ASD-STAN/D 3/S 2 - Fasteners

This document specifies the characteristics for screws, 100° countersunk reduced head, offset cruciform recess, close tolerance shank, short thread, in titanium alloy, anodized, MoS2 lubricated, classification 1 100 MPa/315 °C, inch series, for aerospace applications.

This document specifies the characteristics of self-locking shank nuts in NI-P101HT, silver plated, for use in 30° cone holes, for aerospace applications.
Classification: 1 210 MPa /730 °C .

This document specifies the characteristics of screws with 100° countersunk head, offset cruciform recess, threaded to head, in FE-PA92HT, for aerospace applications.
Classification: 900 MPa /650 °C .

This document specifies the characteristics, qualification and acceptance requirements for helical coil screw thread inserts.
It is applicable whenever referenced.

This document specifies the required characteristics, inspections, tests, quality assurance requirements, conditions for qualification acceptance and delivery of rotary fasteners for structural and non-structural applications.
This document applies to all rotary fasteners for structural and non-structural applications. It can be applied when referred to in the product standard or in a design specification.

This document specifies the characteristics for hexagon nuts, with counterbore and captive washer, with a self-locking feature achieved by forming the upper portion out-of-round, in steel, cadmium plated, MoS2 lubricated, classification 1 100 MPa /235 °C .

This document specifies the characteristics of hexagonal plain nuts, reduced height, normal across flats, in aluminium alloy, anodized, for aerospace applications.
Classification: 450 MPa /120 °C .

This document specifies the dimensions, tolerances, required characteristics and mass of a receptacle for use in fuselage interior equipment and structural applications. This document is intended to be used in conjunction with studs according to EN 6088  or EN 6105.

This document specifies the minimum requirements for the qualification, acceptance, delivery and
inspection of standard parts by the aerospace industry and its manufacturers.
This document is valid for standard parts and their assemblies as described in a product standard, if
mentioned therein. This specification can also be applied to other parts when specifically invoked by
the terms of delivery.
Parts/sections of this document are not applicable in cases where the product standard stipulates
requirements that differ from this specification.

This document specifies the dimensions of self-locking, silver-coated bi-hexagonal nuts with MJ-thread in heat resisting nickel base alloy NI-P101HT for aerospace applications.
Maximum test temperature of the material 730 °C.

This document specifies the characteristics of self-locking, floating, two lug anchor nuts, reduced series,
with counterbore, in steel, cadmium plated, MoS 2 lubricated.
Classification: 1 100 MPa1/235 °C2

This document specifies the characteristics of screws, pan head, offset cruciform recess, coarse tolerance
normal shank, short thread, in alloy steel, cadmium plated.
Classification: 900 MPa1/235 °C2.

This document specifies the characteristics of screws, pan head, offset cruciform recess, close tolerance
normal shank, short thread, in alloy steel, cadmium plated.
Classification: 900 MPa1/ 235 °C2.

This document specifies the dimensions, tolerances and masses of rivets with 100° normal flush head, close tolerance, inch series, for aerospace applications.

This document specifies the dimensions, tolerances and mass of rivets with 100° reduced flush head, close tolerance, inch series, for aerospace applications.

This document specifies the dimensions, tolerances and mass of rivets with universal head, close tolerance, inch series, for aerospace application.

This standard specifies characteristics of self-locking hexagonal slotted/castellated nuts, in steel, cadmium plated, MoS2 lubricated, for aerospace applications.
Classification: 900 MPa /235 °C .

This document specifies the dimensions, tolerances and mass of rivets with 100° medium flush head, close tolerance, inch series, for aerospace application.

This document defines the requirements for qualification, acceptance, delivery and inspection of 100° countersunk head, 100° countersunk reduced head and protruding head close tolerance pins, shear type in aluminium alloy 7050-T73 and collars of aluminium alloy 3003 and of aluminium alloy 6061-T7 for use as permanent fasteners in aerospace applications.

This document specifies the characteristics of plain hexagonal nuts, reduced height, normal across flats, in steel, cadmium plated, for aerospace applications.
Classification: 900 MPa/235 °C.

This document specifies the characteristics of externally threaded fasteners, 100° countersunk normal
head, Spiral Drive Recess, threaded to head, in heat and corrosion resisting steel, passivated, for
aerospace applications.

This document specifies the characteristics of externally threaded fasteners, 100° countersunk normal head, Spiral Drive Recess, coarse tolerance normal shank, medium length thread, in alloy steel, cadmium plated, for aerospace applications.
Classification: 1 100 MPa /235 °C .

This document specifies the characteristics of externally threaded fasteners, pan head, Spiral Drive
Recess, coarse tolerance normal shank, medium length thread, in alloy steel, cadmium plated, for
aerospace applications.
Classification: 1 100 MPa1/235 °C2.

This document specifies the characteristics of externally threaded fasteners, pan head, Spiral Drive
Recess, threaded to head, in heat and corrosion resisting steel, passivated, for aerospace applications.
Classification: 1 100 MPa1/425 °C2.

This document specifies the characteristics of externally threaded fasteners, 100° countersunk normal head, Spiral Drive Recess, close tolerance normal shank, short thread, in titanium alloy, aluminium IVD coated, for aerospace applications.
Classification: 1 100 MPa /425 °C

This document specifies the characteristics of externally threaded fasteners, pan head, Spiral Drive Recess, coarse tolerance normal shank, medium length thread, in titanium alloy, anodized, MoS2 lubricated, for aerospace applications.
Classification: 1 100 MPa /315 °C .

This document specifies the characteristics of externally threaded fasteners, 100° countersunk normal
head, Spiral Drive Recess, short thread, in heat resisting steel FE-PA2601, passivated, for aerospace
applications.
Classification: 900 MPa
1/650 °C2.

This document specifies the characteristics of externally threaded fasteners, 100° countersunk normal head, Spiral Drive Recess, for aerospace applications.
Classification: 1 100 MPa /425 °C .

This document specifies the characteristics of externally threaded fasteners, 100° countersunk normal head, Spiral Drive Recess, coarse tolerance normal shank, long thread, in alloy steel, cadmium plated, for aerospace applications.
Classification: 1 100 MPa /235 °C .

This document specifies the characteristics of screws, pan head, offset cruciform recess, coarse tolerance normal shank, short thread, in titanium alloy, anodized, MoS2 lubricated.
Classification: 1 100 MPa /315 °C ·

This document specifies the characteristics of self-locking, shank nuts, in NI-PH2601, silver plated, for aerospace applications.
Classification: 1 550 MPa /600 °C .

This document is the configuration master for the content and structure of externally threaded fastener product standards.
This document
- defines the content of externally threaded fastener product standards;
- is referenced in product standards;
- defines part numbering and title.
This configuration master defines externally threaded fasteners, metric and inch series.

This European Standard specifies dimensions, tolerances, characteristics and qualification requirements for MORTORQ Spiral Drive Recesses .
[MORTORQ® is the trade name of a product supplied by licensees of the Phillips Screw Company. This information is given for the convenience of users of this European Standard and does not constitute an endorsement by ASD-STAN nor CEN of the product named. Equivalent products may be used if they can be shown to lead to the same results.]

This European standard specifies the characteristics and technical requirements for protruding head tubular sleeves, in corrosion resisting steel, which may be plain or provided with a series of annular grooves.
Passivated sleeves are for use in aerospace assemblies whose maximum operating temperature does not exceed 650 °C. The operating temperatures for aluminium pigmented sleeves should not exceed 230 °C.

This European standard specifies the characteristics of bolts, shouldered, thin hexagonal head, close tolerance shank, short thread, in titanium alloy, anodized, MoS2 dryfilm coated, for aerospace applications.
Classification: 1 100 MPa /315 °C .
These bolts are intended to be used with washers according to EN 2414 and nuts according to EN 3230.

This European standard specifies the characteristics of screws, pan head, offset cruciform recess, coarse tolerance normal shank, long thread, in alloy steel, cadmium plated, for aerospace applications.
Classification: 1 100 MPa /235 °C .

This document specifies the technical, qualification and quality assurance requirements for bolts in material FE-PA2601 (A286) of tensile strength class 1 100 MPa at room temperature, maximum test temperature of material 650 °C.
Primarily for aerospace applications it is applicable to such bolts when referenced on the product standard or definition document.

This document specifies the characteristics, qualification and acceptance requirements for self locking shaft-nuts and threaded rings, with right- or left-hand MJ threads, in FE-PA2601, silver plated, for aerospace applications.
Temperature class: 450 °C ).
It is applicable whenever referenced.

This European standard specifies the characteristics, qualification and acceptance requirements for
bolts with MJ threads in TI-P64001, for aerospace applications.
Strength class: 1 100 MPa1.
It is applicable whenever referenced.

This document specifies the characteristics of chamfered washers, with counterbore, in alloy steel, cadmium plated, for maximum operating temperature 235 °C.

This standard specifies the characteristics, qualification and acceptance requirements for bolts with MJ threads in NI-PH2601.
Classification: 1 275 MPa /650 °C .
It is applicable whenever referenced.

This European standard specifies the characteristics of self-locking, fuel resistant, sealing, floating, two lug anchor nuts, with counterbore, in alloy steel, cadmium plated, MoS2 lubricated.
Classification: 900 MPa/120 °C.

This document specifies the characteristics of hexagon plain nuts, reduced height, reduced across flats, with left hand thread, in heat resisting steel, silver plated.
Classification: 600 MPa /425 °C.

This document specifies the characteristics of hexagon plain nuts, reduced height, reduced across flats, in heat resisting steel, silver plated.
Classification: 600 MPa/425 °C.

This document specifies the characteristics of hexagonal slotted/castellated nuts, normal height, normal across flats, in heat resisting steel, silver plated.
Classification: 1 100 MPa/650 °C.

This document specifies the technical, qualification and quality assurance requirements for sensor based clamp load measurement systems for high tensile bolts and other clamp load sensitive elements. Primarily for aerospace applications, it is applicable to such products when referenced on the product standard or drawing.

This European Standard specifies the required characteristics, inspections, tests, quality assurance requirements, conditions for qualification acceptance and delivery of quick release fastening systems.
This European Standard applies to all fastening systems for use in fuselage interior equipment and non-structural or secondary structural area.
It may be applied when referred to in the product standard or in a design specification.

This standard specifies the characteristics of self-locking bihexagonal nuts, with counterbore, in heat resisting nickel base alloy, passivated, MoS2 lubricated.
Classification: 1 550 MPa / 315 °C.

This European standard specifies the dimensions, mass, tolerances and static values of spring clamps for use in fuselage interior equipment and non-structural or secondary structural area. This standard part shall be used in conjunction with EN 4710-06 and EN 4710-07 as described in EN 4710-02.
The applicable temperature range is −55 °C to 85 °C.

This document specifies the characteristics of self-locking shank nuts in FE PA2601, silver plated on thread, for aerospace applications.
Classification: 1 100 MPa / 650 °C.