EN ISO 2286-3:1998

SLOVENSKI STANDARD
01-marec-1999
Gumirane ali plastificirane tekstilije - Ugotavljanje lastnosti zvitka - 3. del: Metoda
za ugotavljanje debeline (ISO 2286-3:1998)
Rubber- or plastics-coated fabrics - Determination of roll characteristics - Part 3: Method
for determination of thickness (ISO 2286-3:1998)
Mit Kautschuk oder Kunststoff beschichtete Textilien - Bestimmung der
Rollencharakteristik - Teil 3: Bestimmung der Dicke (ISO 2286-3:1998)
Supports textiles revetus de caoutchouc ou de plastique - Détermination des
caractéristiques des rouleaux - Partie 3: Méthode de détermination de l'épaisseur (ISO
2286-3:1998)
Ta slovenski standard je istoveten z: EN ISO 2286-3:1998
ICS:
59.080.40 3RYUãLQVNRSUHYOHþHQH Coated fabrics
WHNVWLOLMH
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERNATIONAL ISO
STANDARD 2286-3
First edition
1998-06-01
Rubber- or plastics-coated fabrics —
Determination of roll characteristics —
Part 3:
Method for determination of thickness
Supports textiles revêtus de caoutchouc ou de plastique — Détermination
des caractéristiques des rouleaux —
Partie 3: Méthode de détermination de l'épaisseur
A
Reference number
ISO 2286-3:1998(E)
ISO 2286-3:1998(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 2286-3 was prepared by Technical Committee
ISO/TC 45, Rubber and rubber products.
Together with the other parts (see below), it cancels and replaces
ISO 2286:1986, which has been technically revised.
ISO 2286 consists of the following parts, under the general title Rubber-
and plastics-coated fabrics — Determination of roll characteristics:
— Part 1: Methods for determination of length, width and net mass
— Part 2: Methods for determination of total mass per unit area, mass per
unit area of coating and mass per unit area of substrate
— Part 3: Method for determination of thickness
©  ISO 1998
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet iso@iso.ch
Printed in Switzerland
ii
©
ISO ISO 2286-3:1998(E)
Introduction
Compared with metals, coated fabrics are easily compressed, and the
measured thickness will depend considerably upon the method and
pressure employed. This is perhaps the single most important reason for
having a standard method for measuring the thickness of coated fabrics.
An effort has been made to enable the results to be comparable with
measurements of the thickness of textile substrates.
iii
©
INTERNATIONAL STANDARD  ISO ISO 2286-3:1998(E)
Rubber- or plastics-coated fabrics — Determination of roll
characteristics —
Part 3:
Method for determination of thickness
WARNING – Persons using this part of ISO 2286 should be familiar with normal laboratory practice. This part
of ISO 2286 does not purport to address all of the safety problems, if any, associated with its use. It is the
responsibility of the user to establish appropriate safety and health practices and to ensure compliance with
any national regulatory conditions.
1 Scope
This part of ISO 2286 describes a method for
...