Earth-moving machinery - Safety - Part 8: Requirements for graders

This part of EN 474 deals with all significant hazards, hazardous situations and events relevant to graders as defined in EN ISO 6165:2006, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).
This part also deals with graders equipped with attached snowplough.
The requirements of this part are complementary to the common requirements formulated in EN 474-1:2006.
This part does not repeat the requirements from EN 474-1:2006, but adds or replaces the requirements for application for graders.
This part specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards, hazardous situations and events during commissioning, operation and maintenance of graders.
This European Standard is not applicable to graders manufactured before the date of publication of this European Standard by CEN.
NOTE   When graders are intended for use in winter service, see EN 13021:2003 :Winter service machines - Safety requirements

Erdbaumaschinen - Sicherheit - Teil 8: Anforderungen für Grader

Dieser Teil der EN 474 behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse,
die auf Grader, wie in EN ISO 6165:2006 definiert, zutreffen, wenn sie bestimmungsgemäß
verwendet werden. Die nach vernünftigem Ermessen für den Hersteller vorhersehbare Nutzung der Maschine
außerhalb der bestimmungsgemäßen Verwendung ist ebenfalls berücksichtigt (siehe Abschnitt 4).
Dieser Teil behandelt auch Grader, welche mit Schneeräumschild ausgerüstet sind.
Die Anforderungen gelten ergänzend zu den allgemeinen Anforderungen der !EN 474-1:2006+A1:2009".
Dieser Teil wiederholt nicht die Anforderungen der !EN 474-1:2006+A1:2009", aber ergänzt oder ersetzt
diese für den Einsatz von Gradern.
Dieser Teil beschreibt die geeigneten technischen Maßnahmen, die erforderlich sind, die Risiken, die
aufgrund signifikanter Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die während der
Inbetriebnahme, des Betriebs, der Instandhaltung von Gradern eintreten können, zu beseitigen oder zu
mindern.
Diese Europäische Norm ist nicht anzuwenden für Grader, die vor der Veröffentlichung dieser Europäischen
Norm durch CEN hergestellt wurden.
ANMERKUNG Für Grader, die im Winterdienst eingesetzt werden, siehe EN 13021:2003 Maschinen für den
Winterdienst  Sicherheitsanforderungen.

Engins de terrassement - Sécurité - Partie 8 : Prescriptions applicables aux niveleuses

La présente partie de l’EN 474 traite de tous les phénomènes, situations et événements dangereux significatifs relatifs aux niveleuses telles que définies dans l’EN ISO 6165:2006, lorsqu’elles sont utilisées comme prévu ou dans des conditions de mauvais usage que le fabricant peut raisonnablement prévoir (voir Article 4).
La présente partie traite également des niveleuses équipées en chasse-neige.
Les prescriptions figurant dans la présente partie viennent en complément des prescriptions communes présentées dans l’EN 474-1:2006+A1:2009.
La présente partie ne répète pas les prescriptions de l’EN 474-1:2006+A1:2009 mais en ajoute ou en remplace certaines applicables aux niveleuses.
La présente partie prescrit les mesures techniques appropriées pour éliminer ou réduire les risques dus aux phénomènes, situations et événements dangereux significatifs survenant lors de la mise en service, du fonctionnement et de la maintenance des niveleuses.
La présente Norme européenne n’est pas applicable aux niveleuses fabriquées avant la publication de la présente Norme européenne par le CEN.
NOTE   Lorsque des niveleuses sont conçues pour être utilisées pour le service hivernal, voir l’EN 13021:2003 «Machines pour le service hivernal  - Prescriptions de sécurité».

Stroji za zemeljska dela - Varnost - 8. del: Zahteve za grederje

General Information

Status
Withdrawn
Publication Date
10-Feb-2009
Withdrawal Date
29-Mar-2022
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
30-Mar-2022

Relations

Buy Standard

Standard
EN 474-8:2007+A1:2009
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-maj-2009
Stroji za zemeljska dela - Varnost - 8. del: Zahteve za grederje
Earth-moving machinery - Safety - Part 8: Requirements for graders
Erdbaumaschinen - Sicherheit - Teil 8: Anforderungen für Grader
Engins de terrassement - Sécurité - Partie 8 : Prescriptions applicables aux niveleuses
Ta slovenski standard je istoveten z: EN 474-8:2006+A1:2009
ICS:
53.100 Stroji za zemeljska dela Earth-moving machinery
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 474-8:2006+A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2009
ICS 53.100 Supersedes EN 474-8:2006
English Version
Earth-moving machinery - Safety - Part 8: Requirements for
graders
Engins de terrassement - Sécurité - Partie 8: Prescriptions Erdbaumaschinen - Sicherheit - Teil 8: Anforderungen für
applicables aux niveleuses Grader
This European Standard was approved by CEN on 17 April 2006 and includes Amendment 1 approved by CEN on 20 December 2008.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 474-8:2006+A1:2009: E
worldwide for CEN national Members.

Contents Page
Foreword .3
Introduction .4
1 Scope .5
2 Normative references .5
3 Terms and definitions .5
4 List of additional significant hazards .6
5 Safety requirements and/or measures .6
5.1 General .6
5.2 Operator’s position .6
5.3 Fenders .6
5.4 Steering system .6
6 Information for use .7
Annex A (normative) List of additional significant hazards – Graders .8
Annex B (informative) Illustrations .9
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC . 10
Annex ZB (informative) !!!!Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC"""" . 11
Bibliography . 12

Figures
Figure B.1 — Articulated steered grader . 9
Figure B.2 — Wheel steered grader . 9
Figure B.3 — Grader with snowblower . 9

Tables
Table A.1 — List of additional significant hazards . 8

Foreword
This document (EN 474-8:2006+A1:2009) has been prepared by Technical Committee CEN/TC 151
“Construction equipment and building material machines — Safety”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2009, and conflicting national standards shall be withdrawn at
the latest by December 2009.
This document includes Amendment 1, approved by CEN on 2008-12-20.
This document supersedes !EN 474-8:2006".
The start and finish of text introduced or altered by amendment is indicated in the text by tags ! ".
!For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document."
For bibliographic references, see !EN 474-1:2006+A1:2009".
EN 474 "Earth-moving machinery — Safety" comprises the following parts:
 Part 1: General requirements
 Part 2: Requirements for tractor-dozers
 Part 3: Requirements for loaders
 Part 4: Requirements for backhoe-loaders
 Part 5: Requirements for hydraulic excavators
 Part 6: Requirements for dumpers
 Part 7: Requirements for scrapers
 Part 8: Requirements for graders
 Part 9: Requirements for pipelayers
 Part 10: Requirements for trenchers
 Part 11: Requirements for earth and landfill compactors
 Part 12: Requirements for cable excavators.
This European Standard is intended for use in combination with Part 1 of the series.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and United Kingdom.
Introduction
This part of EN 474 is a type C standard as stated in EN ISO 12100-1:2003.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered are
indicated in the scope of this European Standard.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of the other standards, for machines
that have been designed and built according to the provisions of this type C standard.
1 Scope
This part of EN 474 deals with all significant hazards, hazardous situations and events relevant to graders as
defined in EN ISO 6165:2006, when they are used as intended and
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.