ASTM F2019-22
(Practice)Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic Cured-in-Place (GRP-CIPP) Using the UV-Light Curing Method
Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic Cured-in-Place (GRP-CIPP) Using the UV-Light Curing Method
SIGNIFICANCE AND USE
4.1 This practice is for use by designers and specifiers, regulatory agencies, owners and inspection organizations who are involved in the rehabilitation of conduits through the use of a resin-impregnated glass fiber tube, pulled in place through an existing pipe or conduit, subsequently inflated and then cured by a designed exposure to UV-light. As for any standard practice, modifications may be required for specific job conditions.
SCOPE
1.1 This practice covers the procedures for the reconstruction of pipelines and conduits (4 in. to 72 in. (100 mm to 1830 mm) diameter) by the pulled-in place installation of a resin-impregnated, glass fiber tube into an existing pipe or conduit followed by its inflation with compressed air pressure (see Fig. 1) to expand it firmly against the wall surface of the host structure. The photo-initiated resin system in the tube is then cured by exposure to ultraviolet (UV) light. When cured, the finished cured-in-place pipe will be a continuous and tight fitting pipe within a pipe. This type of reconstruction process can be used in a variety of gravity flow applications such as sanitary sewers, storm sewers, process piping, electrical conduits, and ventilation systems.
FIG. 1 UV Cured-In-Place Pipe Installation Method (Air/Steam)
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F2019 − 22
Standard Practice for
Rehabilitation of Existing Pipelines and Conduits by the
Pulled in Place Installation of Glass Reinforced Plastic
Cured-in-Place (GRP-CIPP) Using the UV-Light Curing
1
Method
This standard is issued under the fixed designation F2019; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
2.1 ASTM Standards:
1.1 This practice covers the procedures for the reconstruc-
C1920Practice for Cleaning of Vitrified Clay Sanitary
tion of pipelines and conduits (4in. to 72 in. (100mm to 1830
Sewer Pipelines
mm) diameter) by the pulled-in place installation of a resin-
D543Practices for Evaluating the Resistance of Plastics to
impregnated, glass fiber tube into an existing pipe or conduit
Chemical Reagents
followedbyitsinflationwithcompressedairpressure(seeFig.
D578Specification for Glass Fiber Strands
1) to expand it firmly against the wall surface of the host
D790Test Methods for Flexural Properties of Unreinforced
structure. The photo-initiated resin system in the tube is then
and Reinforced Plastics and Electrical Insulating Materi-
cured by exposure to ultraviolet (UV) light. When cured, the
als
finished cured-in-place pipe will be a continuous and tight
D1600TerminologyforAbbreviatedTermsRelatingtoPlas-
fitting pipe within a pipe. This type of reconstruction process
tics
can be used in a variety of gravity flow applications such as
D2990Test Methods forTensile, Compressive, and Flexural
sanitary sewers, storm sewers, process piping, electrical
Creep and Creep-Rupture of Plastics
conduits, and ventilation systems.
D3567PracticeforDeterminingDimensionsof“Fiberglass”
1.2 The values stated in inch-pound units are to be regarded
(Glass-Fiber-Reinforced Thermosetting Resin) Pipe and
as standard. The values given in parentheses are mathematical
Fittings
conversions to SI units that are provided for information only
D5813 Specification for Cured-In-Place Thermosetting
and are not considered standard.
Resin Sewer Piping Systems
1.3 This standard does not purport to address all of the F412Terminology Relating to Plastic Piping Systems
safety concerns, if any, associated with its use. It is the F1216Practice for Rehabilitation of Existing Pipelines and
responsibility of the user of this standard to establish appro- Conduits by the Inversion and Curing of a Resin-
priate safety, health, and environmental practices and deter- Impregnated Tube
mine the applicability of regulatory limitations prior to use. F1417Practice for Installation Acceptance of Plastic Non-
pressure Sewer Lines Using Low-Pressure Air
1.4 This international standard was developed in accor-
3
dance with internationally recognized principles on standard-
2.2 ISO Standards:
ization established in the Decision on Principles for the
11296-4Plastics piping systems for renovation of under-
Development of International Standards, Guides and Recom-
ground non-pressure drainage and sewerage networks –
mendations issued by the World Trade Organization Technical
Part 4: Lining with cured-in-place pipes
Barriers to Trade (TBT) Committee.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
1
This practice is under the jurisdiction of ASTM Committee F17 on Plastic contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Piping Systems and is the direct responsibility of Subcommittee F17.67 on Standards volume information, refer to the standard’s Document Summary page on
Trenchless Plastic Pipeline Technology. the ASTM website.
3
Current edition approved Nov. 15, 2022. Published December 2022. Originally Available from International Organization for Standardization (ISO), ISO
approved in 2000. Last previous edition approved in 2020 as F2019–20. DOI: Central Secretariat, BIBC II, Chemin de Blandonnet 8, CP 401, 1214 Vernier,
10.1520/F2019-22. Geneva, Switzerland, http://www.iso.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2019 − 22
FIG. 1 UV Cured-In-Place Pipe Installation Method (Air/Steam)
2
---------------------- Page: 2 ----------------------
F2019 − 22
7685Plastics piping systems – Glass-reinforced thermoset- sliding resistance and to protect the uncured resin saturated
ting plastics (GRP) pipes – Det
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2019 − 20 F2019 − 22
Standard Practice for
Rehabilitation of Existing Pipelines and Conduits by the
Pulled in Place Installation of Glass Reinforced Plastic
Cured-in-Place (GRP-CIPP) Using the UV-Light Curing
1
Method
This standard is issued under the fixed designation F2019; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This practice covers the procedures for the reconstruction of pipelines and conduits (4(4 in. to 72 in. (100(100 mm to 1830
mm) diameter) by the pulled-in place installation of a resin-impregnated, glass fiber tube into an existing pipe or conduit followed
by its inflation with compressed air pressure (see Fig. 1) to expand it firmly against the wall surface of the host structure. The
photo-initiated resin system in the tube is then cured by exposure to ultraviolet (UV) light. When cured, the finished cured-in-place
pipe will be a continuous and tight fitting pipe within a pipe. This type of reconstruction process can be used in a variety of gravity
flow applications such as sanitary sewers, storm sewers, process piping, electrical conduits, and ventilation systems.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
C1920 Practice for Cleaning of Vitrified Clay Sanitary Sewer Pipelines
D543 Practices for Evaluating the Resistance of Plastics to Chemical Reagents
D578 Specification for Glass Fiber Strands
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2990 Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
D3567 Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
D5813 Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
1
This practice is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.67 on Trenchless Plastic
Pipeline Technology.
Current edition approved Jan. 1, 2020Nov. 15, 2022. Published March 2020December 2022. Originally approved in 2000. Last previous edition approved in 20112020
as F2019 – 11.F2019 – 20. DOI: 10.1520/F2019-20.10.1520/F2019-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2019 − 22
FIG. 1 UV Cured-In-Place Pipe Installation Method (Air/Steam)
2
---------------------- Page: 2 ----------------------
F2019 − 22
F412 Terminology Relating to Plastic Piping Systems
F1216 Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
F1417 Practice for Installation Acceptance of Plastic Non-pressure Sewer Lines Using Low-Pressure Air
3
2.2 ISO Standards:
11296-4 Plastics piping systems for renovation of under-ground non-pressure drainage and sewerage networks – Part 4: Lining
with cured-in-place pipes
7685 Plastics piping systems – Glass-reinforced thermosetting plastics (GRP) pipes – Determination of initial specific ring
stiffnes
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.