ASTM D6644-01(2021)

ASTM D6644-01(2021) is a standard published by ASTM International. Its full title is "Standard Test Method for Tension Strength of Sew-Through Flange Buttons". This standard covers: SIGNIFICANCE AND USE 5.1 This test measures an important property to users of sew through flange buttons. This is a means of determining the resistance of the bridge of the button to a strain which can cause it to fall off a garment to which it is attached. 5.2 If there are differences of practical significance between the reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing, Other materials with established test values may be used for this purpose. The test results for the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias. SCOPE 1.1 This test method measures the resistance of the bridge of a sew-through button to a steadily increasing strain. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE 5.1 This test measures an important property to users of sew through flange buttons. This is a means of determining the resistance of the bridge of the button to a strain which can cause it to fall off a garment to which it is attached. 5.2 If there are differences of practical significance between the reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing, Other materials with established test values may be used for this purpose. The test results for the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias. SCOPE 1.1 This test method measures the resistance of the bridge of a sew-through button to a steadily increasing strain. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D6644-01(2021) is classified under the following ICS (International Classification for Standards) categories: 19.060 - Mechanical testing; 59.020 - Processes of the textile industry. The ICS classification helps identify the subject area and facilitates finding related standards.

ASTM D6644-01(2021) has the following relationships with other standards: It is inter standard links to ASTM D618-08, ASTM D618-05, ASTM D618-00, ASTM D5497-94c(2000). Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

ASTM D6644-01(2021) is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.