Rubber or plastics hoses and hose assemblies - Hydraulic-pressure impulse test without flexing (ISO 6803:2017)

ISO 6803:2017 describes hose impulse testing, without flexing, of rubber or plastics hydraulic hose assemblies at both high and low impulse pressures. The high-pressure testing is carried out at pressures greater than 3 MPa and the low-pressure testing at pressures from 1,5 MPa to 3 MPa. The test procedure is applicable to hydraulic hose assemblies that are subject to pulsating pressures in service which are included in the product requirements.
NOTE          Impulse test procedures with flexing can be found in ISO 6802.

Gummi- oder Kunststoffschläuche und -schlauchleitungen - Hydraulik-Druck-Impulsprüfung ohne Biegung (ISO 6803:2017)

Tuyaux et flexibles en caoutchouc ou en plastique - Essai d'impulsions de pression hydraulique sans flexion (ISO 6803:2017)

ISO 6803:2017 décrit un essai d'impulsions de pression hydraulique, sans flexion, des tuyaux et flexibles en caoutchouc ou en plastique à haute pression et à basse pression. L'essai à haute pression est réalisé à des pressions d'essai supérieures à 3 Mpa et l'essai à basse pression est réalisé à des pressions d'essai de 1,5 MPa à 3 Mpa inclus. La méthode d'essai est applicable aux flexibles hydrauliques qui sont sujets à des pressions pulsatoires en service, lesquelles sont incluses dans les exigences de produit.
NOTE          Les méthodes d'essai d'impulsions avec flexion peuvent être trouvées dans l'ISO 6802.

Gumene ali polimerne cevi ter cevni priključki - Hidravlično tlačno sunkovno preskušanje brez upogibanja (ISO 6803:2017)

Ta dokument opisuje sunkovno preskušanje gumenih ali polimernih hidravličnih cevnih priključkov brez upogibanja
tako pri visokih kot pri nizkih vrednostih sunkov tlaka. Visokotlačno preskušanje se izvaja pri vrednostih tlaka nad 3 MPa, nizkotlačno preskušanje pa pri vrednostih tlaka od 1,5 MPa do 3 MPa. Preskusni postopek se uporablja za hidravlične cevne priključke, ki so pri uporabi izpostavljeni tlačnim sunkom, vključenim v zahtevah za proizvod.
OPOMBA: Postopki sunkovitega preskušanja z upogibanjem so navedeni v standardu ISO 6802.

General Information

Status
Published
Publication Date
14-Mar-2017
Withdrawal Date
29-Sep-2017
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
15-Mar-2017
Completion Date
15-Mar-2017

Relations

Buy Standard

Standard
EN ISO 6803:2017
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 6803:2017
01-maj-2017
1DGRPHãþD
SIST EN ISO 6803:2009
*XPHQHDOLSROLPHUQHFHYLWHUFHYQLSULNOMXþNL+LGUDYOLþQRWODþQRVXQNRYQR
SUHVNXãDQMHEUH]XSRJLEDQMD ,62
Rubber or plastics hoses and hose assemblies - Hydraulic-pressure impulse test without
flexing (ISO 6803:2017)
Tuyaux et flexibles en caoutchouc ou en plastique - Essai d'impulsions de pression
hydraulique sans flexion (ISO 6803:2017)
Ta slovenski standard je istoveten z: EN ISO 6803:2017
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
SIST EN ISO 6803:2017 de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 6803:2017

---------------------- Page: 2 ----------------------

SIST EN ISO 6803:2017


EN ISO 6803
EUROPEAN STANDARD

NORME EUROPÉENNE

March 2017
EUROPÄISCHE NORM
ICS 23.040.70; 23.100.40 Supersedes EN ISO 6803:2008
English Version

Rubber or plastics hoses and hose assemblies - Hydraulic-
pressure impulse test without flexing (ISO 6803:2017)
Tuyaux et flexibles en caoutchouc ou en plastique - Gummi- oder Kunststoffschläuche und -
Essai d'impulsions de pression hydraulique sans schlauchleitungen - Hydraulik-Druck-Impulsprüfung
flexion (ISO 6803:2017) ohne Biegung (ISO 6803:2017)
This European Standard was approved by CEN on 10 September 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6803:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 6803:2017
EN ISO 6803:2017 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 6803:2017
EN ISO 6803:2017 (E)
European foreword
This document (EN ISO 6803:2017) has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products" in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses
and hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2017 and conflicting national standards
shall be withdrawn at the latest by September 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 6803:2008.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 6803:2017 has been approved by CEN as EN ISO 6803:2017 without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 6803:2017

---------------------- Page: 6 ----------------------

SIST EN ISO 6803:2017
INTERNATIONAL ISO
STANDARD 6803
Fourth edition
2017-03
Rubber or plastics hoses and hose
assemblies — Hydraulic-pressure
im
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.