CEN/TC 132/WG 5 - Extruded and drawn products

This document specifies the chemical composition limits of wrought aluminium and wrought aluminium alloys and form of products.
NOTE The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminium Association, 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209, USA, for the corresponding alloys.

This document specifies the chemical composition limits of wrought aluminium and wrought aluminium alloys and form of products.
NOTE The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminium Association, 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209, USA, for the corresponding alloys.

This European Standard specifies the mechanical property limits resulting from tensile testing applicable to aluminium and aluminium alloy extruded rod/bar, tube and profile.
Technical conditions for inspection and delivery, including product and testing requirements, are specified in EN 755 1. Temper designations are defined in EN 515. The chemical composition limits for these materials are given in EN 573 3.

This document specifies the chemical composition limits of wrought aluminium and wrought aluminium alloys and form of products.
NOTE The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminium Association, 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209, USA, for the corresponding alloys.

This document specifies the chemical composition limits of wrought aluminium and wrought aluminium alloys and form of products.
NOTE The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminium Association, 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209, USA, for the corresponding alloys.

TC request to delete an unnecessary and confusing Figure in publication

This European Standard specifies tolerances on dimensions and form of extruded precision profiles, in alloys EN AW-6060 and EN AW-6063 manufactured with and without a thermal barrier (see Figures 1 and 2). It applies to extruded products supplied without further surface treatment. Precision profiles covered in this standard are distinguished from extruded profiles for general applications covered in EN 755-9 by the following characteristics:
-   they are mainly for architectural applications;
-   they meet more stringent requirements regarding the surface condition of visible surfaces;
-   the maximum diameter of the circumscribing circle CD is 350 mm;
-   they are made to closer tolerances on dimensions and form.
In the case of profiles which, due to the complexity of their design, are difficult to manufacture and specify, then special agreements between supplier and purchaser may need to be reached.
NOTE   The effect of the thermal barrier material on the dimensional tolerances is covered by this document although the actual thermal barrier material itself is not (see EN 14024).

This European Standard specifies the mechanical property limits resulting from tensile testing applicable to aluminium and aluminium alloy cold drawn rod/bar and tube. Technical conditions for inspection and delivery, including product and testing requirements, are specified in EN 754-1. Temper designations are defined in EN 515. The chemical composition limits for these materials are given in EN 573-3.

This European Standard specifies the chemical composition limits of wrought aluminium and wrought aluminium alloys and form of products.
The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminum Association, 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209, USA, for the corresponding alloys.
Guidelines for the introduction of new wrought aluminium and wrought aluminium alloys in standards are presented in Annex B.

This European Standard specifies the mechanical properties of wrought aluminium and wrought aluminium alloy sheet, strip and plate for general engineering applications.
It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock) or to special products such as corrugated, embossed, painted, sheets and strips or to special applications such as aerospace, can stock, finstock, for which mechanical properties are specified in separate European Standards.
The chemical composition limits of the alloys are specified in EN 573-3.
Temper designations are defined in Annex B, in compliance with the provisions of EN 515.

This document specifies the tolerances on dimensions and form for aluminium and aluminium alloy cold drawn porthole tubes with an outside diameter (OD) from 3 mm to 350 mm (round tube, see Figure 1) or with a cross section contained within a circumscribing circle (CD) from 8 mm to 300 mm (other than round tube, see Figure 2), supplied in straight lengths.
This document only applies to cold drawn tube for general engineering applications made in the following alloys:
-   EN AW-1050A, EN AW-1200;
-   EN AW-3003, EN AW-3103;
-   EN AW-5005, EN AW-5005A, EN AW-5049, EN AW-5251, EN AW-5052;
-   EN AW-6012, EN AW-6060, EN AW-6061, EN AW-6262, EN AW-6262A;
-   EN AW-6063, EN AW-6063A, EN AW-6065, EN AW-6082;
-   EN AW-7020.
The temper designations used in this part are according to EN 515.
This document only applies to tube produced by the porthole/bridge method of extrusion only (and then cold drawn to the final dimensions).
This document does not apply to:
-   cold drawn tubes produced by the seamless, die/mandrel method (EN 754-7),
-   tubes delivered in coils (EN 13958),
-   coiled tubes cut to length (EN 13958).

This document specifies technical conditions for inspection and delivery of alloys EN AW-6060 and EN AW-6063 extruded precision profiles manufactured with and without a thermal barrier (see Figures 1 and 2) and without further surface treatment.
Precision profiles covered in this document are distinguished from extruded profiles for general applications covered in EN 755-9 by the following characteristics:
   they are mainly for architectural applications;
   they meet more stringent requirements regarding the surface condition of visible surfaces;
    the maximum diameter of the circumscribing circle CD is 350 mm;
   they are made to closer tolerances on dimensions and form.
In the case of profiles, which, due to the complexity of their design are difficult to manufacture and specify, then special agreements between supplier and purchaser may need to be reached.
NOTE   The effect of the thermal barrier material on the dimensional tolerances is covered by EN 12020-2 although the actual thermal barrier material itself is not (see EN 14024).

This document specifies the technical conditions for inspection and delivery of wrought aluminium and aluminium alloy extruded rod/bar, tube and profile for general engineering applications.
This document does not apply to:
-   forging stock (EN 603),
-   extruded precision profiles in alloys EN AW-6060 and EN AW-6063 (EN 12020),
-   products delivered in coils (prEN 13957),
-   coiled tubes cut to length (prEN 13957).

This document specifies the tolerances on dimensions and form for aluminium and aluminium alloy extruded profile with a cross section contained within a circumscribing circle not greater than 800 mm (see Figure 1).
The temper designations used in this part are according to EN 515.
This standard applies to extruded profiles for general engineering applications only.

This document specifies the tolerances on dimensions and form for aluminium and aluminium alloy extruded porthole tubes with an outside diameter (OD) from 8 mm to 450 mm (round tube, see Figure 1) or with a cross section contained within a circumscribing circle (CD) from 10 mm to 350 mm (other than round tube, see Figure 2), supplied in straight lengths.
This standard only applies to extruded porthole tube for general engineering applications made in the following alloys:
-   EN AW-1050A, EN AW-1200, EN AW-1350;
-   EN AW-3003, EN AW-3103;
-   EN AW-5005, EN AW-5005A, EN AW-5049, EN AW-5051A, EN AW-5251, EN AW-5052;
-   EN AW-6101A, EN AW-6101B, EN AW-6005, EN AW-6005A, EN AW-6008, EN AW-6110A, EN AW-6012, EN AW-6014, EN AW-6018, EN AW-6351, EN AW-6060, EN AW-6360, EN AW-6061, EN AW-6261,
EN AW-6262, EN AW-6262A, EN AW-6063, EN AW-6063A, EN AW-6463, EN AW-6065, EN AW-6081,
EN AW-6082; EN AW-6182,
-   EN AW-7003, EN AW-7005, EN AW-7108, EN AW-7108A, EN AW-7020.
The temper designations used in this part are according to EN 515.
This standard only applies to tube produced by the tube porthole/bridge method.
This standard does not apply to:
-   extruded tubes produced by the seamless, die/mandrel method (EN 755-7),
-   tubes delivered in coils (prEN 13957),
-   coiled tubes cut to length (prEN 13957).

This document specifies tolerances on dimensions and form of extruded precision profiles, in alloys EN AW-6060 and EN AW-6063 manufactured with and without a thermal barrier (see Figures 1 and 2). It applies to extruded products supplied without further surface treatment. Precision profiles covered in this standard are distinguished from extruded profiles for general applications covered in EN 755-9 by the following characteristics:
   they are mainly for architectural applications;
   they meet more stringent requirements regarding the surface condition of visible surfaces;
   the maximum diameter of the circumscribing circle CD is 350 mm;
   they are made to closer tolerances on dimensions and form.
In the case of profiles which, due to the complexity of their design, are difficult to manufacture and specify, then special agreements between supplier and purchaser may need to be reached.
NOTE   The effect of the thermal barrier material on the dimensional tolerances is covered by this document although the actual thermal barrier material itself is not (see EN 14024).

This document specifies the tolerances on dimensions and form for aluminium and aluminium alloy extruded seamless tubes with an outside diameter (OD) from 8 mm to 450 mm (round tube, see Figure 1) or with a cross section contained within a circumscribing circle (CD) from 10 mm to 350 mm (other than round tube, see Figure 2), supplied in straight lengths.
This standard only applies to tube produced by the seamless die/mandrel method of extrusion. This standard applies to extruded seamless tube for general engineering applications only.
The temper designations used in this part are according to EN 515.
This European Standard does not apply to:
-   extruded tubes produced by porthole/bridge method (EN 755-8),
-   tubes delivered in coils (prEN 13957),
-   coiled tubes cut to length (prEN 13957).

This document specifies the tolerances on dimensions and form for aluminium and aluminium alloys cold drawn seamless tubes with an outside diameter (OD) from 3 mm to 350 mm (round tube, see Figure 1) or with a cross section contained within a circumscribing circle (CD) from 8 mm to 300 mm (other than round tube, see Figure 2) supplied in straight lengths.
This standard only applies to tube produced by the seamless die/mandrel method of extrusion (and then cold drawn to the final dimensions required).
The temper designations used in this part are according to EN 515.
This document applies to cold drawn, seamless tube for general engineering applications.
This document does not apply to:
-   cold drawn tube produced by the porthole/bridge method (EN 754-8),
-   tubes delivered in coils (EN 13958),
-   coiled tubes cut to length (EN 13958).

This document specifies the technical conditions for inspection and delivery of aluminium and aluminium alloy cold drawn rod/bar and tube for general engineering applications.
This document applies to products which are extruded and then cold drawn.
This document does not apply to:
-   forging stock (EN 603),
-   products delivered in coils (EN 13958),
-   coiled tubes cut to length (EN 13958).

This document specifies the mechanical property limits resulting from tensile testing applicable to aluminium and aluminium alloy cold drawn rod/bar and tube.
Technical conditions for inspection and delivery, including product and testing requirements, are specified in EN 754-1. Temper designations are defined in EN 515. The chemical composition limits for these materials are given in EN 573-3.

This document specifies the mechanical property limits resulting from tensile testing applicable to aluminium and aluminium alloy extruded rod/bar, tube and profile.
Technical conditions for inspection and delivery, including product and testing requirements, are specified in EN 755-1. Temper designations are defined in EN 515. The chemical composition limits for these materials are given in EN 573-3.

This European Standard specifies the technical conditions for inspection and delivery, mechanical properties and tolerances on dimensions and form for aluminium alloy cold drawn round, coiled tubes for general applications with outside or inside diameters in the range from 2 mm up to and including 25 mm.
Depending on the final application of the product, additional or stricter requirements can apply, after agreement between supplier and purchaser.
NOTE   Some of the products listed in the present standard can be subject to patent or patent applications, and their listing herein is not be construed in any way as the granting of a licence under such patent right.
CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licences on standardised standard products under reasonable and not discriminatory conditions then this product shall be removed from the corresponding standard.

This standard specifies the technical conditions for inspection and delivery, mechanical properties and tolerances on dimensions and form for aluminium and aluminium alloy extruded round, coiled tubes for general applications with outside or inside diameters in the range from 5 mm up to and including 30 mm.
Depending on the final application of the product, additional or stricter requirements can apply, after agreement between supplier and purchaser.
NOTE   Some of the products listed in the present standard can be subject to patent or patent applications, and their listing herein is not be construed in any way as the granting of a licence under such patent right.
CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licences on standardised standard products under reasonable and not discriminatory conditions then this product shall be removed from the corresponding standard.

This part prEN 12020 specifies the tolerances on dimensions and form of extruded precision profiles, in alloys EN AW-6060 and EN AW-6063 manufactured with and without a thermal barrier (see figures 1 and 2). This applies to as extruded products supplied without further surface treatment.

This part of EN 12020 (00132080) specifies the technical conditions for inspection and delivery of alloys EN AW-6060 and EN AW-6063 extruded, precision profiles manufactured with and without a thermal barrier (figures 1 and 2 respectively). This applies to as extruded products supplied without further surface treatment.

This part of EN 755 specifies the tolerances on dimensions and form for aluminium and aluminium alloy extruded profile with a cross section contained within a circumscribing circle not greater than 800 mm. This standard applies to extruded profile for general engineering applications only. The tolerances in this standard only apply to those dimensions that can be physically measured.

This part of EN 754 specifies the tolerances on dimensions and form for aluminium and aluminium alloy cold drawn porthole tubes with an outside diameter (OD) from 3 mm to 350 mm (round tube, see figure 1) or with a cross section contained within a circumscribing circle (CD) from 8 mm to 300 mm (other thane round tube, see figure 2), supplied in straight lengths. This standard only applies to tube produced by the porthole/bridge method of extrusion only (and then cold drawn to the final dimensions required).

This part of EN 755 specifies the tolerances on dimensions and form for aluminium and aluminium alloy extruded seamless tubes with an outside diameter (OD) from 8 mm to 350 mm (round tube, see figure 1) or with a cross section contained within a circumscribing circle (CD) from 10 mm to 450 mm (other than round tube, see figure 2), supplied in straight lengths. This standard only applies to tube produced by the seamless die/mandrel method of extrusion. This standard applies to extruded seamless tube for general engineering applications only.

This part of EN 755 specifies the tolerances on dimensions and form for aluminium and aluminium alloy extruded porthole tubes with an outside diameter (OD) from 8 mm to 350 mm (round tube, see figure 1) or with a cross section contained within a circumscribing circle (CD) from 10 mm to 450 mm (other than round tube, see figure 2) supplied in straight lengths. This standard only applies to extruded porthole tube for general engineering applications made in the following alloys: EN AW-1050A, EN AW-1200, EN AW-1350, EN AW-3003, EN AW-3103, EN AW-5005, EN AW-5005A, EN AW-5051A, EN AW-5251, EN AW-5052, EN AW-6101A...

This part of EN 754 specifies the tolerances on dimensions and form for aluminium and aluminium alloy cold drawn seamless tubes with an outside diameter (OD) from 3 mm to 350 mm (round tube, see figure 1) or with a cross section contained within a circumscribing circle (CD) from 8 mm to 300 mm (other than round tube, see figure 2) supplied in straight lengths. This standard only applies to tube produced by the seamless die/mandrel method of extrusion (and then cold drawn to the final dimensions required).

This part of EN 755 specifies the technical conditions for inspection and delivery of wrought aluminium and aluminium alloy extruded rod/bar, tube and profile for general engineering applications.  This specification excludes forging stock, EN AW-6060 / EN AW-6063 extruded precision profiles, and products delivered in coils.

This part of EN 754 standard specifies the technical conditions for inspection and delivery of aluminium and aluminium alloy cold drawn rod/bar and tube for general engineering applications.  It applies to products which are extruded and then cold drawn. It does not, however, apply to products delivered in coils, or to products which are rolled and then cold drawn, e.g. seam-welded tube.

This part of EN 755 specifies the mechanical property limits applicable to aluminium and aluminium alloy extruded rod/bar, tube and profile.  Temper designations are defined in EN 515. The numerical designation system of alloys is specified in EN 573-1. The chemical symbol based designation system is specified in EN 573-2. The chemical composition limits for these materials are given in EN 573-3. Mechanical property limits are specified for all Class "A" alloys as defined in EN 573-4.

This part of EN 754 specifies the mechanical property limits applicable to aluminium and aluminium alloy cold drawn rod/bar and tube.  Temper designations are defined in EN 515. The numerical designation system of alloys is specified in EN 573-1. The chemical symbol based designation system is specified in EN 573-2. The chemical composition limits for these materials are specified in EN 573-3. Mechanical property limits are specified for all Class "A" alloys as defined in EN 573-4.

This part of EN 754 specifies the tolerances on dimensions and form for aluminium and aluminium alloy cold drawn round bars having diameters in the range from 3 mm up to and including 100 mm.

This part of EN 754 specifies the tolerances on dimensions and form for aluminium and aluminium alloy cold drawn square bars having widths across flats from 3 mm up to 100 mm.

This part of EN 754 specifies the tolerances on dimensions and form for aluminium and aluminium alloy cold drawn rectangular bars having thicknesses in the range from 2 mm up to 60 mm and widths in the range from 5 mm up to and including 200 mm.

This part of EN 754 specifies the tolerances on dimensions and form for aluminium and aluminium alloy cold drawn hexagonal bars having widths across flats in the range from 3 mm up to 80 mm.

This part of EN 755 specifies the tolerances on dimensions and form for aluminium and aluminium alloy extruded rectangular bars having thicknesses in the range from 2 mm up to 240 mm and widths in the range from 10 mm up to 600 mm.

This part of EN 755 specifies the tolerances on dimensions and form for aluminium and aluminium alloy extruded square bars having widths across flats from 10 mm up to 220 mm.

This part of EN 755 specifies the dimension and form tolerances for aluminium and aluminium alloy extruded hexagonal bars having widths across flats in the range from 10 mm up to 220 mm.

This part of EN 755 specifies the tolerances on dimensions and form for aluminium and aluminium alloy extruded round bars having diameters in the range from 8 up to 320 mm.