ISO/TC 115/SC 3 - Installation and special application

ISO 18647:2017 gives requirements for the design, fabrication, installation, commissioning and integrity management of modular drilling rigs on offshore fixed platforms. The modular drilling rig includes some or all of the equipment as follows: - drilling equipment including a derrick/mast and its controls that can be moved by skidding a drilling support structure; - drilling support equipment which includes support facilities such as power supply/distribution system; - mud and cement storage, mixing, monitoring and control equipment. ISO 18647:2017 is applicable to the modular drilling equipment on offshore structures for the petroleum and natural gas industries, as follows: - new equipment arranged in a modularized form; - the equipment contained in several modules, each of which can be lifted and installed on to the platform, however, the equipment may be arranged within the modules as is convenient; - the modules assembled together offshore for hook up and commissioning; - intended for long term use on a new fixed offshore structure; - Intended for temporary use on a number of different offshore platforms. ISO 18647:2017 is not applicable to drilling equipment - installed on mobile offshore units, and - intended primarily for onshore use. ISO 18647:2017 does not apply to those parts and functions of an offshore platform that are not directly related to drilling.

ISO 17349:2016 contains provisions for design of topside facilities for offshore plants handling CO2-rich streams at high pressures; i.e. CO2 molar concentration above 10 %. The surface systems include usual offshore process unit operations, as shown in Figure 1. ISO 17349:2016 is applicable only to topside facilities of fixed and floating oil and gas production offshore units up to the last barrier, such as an ESDV. Subsea production systems and Cryogenic CO2 separation are not covered.

ISO 17348:2016 provides guidelines and requirements for material selection of both seamless casing and tubing, and downhole equipment for CO2 gas injection and gas production wells with high pressure and high CO2 content environments [higher than 10 % (molar) of CO2 and 1 MPa CO2 partial pressure]. Oil production wells are not covered in this International Standard. This International Standard only considers materials compatibility with the environment. Guidance is given for the following: - corrosion evaluation; - materials selection; - corrosion control. ISO 17348:2016 is aimed at high CO2 content wells, where the threat of low pH and CO2 corrosion is greatest. However, many aspects are equally applicable to environments containing lower CO2 concentrations. Materials selection is influenced by many factors and synergies and should be performed by either materials or corrosion engineer.

ISO 17945:2015 establishes material requirements for resistance to SSC in sour petroleum refining and related processing environments containing H2S either as a gas or dissolved in an aqueous (liquid water) phase with or without the presence of hydrocarbon. This International Standard does not include and is not intended to include design specifications. Other forms of wet H2S cracking, environmental cracking, corrosion, and other modes of failure are outside the scope of this International Standard. It is intended to be used by refiners, equipment manufacturers, engineering contractors, and construction contractors. Specifically, this International Standard is directed at the prevention of SSC of equipment (including pressure vessels, heat exchangers, piping, valve bodies, and pump and compressor cases) and components used in the refining industry. Prevention of SSC in carbon steel categorized under P-No. 1 in Section IX of the ASME Boiler and Pressure Vessel Code (BPVC) is addressed by requiring compliance with NACE SP0472. ISO 17945:2015 applies to all components of equipment exposed to sour refinery environments (see Clause 6) where failure by SSC would (1) compromise the integrity of the pressure-containment system, (2) prevent the basic function of the equipment, and/or (3) prevent the equipment from being restored to an operating condition while continuing to contain pressure.

ISO 13709:2009 specifies requirements for centrifugal pumps, including pumps running in reverse as hydraulic power recovery turbines, for use in petroleum, petrochemical and gas industry process services. ISO 13709:2009 is applicable to overhung pumps, between-bearings pumps and vertically-suspended pumps

ISO/TR 17766:2005 gives performance corrections for all worldwide designs of centrifugal pumps of conventional design, in the normal operating range, with open or closed impellers, single or double suction, pumping Newtonian fluids.

ISO 13710:2004 specifies requirements for reciprocating positive-displacement pumps and pump units for use in the petroleum, petrochemical and natural gas industries. It is applicable to both direct-acting and power-frame types. ISO 13710:2004 is not applicable to controlled-volume pumps and rotary pumps.

ISO 21049:2004 specifies requirements and gives recommendations for sealing systems for centrifugal and rotary pumps used in the petroleum, natural gas and chemical industries. It is applicable mainly for hazardous, flammable and/or toxic services where a greater degree of reliability is required for the improvement of equipment availability and the reduction of both emissions to the atmosphere and life-cycle sealing costs. It covers seals for pump shaft diameters from 20 mm (0,75 in) to 110 mm (4,3 in). ISO 21049:2004 is also applicable to seal spare parts and can be referred to for the upgrading of existing equipment. A classification system for the seal configurations covered by ISO 21049:2004 into categories, types, arrangements and orientations is provided.

ISO 13709:2003 specifies requirements for centrifugal pumps, including pumps running in reverse as hydraulic power recovery turbines, for use in petroleum, petrochemical and gas industry process services. ISO 13709:2003 is applicable to overhung pumps, between-bearings pumps and vertically-suspended pumps. Clause 8 provides requirements applicable to specific types of pump. All other clauses of ISO 13709:2003 are applicable to all pump types. Illustrations are provided of the various specific pump types and the designations assigned to each specific type. ISO 13709:2003 is not applicable to sealless pumps.