SIST EN 15512:2021/oprA1:2021
(Amendment)Steel static storage systems - Adjustable pallet racking systems - Principles for structural design
Steel static storage systems - Adjustable pallet racking systems - Principles for structural design
This European Standard specifies the structural design requirements applicable to all types of adjustable beam pallet rack systems fabricated from steel members intended for the storage of unit loads and subject to predominantly static loads. Both un-braced and braced systems are included.
This European Standard gives guidelines for the design of clad rack buildings where requirements are not covered in EN 1993. The requirements of this European Standard also apply to ancillary structures, where rack components are employed as the main structural members.
This European Standard does not cover other generic types of storage structures. Specifically, this European Standard does not apply to mobile storage systems, drive-in, drive-through and cantilever racks or static steel shelving systems, nor does this European Standard establish specific design rules for the assessment of racking in seismic areas.
Ortsfeste Regalsysteme aus Stahl - Verstellbare Palettenregale - Grundlagen der statischen Bemessung
No scope available
Systèmes de stockage statiques en acier - Systèmes de rayonnages à palettes réglables - Principes applicables au calcul des structures
Stabilni jekleni sistemi za skladiščenje - Sistemi za nastavljive regale za palete - Načela dimenzioniranja - Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 15512:2021/oprA1:2021
01-julij-2021
Stabilni jekleni sistemi za skladiščenje - Sistemi za nastavljive regale za palete -
Načela dimenzioniranja - Dopolnilo A1
Steel static storage systems - Adjustable pallet racking systems - Principles for structural
design
Ortsfeste Regalsysteme aus Stahl - Verstellbare Palettenregale - Grundlagen der
statischen Bemessung
Systèmes de stockage statiques en acier - Systèmes de rayonnages à palettes réglables
- Principes applicables au calcul des structures
Ta slovenski standard je istoveten z: EN 15512:2020/prA1
ICS:
53.080 Skladiščna oprema Storage equipment
SIST EN 15512:2021/oprA1:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 15512:2021/oprA1:2021
---------------------- Page: 2 ----------------------
SIST EN 15512:2021/oprA1:2021
DRAFT
EUROPEAN STANDARD
EN 15512:2020
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
May 2021
ICS 53.080
English Version
Steel static storage systems - Adjustable pallet racking
systems - Principles for structural design
Systèmes de stockage statiques en acier - Systèmes de Ortsfeste Regalsysteme aus Stahl - Verstellbare
rayonnages à palettes réglables - Principes applicables Palettenregale - Grundlagen der statischen Bemessung
au calcul des structures
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 344.
This draft amendment A1, if approved, will modify the European Standard EN 15512:2020. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15512:2020/prA1:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 15512:2021/oprA1:2021
EN 15512:2020/prA1:2021 (E)
Contents Page
European foreword . 3
1 Modification to 9.1.3.3 "Slab deformation limits bolted frames" . 4
2 Modification to 9.2.2.1 "General" . 4
3 Modification to E.4.3 "Bending and axial compression – buckling resistance of
member" . 4
4 Modification to N.1 "Dutch national legislative deviations" . 5
5 Modification to N.2 "Italian national legislative deviations" . 6
2
---------------------- Page: 4 ----------------------
SIST EN 15512:2021/oprA1:2021
EN 15512:2020/prA1:2021 (E)
European foreword
This document (EN 15512:2020/prA1:2021) has been prepared by Technical Committee CEN/TC 344
“Steel static storage systems”, the secretariat of which is held by UNI.
This document is currently submitted to the CEN Enquiry.
3
---------------------- Page: 5 ----------------------
SIST EN 15512:2021/oprA1:2021
EN 15512:2020/prA1:2021 (E)
1 Modification to 9.1.3.3 "Slab deformation limits bolted frames"
Replace the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.