iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D4547-03

(Practice)

Standard Guide for Sampling Waste and Soils for Volatile Organic Compounds

Standard Guide for Sampling Waste and Soils for Volatile Organic Compounds

SCOPE
1.1 This guide describes recommended procedures for the collection, handling, and preparation of solid waste, soil, and sediment samples for subsequent determination of volatile organic compounds (VOCs). This class of compounds includes low molecular weight aromatics, hydrocarbons, halogenated hydrocarbons, ketones, acetates, nitriles, acrylates, ethers, and sulfides with boiling points below 200° Celsius (C) that are insoluble or slightly soluble in water.
1.2 Methods of sample collection, handling, storage, and preparation for analysis are described.
1.3 This guide does not cover the details of sampling design, laboratory preparation of containers, and the analysis of the samples.
1.4 It is recommended that this guide be used in conjunction with Guide D 4687.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 7.2 and 8.1.1 for specific warnings.

General Information

Status
Historical
Publication Date
09-Jun-2003
ICS
13.080.05 - Examination of soils in general
Technical Committee
D34 - Waste Management
Drafting Committee
D34.01.02 - Sampling Techniques
Current Stage
Ref Project

Relations

Replaces
ASTM D4547-98 - Standard Guide for Sampling Waste and Soils for Volatile Organic Compounds
Effective Date
10-Jun-2003
Replaced By
ASTM D4547-06 - Standard Guide for Sampling Waste and Soils for Volatile Organic Compounds
Effective Date
01-Feb-2006
Referred By
ASTM D6044-21 - Standard Guide for Representative Sampling for Management of Waste and Contaminated Media
Effective Date
10-Jun-2003
Referred By
ASTM D5681-22e1 - Standard Terminology for Waste and Waste Management
Effective Date
10-Jun-2003
Referred By
ASTM D6051-15(2023) - Standard Guide for Composite Sampling and Field Subsampling for Environmental Waste Management Activities
Effective Date
10-Jun-2003
Referred By
ASTM D6907-22 - Standard Practice for Sampling Soils and Contaminated Media with Hand-Operated Bucket Augers
Effective Date
10-Jun-2003
Referred By
ASTM D6640-21 - Standard Practice for Collection and Handling of Soils Obtained in Core Barrel Samplers for Environmental Investigations
Effective Date
10-Jun-2003
Referred By
ASTM D6323-19 - Standard Guide for Laboratory Subsampling of Media Related to Waste Management Activities
Effective Date
10-Jun-2003
Referred By
ASTM E1963-22 - Standard Guide for Conducting Terrestrial Plant Toxicity Tests
Effective Date
10-Jun-2003
Referred By
ASTM D6232-21 - Standard Guide for Selection of Sampling Equipment for Waste and Contaminated Media Data Collection Activities
Effective Date
10-Jun-2003
Referred By
ASTM D7204-15 - Standard Practice for Sampling Waste Streams on Conveyors
Effective Date
10-Jun-2003
Referred By
ASTM D5679-16 - Standard Practice for Sampling Consolidated Solids in Drums or Similar Containers
Effective Date
10-Jun-2003
Referred By
ASTM D5830-22 - Standard Test Method for Solvents Analysis in Hazardous Waste Using Gas Chromatography
Effective Date
10-Jun-2003
Referred By
ASTM D6009-19 - Standard Guide for Sampling Waste Piles
Effective Date
10-Jun-2003
Referred By
ASTM D8170-20 - Standard Guide for Using Disposable Handheld Soil Core Samplers for the Collection and Storage of Soil for Volatile Organic Analysis
Effective Date
10-Jun-2003

Buy Standard

ASTM D4547-03 - Standard Guide for Sampling Waste and Soils for Volatile Organic CompoundsASTM D4547-03 - Standard Guide for Sampling Waste and Soils for Volatile Organic Compounds
PreviousNext
Standard
ASTM D4547-03 - Standard Guide for Sampling Waste and Soils for Volatile Organic Compounds
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D4547–03
Standard Guide for
1
Sampling Waste and Soils for Volatile Organic Compounds
This standard is issued under the fixed designation D 4547; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope Data Quality Objectives
D 6051 Guide for Composite Sampling and Field Subsam-
1.1 This guide describes recommended procedures for the
pling for Environmental Waste Management Activities
collection, handling, and preparation of solid waste, soil, and
D 6418 Practice for Using the Disposable En Core Sampler
sediment samples for subsequent determination of volatile
for Sampling and Storing Soil for Volatile OrganicAnaly-
organic compounds (VOCs).This class of compounds includes
sis
low molecular weight aromatics, hydrocarbons, halogenated
D 6640 Practice for Collection and Handling of Soils Ob-
hydrocarbons, ketones, acetates, nitriles, acrylates, ethers, and
tained in Core Barrel Samplers for Enviromental Investi-
sulfides with boiling points below 200° Celsius (C) that are
gations
insoluble or slightly soluble in water.
E 856 Definitions of Terms and Abbreviations Relating to
1.2 Methods of sample collection, handling, storage, and
Physical and Chemical Characteristics of Refuse-Derived
preparation for analysis are described.
Fuel
1.3 Thisguidedoesnotcoverthedetailsofsamplingdesign,
2.2 Federal Standard:
laboratory preparation of containers, and the analysis of the
Title 49 Transportation, Code of Federal Regulations
samples.
(CFR), Part 172, List of Hazardous Substances and
1.4 Itisrecommendedthatthisguidebeusedinconjunction
3
Reportable Quantities
with Guide D 4687.
1.5 This standard does not purport to address all of the
3. Terminology
safety concerns, if any, associated with its use. It is the
3.1 sample, n—a portion of material taken from a larger
responsibility of the user of this standard to establish appro-
quantity for the purpose of estimating properties or composi-
priate safety and health practices and determine the applica-
tion of the larger quantity. (E 856)
bility of regulatory limitations prior to use. See 7.2 and 8.1.1
3.2 subsample, n—a portion of a sample taken for the
for specific warnings.
purpose of estimating properties or composition of the whole
2. Referenced Documents sample. (D 6051)
2
3.2.1 Discussion—A subsample, by definition, is also a
2.1 ASTM Standards:
sample.
D 3550 Practice for Thick Wall Ring-Lined, Split Barrel,
Drive Sampling of Soils
4. Summary of Guide
D 4687 Guide for General Planning of Waste Sampling
4.1 This guide addresses the use of tools for sample collec-
D 4700 Guide for Soil Sampling from the Vadose Zone
tion and transfer, conditions for sample storage, sample pres-
D 5058 Test Methods for Compatibility of Screening
ervation, and two common means of sample preparation for
Analysis of Waste
analysis. Special attention is given to each step from sample
D 5792 Practice for Generation of Environmental Data
collectiontoanalysistolimitthelossofVOCsbyvolatilization
Related to Waste ManagementActivities: Development of
and biodegradation. The sample collected and analyzed should
be representative of the matrix material sampled. The two
1
This guide is under the jurisdiction of ASTM Committee D34 on Waste methods cited for the preparation of samples for VOC analysis
Management and is the direct responsibility of Subcommittee D34.01.02 on
are methanol extraction and vapor partitioning (that is, purge-
Monitoring.
and-trapandheadspace).Themethodofsamplepreparationfor
Current edition approved June 10, 2003. Published August 2003. Originally
approved in 1991. Last previous edition approved in 1998 as D 4547 - 98.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from Superintendent of Documents, U.S. Government Printing
the ASTM website. Office, Washington, DC 20402.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D4547–03
VOC analysis should be consistent with the data quality 6.1.1 Sample collection, handling, and preservation meth-
objectives (see Practice D 5792). ods should be compatible with the method used to prepare the
sample for VOC analysis, and meet the project’s data quality
5. Significance and Use
objectives (see Practice D 5792). Preparation of a sample for
5.1 This guide describes sample collection and handling
instrumental an
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D4646-16(2023)(Test Method)
Standard Test Method for 24 h Batch-Type Measurement of Contaminant Sorption by Soils and Sediments

SIGNIFICANCE AND USE
5.1 This test method is meant to allow for a rapid (24 h) index of a geomedia's sorption affinity for given solutes in environmental waters or leachates. A large number of samples may be run in parallel using this test method to determine a comparative ranking of those samples, based upon the amount of solute sorbed by the geomedia, or by various geomedia or leachate constituents. The 24 h time is used to make the test convenient and also to minimize microbial, light, or hydrolytic degradation which may be a problem in longer timed procedures. While Kd values are directly applicable for screening and comparative ranking purposes, their use in predictive field applications generally requires the assumption that Kd be a fixed value.  
5.2 While this test method may be useful in determining 24 h Kd values for nonvolatile organic constituents, interlaboratory testing has been carried out only for the nonvolatile inorganic species arsenic and cadmium (see Section 12). However, the procedure has been tested for single-laboratory precision with polychlorinated biphenyls (PCBs) and is believed to be useful for all stable and nonvolatile inorganic and organic constituents. This test method is not considered appropriate for volatile constituents.  
5.3 The 24 h time limit may be sufficient to reach a steady-state Kd; however, the calculated Kd value should be considered a non-equilibrium measurement unless steady-state has been determined. To report this determination as a steady-state Kd, this test method should be conducted for intermediate times (for example, 12, 18, and 22 h) to ensure that the soluble concentrations in the solution have reached a steady state by 24 h. If a test duration of greater than 24 h is required, refer to Test Method D4319 for an alternate procedure of longer duration.
SCOPE
1.1 This test method describes a procedure for determining the sorption affinity of waste solutes by unconsolidated geologic material in aqueous suspension. The waste solute may be derived from a variety of sources such as wells, underdrain systems, or laboratory solutions such as those produced by waste extraction tests like the Practice D3987 shake extraction method.  
1.2 This test method is applicable in screening and providing relative rankings of a large number of geomedia samples for their sorption affinity in aqueous leachate/geomedia suspensions. This test method may not simulate sorption characteristics that would occur in unperturbed geologic settings.  
1.3 While this procedure may be applicable to both organic and inorganic constituents, care must be taken with respect to the stability of the particular constituents and their possible losses from solution by such processes as degradation by microbes, light, hydrolysis, or sorption to material surfaces. This test method should not be used for volatile chemical constituents (see 6.1).  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D6907-22(Practice)
Standard Practice for Sampling Soils and Contaminated Media with Hand-Operated Bucket Augers

SIGNIFICANCE AND USE
5.1 Bucket augers (Fig. 1) are relatively inexpensive, readily available, available in different types depending on the media to be sampled, and most can be easily operated by one person. They collect a reasonably cylindrical but disturbed sample of surface or subsurface soil or waste. They are generally not suited for sampling gravelly or coarser soil and are unsuitable for sampling rock. There are other designs of hand augers, such as the Edelman auger, used to retrieve difficult materials such as waste, sands, peat, and mud.
FIG. 1 Bucket Auger  
5.2 Bucket augers are commonly used equipment because they are inexpensive to operate, especially compared to powered equipment (that is, direct push and drill rigs). When evaluated against screw augers (Guide D4700), bucket augers generally collect larger samples with less chance of mixing with soil from shallow depths because the sample is retained within the auger bucket. Bucket augers are commonly used to depths of 3 m but have been used to much greater depths depending upon the soil or waste characteristics. In general, bucket augers can maintain open holes in unsaturated soils and saturated clay soils below the water table. Saturated sands will cave below the water table and perched zones and cohesionless dry sands may also cave. The sampling depth is limited by the force required to rotate the auger and the depth at which the bore hole collapses (unless bore casings or liners are used).  
5.3 Bucket augers may not be suitable for the collection of samples for determination of volatile organic compounds (VOCs) because the sample is disturbed and exposed to atmosphere during the collection process, which may lead to losses resulting in a chemically unrepresentative sample.  
5.4 If VOC analysis is required, the bucket auger is used to reach the desired sample depth, a planer auger can be used to clean the base of the hole, and a hammered drive tube sampler (Fig. 2) can be used at the bottom of the hole. Drive ...
SCOPE
1.1 This practice describes the procedures and equipment used to collect surface and subsurface soil and contaminated media samples for chemical analysis using a hand-operated bucket auger (sometimes referred to as a barrel auger). Several types of bucket augers exist and are designed for sampling various types of soil. All bucket augers collect disturbed samples. Bucket augers can also be used to auger to the desired sampling depth and then, using a core-type sampler, collect a relatively undisturbed sample suitable for chemical analysis.  
1.2 This practice does not cover the use of large 300 mm or greater diameter bucket augers mechanically operated by large drill rigs or similar equipment, such as those described in Practice D1452/D1452M, paragraph 5.2.4. Practice D1452/D1452M on auger borings refers to this hand auger included in Practice D6907 as a barrel auger.  
1.3 Refer to Guides D4700 and D6232 for information on other hand samplers. The bucket auger is often used for shallow surface soil sampling, but there are many other types of handheld augers, flight, screw, rotary powered, and agricultural push tube samplers. Practice D1452/D1452M addresses larger powered solid stem flight auger systems.  
1.4 This standard does not address soil samples obtained with mechanical drilling, direct push, and sonic machines (refer to Guides D6286/D6286M and D6169/D6169M) or for collecting cores from submerged sediments (Guide D4823).  
1.5 This practice does not address sampling objectives (see Practice D5792), general sample planning (see Guide D4687), and sampling design (for example, where to collect samples and what depth to sample (see Guide D6044)). Sampling for volatile organic compounds (see Guide D4547), equipment cleaning and decontamination (see Practice D5088), sample handling after collection such as compositing and subsampling (see Guide D6051), and sample preservation (Guide D4220/D4220M) are used in this s...

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D5633-21(Practice)
Standard Practice for Sampling with a Scoop

SIGNIFICANCE AND USE
5.1 This practice is intended for use in collecting samples of contaminated soils and similar materials.  
5.2 Scoops are used primarily for collecting samples near the surface. Subsurface samples can be obtained by first removing higher layers using a shovel or other suitable equipment and collecting the sample with the scoop.  
5.3 Because of their simplicity, scoops are useful in taking samples of waste materials where decontamination or disposal is a problem with other types of sampling equipment. Scoops are also suitable for use in rapid screening programs, pilot studies, and other semi-quantitative investigations.  
5.4 Samples should be collected in accordance with an appropriate work plan (see Practice D5283 and Guide D4687).
SCOPE
1.1 This practice covers the method and equipment used to collect surface and near-surface samples of soils and physically similar materials using a scoop.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D4547-20(Guide)
Standard Guide for Sampling Waste and Soils for Volatile Organic Compounds

SIGNIFICANCE AND USE
5.1 This guide describes sample collection and handling procedures designed to minimize losses of VOCs. The principal mechanisms for the loss of VOCs from materials during collection, handling, and storage are volatilization and biodegradation. Susceptibility of various VOCs to these two loss mechanisms is both compound and matrix specific. In general, compounds with higher vapor pressures are more susceptible to volatilization than compounds with lower vapor pressures. Also, aerobically degradable compounds are generally more susceptible to biodegradation than anaerobically degradable compounds. In some cases, the formation of other compounds not originally present in the material can occur. Loss or gain of VOCs leads to analytical results that are unrepresentative of field conditions.  
5.2 Ancillary information concerning sample collection, handling, and storage for VOC analysis is provided in Appendix X1 – Appendix X3. These appendixes and cited references are recommended reading for those unfamiliar with the many challenges presented during the collection, handling, and storage of samples for VOC analysis.
SCOPE
1.1 This guide describes recommended procedures for the collection, handling, and preparation of solid waste, soil, and sediment samples for subsequent determination of volatile organic compounds (VOCs). This class of compounds includes low molecular weight aromatics, hydrocarbons, halogenated hydrocarbons, ketones, acetates, nitriles, acrylates, ethers, and sulfides with boiling points below 200° Celsius (C) that are insoluble or slightly soluble in water.  
1.2 Methods of sample collection, handling, storage, and preparation for analysis are described.  
1.3 This guide does not cover the details of sampling design, laboratory preparation of containers, and the analysis of the samples.  
1.4 It is recommended that this guide be used in conjunction with Guide D4687.  
1.5 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “standard” in the title of this document means only that the document has been approved through the ASTM consensus process.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. Reporting of test results in units other than SI shall not be regarded as nonconformance with this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    16 pages
    English language
    sale 15% off
  • Guide
    16 pages
    English language
    sale 15% off
ASTM
ASTM D8064-16(Test Method)
Standard Test Method for Elemental Analysis of Soil and Solid Waste by Monochromatic Energy Dispersive X-ray Fluorescence Spectrometry Using Multiple Monochromatic Excitation Beams

SIGNIFICANCE AND USE
5.1 Elemental species such as Cr, Ni, As, Cd, Hg, and Pb are widely used in many industrial processes. These elements have been identified in many former industrial sites driving the need for a quick, easy method for testing on-site at trace levels in soil and solid waste matrices.  
5.2 This method may be used for quantitative determinations of Cr, Ni, As, Cd, Hg, and Pb in soil matrices and solid waste. Typical test time is 90 seconds to 15 minutes.
SCOPE
1.1 This test method is based upon energy-dispersive X-ray Fluorescence (EDXRF) spectrometry using multiple monochromatic excitation beams for detection and quantification of selected heavy metal elements in soil and related solid waste.  
1.2 This test method is also known as High Definition X-ray Fluorescence (HDXRF) or Multiple Monochromatic Beam EDXRF (MMB-EDXRF).  
1.3 This test method is applicable to various soil matrices for the determination of Cr, Ni, As, Cd, Hg, and Pb in the range of 1 to 5000 mg/kg, as specified in Table 1 and determined by a ruggedness study using representative samples. The limit of detection (LOD) for each element is listed in Table 1. The LOD is estimated by measuring a SiO2 blank sample (see Table X1.1 in Appendix X1).  
1.4 This test method is applicable to other elements: Sb, Cu, Se, Ag, Tl, Zn, Ba, Au, Co, V, Fe, Mn, Mo, K, Rb, Sn, Sr, and Ti.  
1.5 X-ray Nomenclature—This standard names X-ray lines using the Siegbahn convention.2  
1.6 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    12 pages
    English language
    sale 15% off
ASTM
ASTM D4646-16(2023)(Test Method)
Standard Test Method for 24 h Batch-Type Measurement of Contaminant Sorption by Soils and Sediments

SIGNIFICANCE AND USE
5.1 This test method is meant to allow for a rapid (24 h) index of a geomedia's sorption affinity for given solutes in environmental waters or leachates. A large number of samples may be run in parallel using this test method to determine a comparative ranking of those samples, based upon the amount of solute sorbed by the geomedia, or by various geomedia or leachate constituents. The 24 h time is used to make the test convenient and also to minimize microbial, light, or hydrolytic degradation which may be a problem in longer timed procedures. While Kd values are directly applicable for screening and comparative ranking purposes, their use in predictive field applications generally requires the assumption that Kd be a fixed value.  
5.2 While this test method may be useful in determining 24 h Kd values for nonvolatile organic constituents, interlaboratory testing has been carried out only for the nonvolatile inorganic species arsenic and cadmium (see Section 12). However, the procedure has been tested for single-laboratory precision with polychlorinated biphenyls (PCBs) and is believed to be useful for all stable and nonvolatile inorganic and organic constituents. This test method is not considered appropriate for volatile constituents.  
5.3 The 24 h time limit may be sufficient to reach a steady-state Kd; however, the calculated Kd value should be considered a non-equilibrium measurement unless steady-state has been determined. To report this determination as a steady-state Kd, this test method should be conducted for intermediate times (for example, 12, 18, and 22 h) to ensure that the soluble concentrations in the solution have reached a steady state by 24 h. If a test duration of greater than 24 h is required, refer to Test Method D4319 for an alternate procedure of longer duration.
SCOPE
1.1 This test method describes a procedure for determining the sorption affinity of waste solutes by unconsolidated geologic material in aqueous suspension. The waste solute may be derived from a variety of sources such as wells, underdrain systems, or laboratory solutions such as those produced by waste extraction tests like the Practice D3987 shake extraction method.  
1.2 This test method is applicable in screening and providing relative rankings of a large number of geomedia samples for their sorption affinity in aqueous leachate/geomedia suspensions. This test method may not simulate sorption characteristics that would occur in unperturbed geologic settings.  
1.3 While this procedure may be applicable to both organic and inorganic constituents, care must be taken with respect to the stability of the particular constituents and their possible losses from solution by such processes as degradation by microbes, light, hydrolysis, or sorption to material surfaces. This test method should not be used for volatile chemical constituents (see 6.1).  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM E2993-23(Guide)
Standard Guide for Evaluating Potential Hazard in Buildings as a Result of Methane in the Vadose Zone

SIGNIFICANCE AND USE
5.1 Several different factors should be taken into consideration when evaluating methane hazard, rather than, for example, use of a single concentration-based screening level as a de-facto hazard assessment level. Key variables are identified and briefly discussed in this section. Legal background information is provided in Appendix X3. The Bibliography includes references where more detailed information can be found on the effect of various parameters on gas concentrations.  
5.2 Application—This guide is intended for use by those undertaking an assessment of hazards to people and property as a result of subsurface methane suspected to be present based on due diligence or other site evaluations (see 6.1.1).  
5.2.1 This guide addresses shallow methane, including its presence in the vadose zone; at residential, commercial, and industrial sites with existing construction; or where development is proposed.  
5.3 This guide provides a consistent, streamlined process for deciding on action and the urgency of action for the identified hazard. Advantages include:  
5.3.1 Decisions are based on reducing the actual risk of adverse impacts to people and property.  
5.3.2 Assessment is based on collecting only the information that is necessary to evaluate hazard.  
5.3.3 Available resources are focused on those sites and conditions that pose the greatest risk to people and property at any time.  
5.3.4 Response actions are chosen based on the existence of a hazard and are designed to mitigate the hazard and reduce risk to an acceptable level.  
5.3.5 The urgency of initial response to an identified hazard is commensurate with its potential adverse impact to people and property.  
5.4 Limitations—This guide does not address potential hazards from other gases and vapors that may also be present in the subsurface such as hydrogen sulfide, carbon dioxide, and/or volatile organic compounds (VOCs) that may co-occur with methane. If the presence of hydrogen sulfide or other...
SCOPE
1.1 This guide provides a consistent basis for assessing methane in the vadose zone, evaluating hazard and risk, determining the appropriate response, and identifying the urgency of the response.  
1.2 Purpose—This guide covers techniques for evaluating potential hazards associated with methane present in the vadose zone beneath or near existing or proposed buildings or other structures (for example, potential fires or explosions within the buildings or structures), when such hazards are suspected to be present based on due diligence or other site evaluations (see 6.1.1). Buildings in this context include normal below grade utilities associated with a building.  
1.3 Objectives—This guide: (1) provides a practical and reasonable industry standard for evaluating, prioritizing, and addressing potential methane hazards based on mass flow and (2) provides a tool for screening out low-risk sites.  
1.4 This guide offers a set of instructions for performing one or more specific operations. This guide cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This guide is not intended to represent or replace the standard of care by which the adequacy of a given professional service should be judged, nor should this guide be applied without consideration of a project's many unique aspects. The word “Standard” in the title means only that the guide has been approved through the ASTM International consensus process.  
1.5 Not addressed by this guide are:  
1.5.1 Requirements or guidance or both with respect to methane sampling or evaluation in federal, state, or local regulations. Users are cautioned that federal, state, and local guidance may impose specific requirements that differ from those of this guide;  
1.5.2 Safety concerns, if any, associated with its use. It is the responsibility of the user of this sta...

  • Guide
    34 pages
    English language
    sale 15% off
  • Guide
    34 pages
    English language
    sale 15% off
ASTM
ASTM E3361-22(Guide)
Standard Guide for Estimating Natural Attenuation Rates for Non-Aqueous Phase Liquids in the Subsurface

SIGNIFICANCE AND USE
4.1 Guidance on management of NAPL sites and a large body of research effort contributing to their development (for example, ITRC 2018 (1); CRC CARE 2018 (2); CL:AIRE 2019 (3) and CRC CARE 2020 (4)) point to the significance of natural attenuation and NSZD in the evolution of NAPL source and the resulting distributions of COCs in soil, groundwater and vapor.  
4.2 Examples of reported ranges in estimated natural attenuation rates are 300 – 7700 gallons of NAPL/acre/year (Garg et al. 2017 (5)); and 0.4 – 280 metric tons of NAPL/year (CRC CARE 2020 (4)).  
4.3 The intent of this guide is to provide a standardized approach for the estimation of natural attenuation rates for NAPL in the subsurface. The rates can be used for establishing a baseline metric for those involved in the remedial decision-making process. There is a need for a systematic approach and refinement in data collection and interpretation for quantifying the spatially and temporally variable rates. Providing quality assurance in estimation of this metric will enable the assessment of relatively more engineered remedies as compared to natural remedies or MNA (Fig. 1), as well as estimation of the remediation timeframe. This comparison, when performed through a standardized approach, can lead to actionable metrics for transition to sustainable remedies through well-defined and transparent criteria. In the context of a spectrum of remediation options in terms of engineered and natural remedies (Fig. 1), the transition is from a relatively more engineered (or active remediation) to a relatively more nature-based remedy. When considered in the remedial decision-making process, estimates of natural attenuation rates can be used:  
4.3.1 Before active remediation (as baseline to assess whether active remediation is needed);  
4.3.2 During active remediation (as performance/optimization metric); and  
4.3.3 At the end of active remediation (support transition to MNA or site closure).  
4.4 Since natural ...
SCOPE
1.1 This is a guide for determining the appropriate method or combination of methods for the estimation of natural attenuation or depletion rates at sites with non-aqueous phase liquid (NAPL) contamination in the subsurface. This guide builds on a number of existing guidance documents worldwide and incorporates the advances in methods for estimating the natural attenuation rates.  
1.2 The guide is focused on hydrocarbon chemicals of concern (COCs) that include petroleum hydrocarbons derived from crude oil (for example, motor fuels, jet oils, lubricants, petroleum solvents, and used oils) and other hydrocarbon NAPLs (for example, creosote and coal tars). While much of what is discussed may be relevant to other organic chemicals, the applicability of the standard to other NAPLs, like chlorinated solvents or polychlorinated biphenyls (PCBs), is not included in this guide.  
1.3 This guide is intended to evaluate the role of NAPL natural attenuation towards reaching the remedial objectives and/or performance goals at a specific site; and the selection of an appropriate remedy, including remediation through monitoring of natural or enhanced attenuation, or the remedy transition to natural mechanisms. While the evaluation can support some aspects of site characterization, the development of the conceptual site model and risk assessment, it is not intended to replace risk assessment and mitigation, such as addressing potential impact to human health or environment, or need for source control.  
1.4 Estimation of NAPL natural attenuation rates in the subsurface relies on indirect measurements of environmental indicators and their variation in time and space. Available methods described in this standard are based on evaluation of biogeochemical reactions and physical transport processes combined with data analysis to infer and quantify the natural attenuation rates for NAPL present in the vadose and/or saturated zones.  
1.5...

  • Guide
    47 pages
    English language
    sale 15% off
ASTM
ASTM D7521-22(Test Method)
Standard Test Method for Determination of Asbestos in Soil

SIGNIFICANCE AND USE
5.1 This analysis method is used for the testing of soil samples for asbestos. The emphasis is on detection and analysis of sieved particles for asbestos in the soil. Debris identifiable as bulk building material that is readily separable from the soil is to be analyzed and reported separately.  
5.2 The coarse fraction of the sample (>2 mm to  
5.3 This test method does not describe procedures or techniques required to evaluate the safety or habitability of buildings or outdoor areas potentially contaminated with asbestos-containing materials or compliance with federal, state, or local regulations or statutes. It is the investigator's responsibility to make these determinations.  
5.4 Whereas this test method produces results that may be used for evaluation of sites contaminated by construction, mine, and manufacturing wastes; deposits of natural occurrences of asbestos; and other sources of interest to the investigator, the application of the results to such evaluations and the conclusions drawn there from, including any assessment of risk or liability, is beyond the scope of this test method and is the responsibility of the investigator.
SCOPE
1.1 This test method covers a procedure to: (1) identify asbestos in soil, (2) provide an estimate of the concentration of asbestos in the sampled soil (dried), and (3) optionally to provide a concentration of asbestos reported as the number of asbestos structures per gram of sample.  
1.2 In this test method, results are produced that may be used for evaluation of sites contaminated by construction, mine and manufacturing wastes, deposits of natural occurrences of asbestos (NOA), and other sources of interest to the investigator.  
1.3 This test method describes the gravimetric, sieve, and other laboratory procedures for preparing the soil for analysis as well as the identification and quantification of any asbestos detected. Pieces of collected soil and material embedded therein that pass through a 19-mm sieve will become part of the sample that is analyzed and for which results are reported.  
1.3.1 Asbestos is identified and quantified by polarized light microscopy (PLM) techniques including analysis of morphology and optical properties. Optional transmission electron microscopy (TEM) identification and quantification of asbestos is based on morphology, selected area electron diffraction (SAED), and energy dispersive X-ray analysis (EDXA). Some information about fiber size may also be determined. The PLM and TEM methods use different definitions and size criteria for fibers and structures. Separate data sets may be produced.  
1.4 This test method has an analytical sensitivity of 0.25 % by weight with optional procedures to allow for an analytical sensitivity of 0.1 % by weight.  
1.5 This test method does not purport to address sampling strategies or variables associated with soil environments. Such considerations are the responsibility of the investigator collecting and submitting the sample. Appendix X2 covering elements of soil sampling and good field practices is attached.  
1.6 Units—The values stated in SI units are to be regarded as the standard. Other units may be cited in the method for informational purposes only.  
1.7 Hazards—Asbestos fibers are acknowledged carcinogens. Breathing asbestos fibers can result in disease of the lungs including asbestosis, lung cancer, and mesothelioma. Precautions should be taken to avoid creating and breathing airborne asbestos particles when sampling and analyzing materials suspected of containing asbestos.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.9 This international standard was developed in accordance with internationally ...

  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    14 pages
    English language
    sale 15% off
ASTM
ASTM D7014-22(Practice)
Standard Practice for Installation of Double-Twisted Wire Mesh Gabions and Revet Mattresses

SIGNIFICANCE AND USE
4.1 Gabions and Revet Mattresses, as described in Specification A975, are used to achieve soil stability and prevent soil erosion and are also used as retaining wall structures to resist movements due to gravity. Their ability to function properly depends on correct design and installation. This standard practice describes the proper installation of gabions and revet mattresses to ensure the products function as intended by the manufacturers.
SCOPE
1.1 This specification covers standard practice for foundation preparation, assembly, placement and filling of double-twisted wire mesh gabions and revet mattresses used for various erosion control, soil retention or freestanding structures.  
1.2 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process."  
1.3 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are provided for information only and are not considered standard.  
1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off