EN ISO 11403-1:2003

SLOVENSKI STANDARD
01-julij-2003
1DGRPHãþD
SIST EN ISO 11403-1:2000
3ROLPHUQLPDWHULDOL3UHGVWDYLWHYSULPHUOMLYLKSRGDWNRYSULGREOMHQLKYUD]OLþQLK
UD]PHUDKGHO0HKDQVNHODVWQRVWL,62
Plastics - Acquisition and presentation of comparable multipoint data - Part 1:
Mechanical properties (ISO 11403-1:2001)
Kunststoffe - Ermittlung und Darstellung von vergleichbaren Vielpunktkennwerten - Teil
1: Mechanische Eigenschaften (ISO 11403-1:2001)
Plastiques - Acquisition et présentation de données multiples comparables - Partie 1:
Propriétés mécaniques (ISO 11403-1:2001)
Ta slovenski standard je istoveten z: EN ISO 11403-1:2003
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 11403-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2003
ICS 83.080.01 Supersedes EN ISO 11403-1:2003
English version
Plastics - Acquisition and presentation of comparable multipoint
data - Part 1: Mechanical properties (ISO 11403-1:2001)
Plastiques - Acquisition et présentation de données Kunststoffe - Ermittlung und Darstellung vergleichbarer
multiples comparables - Partie 1: Propriétés mécaniques Vielpunktkennwerte - Teil 1: Mechanische Eigenschaften
(ISO 11403-1:2001) (ISO 11403-1:2001)
This European Standard was approved by CEN on 12 December 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovak Republic, Spain, Sweden, Switzerland and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11403-1:2003 E
worldwide for CEN national Members.

Foreword
The text of ISO 11403-1:2001 has been prepared by Technical Committee ISO/TC 61 "Plastics”
of the International Organization for Standardization (ISO) and has been taken over as EN ISO
11403-1:2003 by Technical Committee CEN/TC 249 "Plastics", the secretariat of which is held
by IBN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by September 2003, and conflicting national
standards shall be withdrawn at the latest by September 2003.
This document supersedes EN ISO 11403-1:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Slovak Republic, Spain, Sweden,
Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 11403-1:2001 has been approved by CEN as EN ISO 11403-1:2003 without any
modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 179-1 2000 Plastics - Determination of Charpy impact EN ISO 179-1 2000
properties - Part 1: Non-instrumented
impact test
ISO 179-2 1997 Plastics - Determination of Charpy impact EN ISO 179-2 1999
properties - Part 2: Instrumented impact
test
ISO 294-1 1996 Plastics - Injection moulding of test EN ISO 294-1 1998
specimens of thermoplastic materials - Part
1: General principles, and moulding of
multipurpose and bar test specimens
ISO 294-3 1996 Plastics - Injection moulding of test EN ISO 294-3 1998
specimens of thermoplastic materials - Part
3: Small plates
ISO 295 1991 Plastics - Compression moulding of test EN ISO 295 1998
specimens of thermosetting materials
ISO 527-1 1993 Plastics - Determination of tensile EN ISO 527-1 1996
properties - Part 1: General principles
ISO 527-2 1993 Plastics - Determination of tensile EN ISO 527-2 1996
properties - Part 2: Test conditions for
moulding and extrusion plastics
ISO 899-1 1993 Plastics - Determination of creep behaviour EN ISO 899-1 1996
- Part 1: Tensile creep
ISO 2818 1994 Plastics - Preparation of test specimens by EN ISO 2818 1996
machining
ISO 3167 1993 Plastics - Multipurpose-test specimens EN ISO 3167 1996
EN ISO 6603-2 2000
ISO 6603-2 2000 Plastics - Determination of puncture impact
behaviour of rigid plastics - Part 2:
Instrumented puncture test
ISO 6721-2 1994 Plastics - Determination of dynamic EN ISO 6721-2 1996
mechanical properties - Part 2: Torsion-
pendulum method
ISO 10724-1 1998 Plastics - Injection moulding of test EN ISO 10724-1 2001
specimens of thermosetting powder
moulding compounds (PMCs) - Part 1:
General principles and moulding of
multipurpose test specimens
ISO 10724-2 1998 Plastics - Injection moulding of test EN ISO 10724-2 2000
specimens of thermosetting powder
moulding compounds (PMCs) - Part 2:
Small plates
INTERNATIONAL ISO
STANDARD 11403-1
Second edition
2001-12-15
Plastics — Acquisition and presentation of
comparable multipoint data —
Part 1:
Mechanical properties
Plastiques — Acquisition et présentation de données multiples
comparables —
Partie 1: Propriétés mécaniques

Reference number
ISO 11403-1:2001(E)
©
ISO 2001
ISO 11403-1:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2001 – All rights reserved

ISO 11403-1:2001(E)
Contents Page
Foreword.iv
Introduction.v
1 Scope .1
2 Normative references.1
3 Term and definition .2
4 Specimen preparation.2
5 Conditioning.3
6 Test requirements.4
6.1 General.4
6.2 Dynamic modulus: ISO 6721-2 or ISO 6721-4.4
6.3 Tensile properties at constant test speed: ISO 527-1 and ISO 527-2.4
6.4 Tensile creep: ISO 899-1 .5
6.5 Charpy impact strength: ISO 179-1 or ISO 179-2 .5
6.6 Puncture impact behaviour: ISO 6603-2.6
7 Presentation of data .6
8 Precision.8
Annex A (informative) Other properties.12
A.1 General.12
A.2 Fracture-mechanics parameters .12
A.3 Fatigue .12
A.4 Creep rupture .12
Bibliography.13

ISO 11403-1:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 11403 may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11403-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 2, Mechanical
properties.
This second edition cancels and replaces the first edition (ISO 11403:1994), which has been technically revised.
ISO 11403 consists of the following parts, under the general title Plastics — Acquisition and presentation of
comparable multipoint data:
 Part 1: Mechanical properties
 Part 2: Thermal and processing properties
 Part 3: Environmental influences on properties
Annex A of this part of ISO 11403 is for information only.
iv © ISO 2001 – All rights reserved

ISO 11403-1:2001(E)
Introduction
This International Standard has been prepared because users of plastics find sometimes that available data cannot
be used readily to compare the properties of similar materials, especially when the data have been supplied by
different sources. Even when the
...