iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1015-21:2002

(Main)

Methods of test for mortar for masonry - Part 21: Determination of the compatibility of one-coat rendering mortars with substrates

Methods of test for mortar for masonry - Part 21: Determination of the compatibility of one-coat rendering mortars with substrates

This European Standard specifies a test method for the evaluation of the compatibility with given backgrounds of One-Coat (OC) rendering mortars. The evaluation is based on the determination of the adhesion strength and water permeability of the hardened render applied on tested substrates, after exposure to weathering cycles.

Prüfverfahren für Mörtel für Mauerwerk - Teil 21: Bestimmung der Verträglichkeit von Einlagenputzmörteln mit Untergründen

Diese Europäische Norm legt die Verfahren zur Bewertung der Verträglichkeit von Einlagenputzmörteln (OC) mit den in Frage kommenden Untergründen fest. Die Bewertung basiert auf der Bestimmung der Haftfestigkeit und der Wasserdurchlässigkeit des erhärteten Putzes, der auf geprüften Untergründen aufgetragen und bewittert wurde.

Méthodes d'essai des mortiers pour maçonnerie - Partie 21: Détermination de la compatibilité des mortiers d'enduit extérieur mono-couche avec les supports

La présente Norme européenne décrit une méthode de détermination de la compatibilité des mortiers d'enduit mono-couche (MC) avec les supports sur lesquels ils doivent être appliqués.
Cette détermination est basée sur la mesure de l'adhérence et de la perméabilité à l'eau de l'enduit durci appliqué sur des supports définis, après cycles de conditionnement.

Metode preskušanja zidarske malte – 21. del: Določevanje združljivosti enoslojnih ometov s podlagami

General Information

Status
Published
Publication Date
03-Dec-2002
ICS
91.100.10 - Cement. Gypsum. Lime. Mortar
Technical Committee
CEN/TC 125 - Masonry
Drafting Committee
CEN/TC 125/WG 4 - Test methods
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
23-Jan-2024
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Ref Project
SIST EN 1015-21:2004 - Methods of test for mortar for masonry - Part 21: Determination of the compatibility of one-coat rendering mortars with substrates

Buy Standard

EN 1015-21:2004EN 1015-21:2004
PreviousNext
Standard
EN 1015-21:2004
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Prüfverfahren für Mörtel für Mauerwerk - Teil 21: Bestimmung der Verträglichkeit von Einlagenputzmörteln mit UntergründenMéthodes d'essai des mortiers pour maçonnerie - Partie 21: Détermination de la compatibilité des mortiers d'enduit extérieur mono-couche avec les supportsMethods of test for mortar for masonry - Part 21: Determination of the compatibility of one-coat rendering mortars with substrates91.100.10Cement. Mavec. Apno. MaltaCement. Gypsum. Lime. MortarICS:Ta slovenski standard je istoveten z:EN 1015-21:2002SIST EN 1015-21:2004en01-januar-2004SIST EN 1015-21:2004SLOVENSKI
STANDARD



SIST EN 1015-21:2004



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1015-21December 2002ICS 91.100.10English versionMethods of test for mortar for masonry - Part 21: Determinationof the compatibility of one-coat rendering mortars withsubstratesMéthodes d'essai des mortiers pour maçonneries - Partie21: Détermination de la compatibilité des mortiers d'enduitextérieur mono-couches avec leur armaturePrüfverfahren für Mörtel für Mauerwerk - Teil 21:Bestimmung der Verträglichkeit von Einlagenputzmörtelnmit UntergründenThis European Standard was approved by CEN on 6 July 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1015-21:2002 ESIST EN 1015-21:2004



EN 1015-21:2002 (E)2ContentspageForeword.31Scope.42Normative references.43Principle.44Apparatus.45Sampling and sample preparation.66Preparation and storage of test specimens.77Procedure.88Expression of the results.89Test report.9SIST EN 1015-21:2004



EN 1015-21:2002 (E)3ForewordThis document (EN 1015-21:2002) has been prepared by Technical Committee CEN/TC 125"Masonry", the secretariat of which is held by BSI.This European Standard shall be given the status of a national standard, either by publication of anidentical text or by endorsement, at the latest by June 2003, and conflicting national standards shallbe withdrawn at the latest by September 2004.According to the CEN/CENELEC Internal Regulations, the national standards organizations of thefollowing countries are bound to implement this European Standard: Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta,Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.SIST EN 1015-21:2004



EN 1015-21:2002 (E)41 ScopeThis European Standard specifies a test method for determining the compatibility of One-Coat (OC)rendering mortars with given substrates.The ev
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 15824:2017(Main)
Specifications for external renders and internal plasters based on organic binders
SIST EN 15824:2017

This European Standard is applicable to factory-made renders and plasters based on organic binders used for external or internal covering on walls, columns, partitions and ceilings. The products are manufactured in paste form, ready to use, or in powder form. This European Standard is also applicable to renders and plasters with inorganic binders such as silicates, silanes, siloxanes and silicones.
Renders and plasters can form the final surface of the structure, textured or not, or they can provide a levelling of the substrate, adequately smooth for subsequent decorative treatments.
This European Standard contains definitions and final performance requirements. It includes relevant characteristic categories to designate renders and plasters.
This European Standard provides for the assessment and verification of constancy of performance (AVCP) of the product to this European Standard. The marking requirement for products covered by this European Standard is included.
This European Standard is not applicable to coating materials and coating systems according to EN 1062-1 and EN 13300.
This European Standard does not contain recommendations for the design and application of renders and plasters. However, this European Standard may be used for definition of renders and plasters in conjunction with codes of application and national specifications for execution of works.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 998-2:2016(Main)
Specification for mortar for masonry - Part 2: Masonry mortar
SIST EN 998-2:2017

This European Standard specifies requirements for factory-made masonry mortars (bedding, jointing and pointing) for use in masonry walls, columns and partitions (e.g. facing and rendered masonry, load bearing or non-load bearing masonry structures for buildings and civil engineering works).
This European Standard defines for fresh mortar the performance related to workable life, chloride content, air content, density and correction time (for thin-layer mortar only). For hardened mortar it defines, e.g. performances related to compressive strength, bond strength, density measured according to the corresponding test methods contained in separate European Standards.
This European Standard provides for the assessment and verification of constancy of performance (AVCP) of the product to this European Standard. The marking requirement for products covered by this European Standard is included.
This European Standard covers masonry mortars defined in Clause 3 with the exception of site made mortar. However, this European Standard or part of this European Standard may be used in conjunction with codes of application and national specifications covering site made mortar.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 998-1:2016(Main)
Specification for mortar for masonry - Part 1: Rendering and plastering mortar
SIST EN 998-1:2017

This European Standard is applicable to factory-made rendering/plastering mortars based on inorganic binders for external (rendering) and internal (plastering) use on walls, ceilings, columns and partitions. It contains definitions and final performance requirements.
This European Standard provides for the assessment and verification of constancy of performance (AVCP) of the product to this European Standard. The marking requirement for products covered by this European Standard is included.
It does not cover mortars where calcium sulphate binder is the principal active binding agent.
Calcium sulphate binder can be used as an additional binder together with air lime. If air lime is the principal active binding component, the rendering/plastering mortar is covered by this European Standard. If the calcium sulphate binder is the principal active binding component, the mortar is covered by EN 13279.
Special fire resistant- and acoustical mortars, mortars for structural repair and surface treatments of building elements such as materials for smoothing or trueing, paints, coatings, thin-layer organic renders/plasters and prefabricated units (e.g. plasterboards) are not dealt with in this European Standard.
This European Standard covers rendering/plastering mortars defined in Clause 3 with the exception of site-made rendering/plastering mortars. However, this European Standard or part of this European Standard may be used in conjunction with codes of application and national specifications covering site-made mortar.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1015-12:2016(Main)
Methods of test for mortar for masonry - Part 12: Determination of adhesive strength of hardened rendering and plastering mortars on substrates
SIST EN 1015-12:2016

This European Standard specifies a method for the determination of the adhesive strength between rendering and plastering mortars and a substrate.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13914-1:2016(Main)
Design, preparation and application of external rendering and internal plastering - Part 1: External rendering
SIST EN 13914-1:2016

This European Standard specifies requirements and recommendations for the design, preparation and application of
-   renders based on cement, lime or other mineral binders, and/or combinations thereof, masonry cement and polymer modified binder based external renderings, in accordance with FprEN 998-1 or site made renders;
-   renders based on organic binders in accordance with FprEN 15824
on all common types of backgrounds. It includes rendering on both new and old backgrounds and the maintenance and repair of existing work. This document gives guidance on the use of established site, factory and semi-finished factory made renders.
This document does not cover the following:
a)   the use and application of special renders for liquid retaining structures, e.g. coatings, and for backgrounds to cladding systems;
b)   the structural repair of concrete;
c)   the installation of external thermal insulation composite systems (ETICS);
d)   the specification and use of sealants used to seal joints for use with rendering;
e)   the use of gypsum based renders used externally, but their use may be permitted in some countries;
Gypsum based products soften when subject to prolonged moist conditions. The use of such products externally will depend upon the climatic conditions where the render will be used and on the local building traditions. With the exception of some drier countries in southern Europe gypsum based renders are generally not recommended for external use and are therefore not included within the scope of this document. However, their use may be permitted and controlled locally. )
f)   renders on historical monuments or buildings in protected areas which may be regulated by national codes;
g)   the design and installation of flashings at windowsills and elsewhere.
Because of the many and varied materials and practices and different climatic conditions in Europe it is not possible for certain aspects of the standard to enter into sufficient detail to be fully usable to practitioners in each country. Appropriate guidance to complement, but not alter any basic European recommendations is given in documentation prepared by each country. Aspects of this European Standard whose basic recommendations may need to be complemented are indicated where they occur by a footnote referencing this clause.

  • Standard
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13914-2:2016(Main)
Design, preparation and application of external rendering and internal plastering - Part 2: Internal plastering
SIST EN 13914-2:2016

This European Standard deals with the design considerations and essential principles for internal plastering systems and application of plastering systems.
The different parts of the EN 13914 series of standards specify requirements and recommendations for detailing, design and material considerations, the selection of mixes and the application of gypsum plasters, gypsum/lime plasters, lightweight plasters, lime/gypsum-, cement- and cement/lime-based plasters, lime-based plasters, clay plasters, silicate plasters, organic plasters, polymer-modified plasters, etc.
This standard does not deal with the following:
-   external finishes;
-   painting and/or preparation;
-   impregnations;
-   structural repair of concrete;
-   prefabricated fibre-reinforced plaster elements.
Owing to the many and varied materials and practices and different climatic conditions in Europe it is not possible for certain aspects of the standard to enter into sufficient detail to be fully usable to practitioners in each country. Such guidance to complement, but not alter, any basic European recommendations is given in documentation prepared by each country. Aspects of this European Standard, the basic recommendations of which may need to be complemented, are indicated where they occur by a footnote referencing this clause.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1015-2:1998/A1:2006(Amendment)
Methods of test for mortar for masonry - Part 2: Bulk sampling of mortars and preparation of test mortars
SIST EN 1015-2:1999/A1:2007

Modification to Foreword, Clause 2, 3.3, 5.3 and 6.2.2.

  • Amendment
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1015-1:1998/A1:2006(Amendment)
Methods of test for mortar for masonry - Part 1: Determination of particle size distribution (by sieve analysis)
SIST EN 1015-1:1999/A1:2007

Modifications to Foreword, Clause 2 and 7.1

  • Amendment
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1015-3:1999/A2:2006(Amendment)
Methods of test for mortar for masonry - Part 3: Determination of consistence of fresh mortar (by flow table)
SIST EN 1015-3:2001/A2:2007

Modification to Clause 2 and Clause 6.

  • Amendment
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1015-9:1999/A1:2006(Amendment)
Methods of test for mortar for masonry - Part 9: Determination of workable life and correction time of fresh mortar
SIST EN 1015-9:2001/A1:2007

Modification do Clause 2 and 8.2.

  • Amendment
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day