EN 4473:2010

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.VSHFLILNDFLMDLuft- und Raumfahrt - Aluminium pigmenttete Beschichtungen für Fixierungen - Technische LieferbedingungenSérie aérospatiale - Revêtements alumino-organiques pour fixations - Spécification techniqueAerospace series - Aluminium pigmented coatings for fasteners - Technical specification49.040Prevleke in z njimi povezani postopki, ki se uporabljajo v letalski in vesoljski industrijiCoatings and related processes used in aerospace industry49.030.01Vezni elementi na splošnoFasteners in general49.025.20AluminijAluminiumICS:Ta slovenski standard je istoveten z:EN 4473:2010SIST EN 4473:2010en01-december-2010SIST EN 4473:2010SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4473
September 2010 ICS 49.040 English Version
Aerospace series - Aluminium pigmented coatings for fasteners - Technical specification
Série aérospatiale - Revêtements alumino-organiques pour fixations - Spécification technique
Luft- und Raumfahrt - Aluminium pigmenttete Beschichtungen für Fixierungen - Technische Lieferbedingungen This European Standard was approved by CEN on 5 May 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4473:2010: ESIST EN 4473:2010

Test coupons for paint adhesion test . 12Annex B (normative)
Test specimen for ohmic resistance measurement . 13Annex C (normative)
Lightning current simulation and swept lightning . 14C.1 Lightning current simulation . 14C.2 Test specimens distribution . 14C.3 Swept lightning (on countersunk head fastener) . 14C.3.1 Current waveforms . 14C.3.2 Test method . 15C.3.3 Specimens . 15C.4 Lightning current transfer condition (on protruding head fastener) . 15C.4.1 Current waveforms . 15C.4.2 Test method . 16 SIST EN 4473:2010

Type I : Coating with chromate and a cetyl alcohol lubricant. Type II : Coating without chromate and an cetyl alcohol lubricant.
Type III : Coating with chromate, no additional lubricant. Type IV : Coating without chromate, no additional lubricant. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2409, Paints and varnishes — Cross-cut test ISO 9227, Corrosion tests in artificial atmospheres — Salt spray tests EN ISO 2812-1, Paints and varnishes — Determination of resistance to liquids — Part 1: Immersion in liquids other than water (ISO 2812-1:2007) EN 4474, Aerospace series — Aluminium pigmented coatings — Coating methods EN 6117, Specification for bolts with cetyl alcohol 2)
EN 9133, Aerospace series — Quality management systems — Qualification Procedure for Aerospace Standards Parts TR 4676, Aluminium pigmented coatings — List of commercial products 3) NASM 1312-5, Fastener Test Methods; Method 5: Stress durability 4) NASM 1312-12, Fasteners Test Methods, Method 12: Thickness of metallic coatings 4) MIL-A-8625, Anodic coatings for aluminium and aluminium alloys 5)
1) Maximum operating temperature. 2) Published as ASD Prestandard at the date of publication of this standard. 3) Published as ASD Technical Report at the date of publication of this standard. 4) Published by: Aerospace Industries Association, 1000 Wilson Boulevard, Suite 1700, Arlington, VA 22209-3928, USA. 5) Published by: Department of Defense (DOD), the Pentagon, Washington, D.C. 20301 USA. SIST EN 4473:2010
...