EN 22858:1993
(Main)End-suction centrifugal pumps (rating 16 bar) - Designation, nominal duty point and dimensions (ISO 2858:1975)
End-suction centrifugal pumps (rating 16 bar) - Designation, nominal duty point and dimensions (ISO 2858:1975)
Specifies the main parameters and describes the pump designation which consits of three numbers. The table covers flange sizes from 50 mm up to and including 200 mm. A figure shows the side view and the front view of the pump.
Kreiselpumpen mit axialem Eintritt PN 16 - Bezeichnung, Nennleistung und Abmessungen (ISO 2858:1975)
Pompes centrifuges à aspiration en bout (pression nominale 16 bar) - Désignation, point de fonctionnement nominal et dimensions (ISO 2858:1975)
La présente Norme Internationale spécifie les dimensions principales et le point de fonctionnement nominal des pompes centrifuges à aspiration en bout ayant une pression nominale de 16 bar.2) 1) Le constructeur doit être consulté au sujet de la limitation de température. 2) 1 bar = 0,1 MPa.
End-suction centrifugal pumps (rating 16 bar) - Designation, nominal duty point and dimensions (ISO 2858:1975)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.End-suction centrifugal pumps (rating 16 bar) - Designation, nominal duty point and dimensions (ISO 2858:1975)Kreiselpumpen mit axialem Eintritt PN 16 - Bezeichnung, Nennleistung und Abmessungen (ISO 2858:1975)Pompes centrifuges a aspiration en bout (pression nominale 16 bar) - Désignation, point de fonctionnement nominal et dimensions (ISO 2858:1975)End-suction centrifugal pumps (rating 16 bar) - Designation, nominal duty point and dimensions (ISO 2858:1975)23.080ýUSDONHPumpsICS:Ta slovenski standard je istoveten z:EN 22858:1993SIST EN 22858:2000en01-december-2000SIST EN 22858:2000SLOVENSKI
STANDARD
INTERNATIONAL STANDARD. INTERNATIONAL ORGANIZATION FOR STANDARDIZATION .MEXAYHAPOAHAII OPFAHM3AUMfl l-IO CTAHAAPTC13AWWi *ORGANISATION INTERNATIONALE DE NORMALISATION End-suction centrifugal Pumps (rating 16 bar) - Designath, nominal duty Point and dimensions Pompes ten trifuges 6 aspira tion en bout (Pression nominale 16 bar) - Dksigna tion, poin t de fonctionnemen t nominal et dimensions Second edition - 1975-02-15 UDC 621.671 Descriptors : Pumps, centrifugal Pumps, dimensions, specifications, designation. Ref. No. ISO 2858-1975 (E) Price based on 2 pages SIST EN 22858:2000
FQREWQRD ISO (the International Organization for Standardization) is a worldwide federation of national standards institutes (ISO Member Bodies). The work of developing International Standards is carried out through ISO Technical Committees. Every Member Body interested in a subject for which a Technical Committee has been set up has the right to be represented on that Committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. Draft International Standards adopted by the Technical Committees are circulated to the Member Bodies for approval before their acceptance as International Standards by the ISO Council. International Standard ISO 2858 (2nd Edition) was drawn up by Technical Committee lSO/TC 115, Pumps. lt was submitted directly to the ISO Council, in accordance with clause 6.12.1 sf the Directives for the technical work of ISO. This International Standard cancels and replaces International Standard ISO 2858-1973, which had been approved by the Member Bedies of the following countries : Austria Israel Belgium Italy Egypt, Arab Rep. of Netherlands France New Zealand Germany Norway Hungary Portugal I ndia Roma nia Ireland South Africa
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.