SIST EN IEC 60966-4-1:2024

SLOVENSKI STANDARD
01-junij-2024
Sestavi radiofrekvenčnih in koaksialnih kablov - 4-1. del: Okvirna podrobna
specifikacija za sestave poltogih koaksialnih kablov (IEC 60966-4-1:2024)
Radio frequency and coaxial cable assemblies - Part 4-1: Blank detail specification for
semi-rigid coaxial cable assemblies (IEC 60966-4-1:2024)
Konfektionierte Koaxial- und Hochfrequenzkabel - Teil 4-1: Vordruck für
Bauartspezifikation für halbstarre konfektionierte Koaxialkabel (IEC 60966-4-1:2024)
Cordons coaxiaux et cordons pour fréquences radioélectriques – Partie 4-1:
Spécification particulière-cadre pour cordons coaxiaux semi-rigides (IEC 60966-4-
1:2024)
Ta slovenski standard je istoveten z: EN IEC 60966-4-1:2024
ICS:
33.120.10 Koaksialni kabli. Valovodi Coaxial cables. Waveguides
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60966-4-1

NORME EUROPÉENNE
EUROPÄISCHE NORM April 2024
ICS 33.120.10 Supersedes EN 60966-4-1:2003
English Version
Radio frequency and coaxial cable assemblies - Part 4-1: Blank
detail specification for semi-rigid coaxial cable assemblies
(IEC 60966-4-1:2024)
Cordons coaxiaux et cordons pour fréquences Konfektionierte Koaxial- und Hochfrequenzkabel - Teil 4-1:
radioélectriques - Partie 4-1 : Spécification particulière- Vordruck für Bauartspezifikation für halbstarre
cadre pour cordons coaxiaux semi-rigides konfektionierte Koaxialkabel
(IEC 60966-4-1:2024) (IEC 60966-4-1:2024)
This European Standard was approved by CENELEC on 2024-04-16. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60966-4-1:2024 E

European foreword
The text of document 46/965/FDIS, future edition 3 of IEC 60966-4-1, prepared by IEC/TC 46 "Cables,
wires, waveguides, RF connectors, RF and microwave passive components and accessories" was
submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 60966-4-1:2024.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2025-01-16
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2027-04-16
document have to be withdrawn
This document supersedes EN 60966-4-1:2003 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60966-4-1:2024 was approved by CENELEC as a
European Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60068 series Environmental testing EN 60068 series
IEC 60966-1 2019 Radio frequency and coaxial cable EN IEC 60966-1 2019
assemblies - Part 1: Generic specification -
General requirements and test methods
IEC 60966-4 2024 Radio frequency and coaxial cable EN IEC 60966-4 2024
assemblies - Part 4: Sectional specification
for semi-rigid coaxial cable assemblies
IEC 61196-1-126 - Coaxial communication cables - Part 1- - -
126: Electrical test methods - Corona
extinction voltage
IEC 60966-4-1 ®
Edition 3.0 2024-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Radio frequency and coaxial cable assemblies –

Part 4-1: Blank detail specification for semi-rigid coaxial cable assemblies

Cordons coaxiaux et cordons pour fréquences radioélectriques –

Partie 4-1 : Spécification particulière-cadre pour cordons coaxiaux semi-rigides

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.120.10  ISBN 978-2-8322-8409-4

– 2 – IEC 60966-4-1:2024 © IEC 2024
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Instructions . 5
5 Detail specification . 7

IEC 60966-4-1:2024 © IEC 2024 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
RADIO FREQUENCY AND COAXIAL CABLE ASSEMBLIES –

Part 4-1: Blank detail specification for semi-rigid coaxial cable assemblies

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
IEC 60966-4-1 has been prepared by IEC technical committee 46: Cables, wires, waveguides,
RF connectors, RF and microwave passive components and accessories. It is an International
Standard.
This third edition cancels and replaces the second edition published in 2003. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) added Clause 1 "Scope";
b) added Clause 2 "Normative reference";
c) rewrote Clause 4 "Instructions";

– 4 – IEC 60966-4-1:2024 © IEC 2024
d) added "[6] Outline for semi-rigid cable assemblies", "[7] The relative position dimensions of
the interface", "[8] Maximum diameter of semi-flexible cable";
e) added "Corona extinction voltage";
f) modified "[19] Value", "[20] Remark".
The text of this International Standard is based on the following documents:
Draft Report on voting
46/965/FDIS 46/995/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
A list of all parts in the IEC 60966, published under the general title Radio frequency and coaxial
cable assemblies, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn, or
• revised.
IEC 60966-4-1:2024 © IEC 2024 – 5 –
RADIO FREQUENCY AND COAXIAL CABLE ASSEMBLIES –

Part 4-1: Blank detail specification for semi-rigid coaxial cable assemblies

1 Scope
This part of IEC 60966 is a blank detail specification that relates to semi-rigid coaxial cable
assemblies operating in the transverse electromagnetic mode (TEM).
The creation of a uniform layout and style of detail specifications is determined by the use of a
blank detail specification pro forma. The detail specification may be prepared by a national
organization, a manufacturer, or a user.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (includi
...