Unplasticized poly(vinyl chloride) (PVC-U) profiles for the fabrication of windows and doors - Classification, requirements and test methods - Part 1: Non-coated PVC-U profiles with light coloured surfaces

This European Standard specifies the classifications, requirements and test methods for non-coated unplasticized poly(vinyl chloride) (PVC-U) profiles with light coloured surfaces intended to be used for the fabrication of windows and doors.
It is applicable to PVC-U profiles with the colorimetric co-ordinates measured on the visible surfaces, as follows:
-   L* ≥ 82 (chromaticity co-ordinate Y ≥ 60),
-   -2,5 ≤ a* ≤ 5,
-   -5 ≤ b* ≤ 15.
NOTE 1   For editorial reasons in this document the term "window" is used for window/door.
NOTE 2   Profiles made from PVC-U materials with reinforcements (e.g. glass fibres) are not part of this scope.

Profile aus weichmacherfreiem Polyvinylchlorid (PVC-U) zur Herstellung von Fenstern und Türen - Klassifizierung, Anforderungen und Prüfverfahren - Teil 1: Nicht beschichtete PVC-U Profile mit hellen Oberflächen

Diese Europäische Norm legt die Klassifizierungen, Anforderungen an und Prüfverfahren für nicht beschichtete, helle Profile aus weichmacherfreiem Polyvinylchlorid (PVC-U) zur Herstellung von Fenstern und Türen fest.
Diese Norm gilt für PVC-U-Profile mit den folgenden Farbmaßzahlen, die auf sichtbaren Oberflächen gemessen wurden:
— L* ≥ 82 (Farbwertkoordinate Y ≥ 60),
— −2,5 ≤ a* ≤ 5,
— −5 ≤ b* ≤ 15.
ANMERKUNG 1 Aus redaktionellen Gründen wird in diesem Dokument die Benennung „Fenster“ für Fenster/Tür angewendet.
ANMERKUNG 2 Profile aus PVC-U-Materialien mit Verstärkungsstoffen (z. B. Glasfasern) liegen außerhalb dieses Anwendungsbereichs.

Profilés de poly(chlorure de vinyle) non plastifié (PVC-U) pour la fabrication des fenêtres et des portes — Classification, exigences et méthodes d’essai - Partie 1: Profilés en PVC-U non revêtus avec des faces de teinte claire

La présente Norme européenne spécifie les classifications, les exigences et les méthodes d’essai des profilés de poly(chlorure de vinyle) non plastifié (PVC U) non revêtus avec des faces de teinte claire destinés à être utilisés pour la fabrication des fenêtres et des portes.
Elle s’applique aux profilés en PVC U dont les coordonnées colorimétriques mesurées sur les surfaces visibles sont les suivantes :
-   L*  82 (coordonnée de chromaticité Y  60),
-   –2,5  a*  5,
-   –5  b*  15.
NOTE 1   Pour des raisons éditoriales, dans ce document le terme « fenêtre » est utilisé pour « fenêtre/porte ».
NOTE 2   Les profilés fabriqués à partir de matériau PVC U avec renforts (par exemple des fibres de verre) sont en dehors du présent domaine d’application.

Profili iz trdega polivinilklorida (PVC-U) za izdelavo oken in vrat - Razvrščanje, zahteve in preskusne metode - 1. del: Neprevlečeni PVC-U profili s svetlo površino

Ta del standarda EN 12608 določa razvrščanje, zahteve in preskusne metode za neprevlečene profile iz trdega polivinilklorida (PVC-U) s svetlo površino, ki so namenjeni za uporabo pri izdelavi oken in vrat. Uporablja se za profile iz trdega polivinilklorida s kolorimetričnimi koordinatami, izmerjenimi na vidni površini, kot je opisano v nadaljevanju: – L * 82 (kromatska koordinata Y 60) – –2,5 a* 5 – –5 b* 15 v skladu s standardi ISO 7724-1 [1], ISO 7724-2 [2] in ISO 7724-3 [3] ob uporabi standarda za vrsto svetlobe CIE D65, vključno z refleksijsko odbojnostjo in pogojem meritve 8/d ali d/8 (brez zadrževanja sijaja pri obeh), pri čemer je izbran 2-stopinjski ali 10-stopinjski vidni kot v skladu s standardom ISO 7724 1.

General Information

Status
Withdrawn
Publication Date
08-Mar-2016
Withdrawal Date
18-Aug-2020
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
19-Aug-2020

Relations

Buy Standard

Standard
EN 12608-1:2016
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Profile aus weichmacherfreiem Polyvinylchlorid (PVC-U) zur Herstellung von Fenstern und Türen - Klassifizierung, Anforderungen und Prüfverfahren - Teil 1: Nicht beschichtete PVC-U Profile mit hellen OberflächenProfilés de poly(chlorure de vinyle) non plastifié (PVC-U) pour la fabrication des fenêtres et des portes — Classification, exigences et méthodes d’essai - Partie 1: Profilés en PVC-U non revêtus avec des faces de teinte claireUnplasticized poly(vinyl chloride) (PVC-U) profiles for the fabrication of windows and doors - Classification, requirements and test methods - Part 1: Non-coated PVC-U profiles with light coloured surfaces91.060.50Vrata in oknaDoors and windows83.140.99Drugi izdelki iz gume in polimernih materialovOther rubber and plastics productsICS:Ta slovenski standard je istoveten z:EN 12608-1:2016SIST EN 12608-1:2016en01-maj-2016SIST EN 12608-1:2016SLOVENSKI
STANDARDSIST EN 12608:20031DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12608-1
March
t r s x ICS
z uä s v rä { {â
{ sä r x rä w r Supersedes EN
s t x r zã t r r uEnglish Version
fabrication of windows and doors æ Classificationá requirements and test methods æ Part
sã Nonæcoated PVCæU profiles with light coloured surfaces Classificationá exigences et méthodes d 5essai æ Partie
sã Profilés en PVCæU non revêtus avec des faces de teinte claire Klassifizierungá Anforderungen und Prüfverfahren æ Teil
sã Nicht beschichtete PVCæU Profile mit hellen Oberflächen This European Standard was approved by CEN on
s w January
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey andUnited Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s x CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s t x r zæ sã t r s x ESIST EN 12608-1:2016

European foreword . 4 1 Scope . 6 2 Normative references . 6 3 Terms and definitions . 7 3.1 General . 7 3.2 Profile definitions . 7 3.3 Geometrical definitions . 8 3.4 Material definitions . 9 4 Classifications . 10 4.1 General . 10 4.2 Classification of climatic zones. 10 4.3 Classification of main profiles according to the resistance to impact by falling mass . 11 4.4 Classification of main profiles according to the wall thickness of the external walls . 11 5 Requirements . 13 5.1 Material . 13 5.1.1 UV resistant virgin material . 13 5.1.2 Non-UV resistant virgin material . 13 5.1.3 Reprocessed, recycled materials and non-UV resistant virgin materials . 13 5.2 Appearance . 14 5.3 Dimensions and tolerances . 14 5.3.1 General . 14 5.3.2 Nominal shape . 14 5.3.3 Wall thickness of main profiles . 14 5.3.4 Tolerances on other dimensions . 15 5.3.5 Deviation from straightness of the main profiles . 15 5.4 Linear weight of the main profiles . 15 5.5 Heat reversion . 15 5.5.1 Main profile . 15 5.5.2 Auxiliary profiles . 15 5.6 Resistance to impact of main profiles by falling mass . 16 5.7 Behaviour after heating at 150 °C . 16 5.8 Charpy impact resistance of main profile . 16 5.9 Resistance to weathering . 16 5.9.1 Exposure procedure . 16 5.9.2 Impact strength after artificial weathering of main profiles . 17 5.9.3 Colour fastness . 17 5.10 Strength of welded corners and T-joints of main profiles . 17 5.10.1 Test method . 17 5.10.2 Tensile bending test . 17 5.10.3 Compression bending test . 17 6 Test methods . 17 6.1 Determination of the appearance . 17 6.2 Determination of dimensions . 18 6.2.1 Measuring devices . 18 SIST EN 12608-1:2016

Material characteristics, preparation of samples and requirements . 21 A.1 General . 21 A.2 Test specimens . 21 A.3 Preparation of pressed plates . 21 A.4 Material characteristics . 21 A.4.1 Vicat softening temperature . 21 A.4.2 Flexural modulus of elasticity . 22 A.4.3 Tensile impact strength . 22 A.5 Test report . 22 Annex B (normative)
Calculation method for the determination of the radiant exposure and exposure time to be used for artificial weathering. 23 B.1 General . 23 B.2 Calculation. 23
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.