljskega plina - Cevi iz aluminijevih zlitin, ki se
uporabljajo kot cevovodi za vrtine (ISO 13085:2014)
Petroleum and natural gas industries - Aluminium alloy pipe for use as tubing for wells
(ISO 13085:2014)
Erdöl- und Erdgasindustrie - Rohre aus Aluminiumlegierungen zur Verwendung als
Steigrohre für Bohrungen (ISO 13085:2014)
Industries du pétrole et du gaz naturel - Tubes en alliage d'aluminium utilisés comme
tubes de production dans les puits (ISO 13085:2014)
Ta slovenski standard je istoveten z: EN ISO 13085:2014
ICS:
75.180.10 Oprema za raziskovanje in Exploratory and extraction
odkopavanje equipment
77.150.10 Aluminijski izdelki Aluminium products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 13085
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2014
ICS 77.150.10; 75.180.10
English Version
Petroleum and natural gas industries - Aluminium alloy pipe for
use as tubing for wells (ISO 13085:2014)
Industries du pétrole et du gaz naturel - Tubes en alliage Erdöl- und Erdgasindustrie - Rohre aus
d'aluminium utilisés comme tubes de production dans les Aluminiumlegierungen zur Verwendung als Steigrohre für
puits (ISO 13085:2014) Bohrungen (ISO 13085:2014)
This European Standard was approved by CEN on 4 January 2014.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13085:2014 E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
This document (EN ISO 13085:2014) has been prepared by Technical Committee ISO/TC 67 “Materials,
equipment and offshore structures for petroleum, petrochemical and natural gas industries” in collaboration
with Technical Committee CEN/TC 12 “Materials, equipment and offshore structures for petroleum,
petrochemical and natural gas industries” the secretariat of which is held by AFNOR.
Endorsement notice
The text of ISO 13085:2014 has been approved by CEN as EN ISO 13085:2014 without any modification.

INTERNATIONAL ISO
STANDARD 13085
First edition
2014-03-15
Petroleum and natural gas
industries — Aluminium alloy pipe for
use as tubing for wells
Industries du pétrole et du gaz naturel — Tubes en alliage
d’aluminium utilisés comme tubes de production dans les puits
Reference number
ISO 13085:2014(E)
©
ISO 2014
ISO 13085:2014(E)
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

ISO 13085:2014(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and symbols . 1
3.1 Terms and definitions . 1
3.2 Symbols . 2
4 Information to be supplied by purchaser . 3
5 Process of manufacture and delivery condition . 3
5.1 General . 3
5.2 Heat treatment . 3
5.3 Traceability . 3
5.4 Delivery condition . 4
6 Material requirements . 4
6.1 Material groups . 4
6.2 Metallographic examination . 4
6.3 Chemical composition . 5
6.4 Tensile properties . 5
7 Configuration and dimensions of pipes . 5
7.1 Configuration . 5
7.2 Length . 5
7.3 Dimensions of pipes . 5
7.4 Design mass . 6
7.5 Upset run-out . 6
7.6 Straightness . 6
7.7 Ovality and eccentricity of pipes . 6
7.8 Drift requirements . 6
7.9 Internal coating . 6
8 Test methods . 6
9 Measuring methods . 8
10 Inspection . 9
11 Marking . 9
12 Packaging, transport and storage . 9
13 Documents . 9
13.1 Certification . 9
13.2 Retention of records .10
14 Delivery conditions .10
15 Minimum facility requirements for pipe mill .10
Annex A (normative) Purchaser inspection .11
Annex B (normative) Corrosion test .12
Bibliography .13
ISO 13085:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of t
...