EN ISO 3691-6:2021

SLOVENSKI STANDARD
01-februar-2022
Nadomešča:
SIST EN ISO 3691-6:2016
SIST EN ISO 3691-6:2016/AC:2016
Vozila za talni transport - Varnostne zahteve in preverjanje - 6. del: Tovorni in
osebni vozički (ISO 3691-6:2021)
Industrial trucks - Safety requirements and verification - Part 6: Burden and personnel
carriers (ISO 3691-6:2021)
Flurförderzeuge - Sicherheitstechnische Anforderungen und Verifizierung - Teil 6:
Lasten- und Personentransportfahrzeuge (ISO 3691-6:2021)
Chariots de manutention - Exigences de sécurité et vérification - Partie 6: Transporteurs
de charges et de personnel (ISO 3691-6:2021)
Ta slovenski standard je istoveten z: EN ISO 3691-6:2021
ICS:
53.060 Industrijski tovornjaki Industrial trucks
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 3691-6
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2021
EUROPÄISCHE NORM
ICS 53.060; C Supersedes EN ISO 3691-6:2015, EN ISO 3691-
6:2015/AC:2016
English Version
Industrial trucks - Safety requirements and verification -
Part 6: Burden and personnel carriers (ISO 3691-6:2021)
Chariots de manutention - Exigences de sécurité et Flurförderzeuge - Sicherheitstechnische
vérification - Partie 6: Transporteurs de charges et de Anforderungen und Verifizierung - Teil 6: Lasten- und
personnel (ISO 3691-6:2021) Personentransportfahrzeuge (ISO 3691-6:2021)
This European Standard was approved by CEN on 11 August 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3691-6:2021 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered . 4

European foreword
This document (EN ISO 3691-6:2021) has been prepared by Technical Committee ISO/TC 110
"Industrial trucks" in collaboration with Technical Committee CEN/TC 150 “Industrial Trucks - Safety”
the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2022, and conflicting national standards shall be
withdrawn at the latest by April 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3691-6:2015 and EN ISO 3691-6:2015/AC:2016.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s) / Regulation(s).
For the relationship with EU Directive(s) / Regulation(s), see informative Annex ZA, which is an integral
part of this document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 3691-6:2021 has been approved by CEN as EN ISO 3691-6:2021 without any
modification.
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered
This European Standard has been prepared under a Commission’s standardization request “M/396
Mandate to CEN and CENELEC for Standardisation in the field of machinery" to provide one voluntary
means of conforming to essential requirements of Directive 2006/42/EC of the European Parliament
and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast).
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of Directive
2006/42/EC
The relevant Essential Clause(s)/sub-clause(s) of Remarks/Notes
Requirements of Directive this EN
2006/42/EC
To cover all the relevant safety
requirements for the products(s) in
its scope, this standard (providing
global requirements and references
to regional requirements for a
machine) has to be applied together
with one of those standards as
specified in the scope (providing
European regional requirements for
a machine).
1.1.2. Principles of safety 4, 5, 6
integration
1.1.3. Materials and products 4.1, 4.5
1.1.4. Lighting 4.9.2
1.1.5. Design of machinery to 4.11, 6.2, 6.3
facilitate its handling
1.1.6 Ergonomics 4.6
1.1.7. Operating positions 4.5.1, 4.10, 6.2, 6.3
1.1.8. Seating 4.6.3
1.2.1. Safety and reliability of  not covered
The relevant Essential Clause(s)/sub-clause(s) of Remarks/Notes
Requirements of Directive this EN
2006/42/EC
control systems
1.2.2 Control devices 4.2.2.3, 4.2.2.5, 4.4
1.2.3. Starting  not covered
1.2.4.1. Normal stop  not covered
1.2.4.2. Operational stop  not covered
1.2.4.3. Emergency stop , not covered
1.2.5. Selection of control or 4.4.2.6,
operating modes
1.2.6. Failure of the power supply 4.3.3, 4.4.3.2
1.3.1. Risk of loss of stability 4.7
1.3.2. Risk of break-up during not covered
operation
1.3.3. Risks due to falling or ejected 4.6.3.4, 4.8.4, 4.11.1,
objects
1.3.4. Risks due to surfaces, edges 4.1.4, 4.4.2.6.5, 4.5.3.1
or angles
1.3.7. Risks related to moving parts 4.5.3, 4.6.3.4, 4.8.2
1.3.8.1. Moving transmission parts 4.5.3.1
1.3.9. Risks of uncontrolled  not covered
movements
1.4.1. General requirements  not covered
1.4.2.1. Fixed guards  not covered
1.4.2.2. Interlocking movable  not covered
guards
1.4.3. Special requirements for  not covered
protective devices
1.5.1. Electricity supply  not covered
1.5.2. Static electricity  not covered
The relevant Essential Clause(s)/sub-clause(s) of Remarks/Notes
Requirements of Directive this EN
2006/42/EC
1.5.3. Energy supply other than 4.5, 4.8.3
electricity
1.5.4. Errors of fitting  not covered
1.5.5. Extreme temperatures  not covered
1.5.6. Fire 4.5.2, 4.5.4, 4.5.1.1, 4.10.1.1
1.5.7. Explosion 4.5.2. 4.5.4
1.5.8. Noise  not covered
1.5.9. Vibrations  not covered
1.5.10. Radiation  not covered
1.5.11. External radiation  not covered
1.5.13. Emissions of hazardous 4.5.1.1
materials and substances
1.5.14. Risk of being trapped in a 4.10.1.5
machine
1.5.15. Risk of slipping, tripping or 4.6.2, 4.6.3.3
falling
1.5.16. Lightning  not covered
1.6.1. Machinery maintenance  not covered
1.6.2. Access to operating positions 4.5.3.1
and servicing points
1.6.3. Isolation of energy sources  not covered
1.6.4. Operator intervention 4.4.2.6.5
1.7.1. Information and warnings on 6.3
the machinery
1.7.1.1. Information and 4.4.4, 6.3.2
information devices
1.7.1.2. Warning devices 4.8.1
1.7.2. Warning of residual risks 6.3.3.4
The relevant Essential Clause(s)/sub-clause(s) of Remarks/Notes
Requirements of Directive this EN
2006/42/EC
1.7.3. Marking of machinery 6.3
1.7.4. Instructions 6.1, 6.2
1.7.4.1. General principles for the 6.1
drafting of instructions
1.7.4.2. Contents of the instructions 6.2
1.7.4.3. Sales literature  not covered
3.2.1. Driving position  not covered
3.2.2. Seating 4.6.3.3
3.2.3. Positions for other persons 4.6.3.2
3.3.1. Control devices 4.4
3.3.2. Starting/moving 4.2.2.2, 4.2.2.4
3.3. Control systems 4.2.1
3.3.3. Travelling function 4.2, 4.3
3.3.4. Movement of pedestrian- not covered
controlled machinery
3.3.5. Control circuit failure 4.4.3.2
3.4.1. Uncontrolled movements 4.7, 4.8.4
3.4.2. Moving transmission parts 4.5.3
3.4.3. Roll-over and tip-over  not covered
3.4.4. Falling objects  not covered
3.4.5. Means of access  not covered
3.4.6. Towing devices 4.4.2.6.5
3.5.1. Batteries 4.8.4, 4.8.5
The relevant Essential Clause(s)/sub-clause(s) of Remarks/Notes
Requirements of Directive this EN
2006/42/EC
3.5.2. Fire not covered
3.6.1. Signs, signals and warnings 4.8.1, 4.9.2
3.6.2. Marking 6.3.1
3.6.3. Instructions 6
3.6.3.1. Vibrations  not covered
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 3691-6
Second edition
2021-07
Industrial trucks — Safety
requirements and verification —
Part 6:
Burden and personnel carriers
Chariots de manutention — Exigences de sécurité et vérification —
Partie 6: Transporteurs de charges et de personnel
Reference number
ISO 3691-6:2021(E)
©
ISO 2021
ISO 3691-6:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved

ISO 3691-6:2021(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Safety requirements and/or protective measures . 3
4.1 General . 3
4.1.1 Overall requirements . 3
4.1.2 Normal climatic conditions.
...