EN ISO 887:2000

SLOVENSKI STANDARD
SIST EN ISO 887:2002
01-julij-2002
Okrogle ravne podložke za metrske vijake in matice za splošno rabo - Splošni
pregled (ISO 887:2000)
Plain washers for metric bolts, screws and nuts for general purposes - General plan (ISO
887:2000)
Flache Scheiben für metrische Schrauben und Muttern für allgemeine Anwendungen -
Allgemeine Übersicht (ISO 887:2000)
Rondelles plates pour vis et écrous métriques pour usages généraux - Plan général (ISO
887:2000)
Ta slovenski standard je istoveten z: EN ISO 887:2000
ICS:
21.060.30 Podložke, varovalni elementi Washers, locking elements
SIST EN ISO 887:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 887:2002

---------------------- Page: 2 ----------------------

SIST EN ISO 887:2002

---------------------- Page: 3 ----------------------

SIST EN ISO 887:2002

---------------------- Page: 4 ----------------------

SIST EN ISO 887:2002

---------------------- Page: 5 ----------------------

SIST EN ISO 887:2002

---------------------- Page: 6 ----------------------

SIST EN ISO 887:2002
INTERNATIONAL ISO
STANDARD 887
Second edition
2000-06-15
Plain washers for metric bolts, screws and
nuts for general purposes — General plan
Rondelles plates pour vis et écrous métriques pour usages généraux —
Plan géneral
Reference number
ISO 887:2000(E)
©
ISO 2000

---------------------- Page: 7 ----------------------

SIST EN ISO 887:2002
ISO 887:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 887:2002
ISO 887:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 887 was prepared by Technical Committee ISO/TC 2, Fasteners.
This second edition cancels and replaces the first edition (ISO 887:1983), which has been technically revised.
Annex A of this International Standard is for information only.
© ISO 2000 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 887:2002

---------------------- Page: 10 ----------------------

SIST EN ISO 887:2002
INTERNATIONAL STANDARD ISO 887:2000(E)
Plain washers for metric bolts, screws and nuts for general
purposes — General plan
1 Scope
This International Standard specifies the full range of the nominal dimensions of product-grade-A and -C plain
washers
...