SIST EN 61347-2-13:2014

SLOVENSKI STANDARD
SIST EN 61347-2-13:2014
01-december-2014
1DGRPHãþD
SIST EN 61347-2-13:2007
.UPLOQHVWLNDOQHQDSUDYH]DVLMDONHGHO3RVHEQH]DKWHYH]DHQRVPHUQRDOL
L]PHQLþQRQDSDMDQHHOHNWURQVNHNUPLOQHVWLNDOQHQDSUDYH]DPRGXOH/(',(&

Lamp controlgear - Part 2-13: Particular requirements for d.c. or a.c. supplied electronic
controlgear for LED modules
Geräte für Lampen - Teil 2-13: Besondere Anforderungen an gleich- oder
wechselstromversorgte elektronische Betriebsgeräte für LED-Module
Appareillages de lampes - Partie 2-13: Exigences particulières pour les appareillages
électroniques alimentés en courant continu ou en courant alternatif pour modules de
LED
Ta slovenski standard je istoveten z: EN 61347-2-13:2014
ICS:
29.130.01 Stikalne in krmilne naprave Switchgear and controlgear
na splošno in general
29.140.99 Drugi standardi v zvezi z Other standards related to
žarnicami lamps
SIST EN 61347-2-13:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61347-2-13:2014

---------------------- Page: 2 ----------------------

SIST EN 61347-2-13:2014


EUROPEAN STANDARD EN 61347-2-13

NORME EUROPÉENNE

EUROPÄISCHE NORM
October 2014
ICS 29.140.99 Supersedes EN 61347-2-13:2006
English Version
Lamp controlgear - Part 2-13: Particular requirements for d.c. or
a.c. supplied electronic controlgear for LED modules
(IEC 61347-2-13:2014)
Appareillages de lampes - Partie 2-13: Exigences Geräte für Lampen - Teil 2-13: Besondere Anforderungen
particulières pour les appareillages électroniques alimentés an gleich- oder wechselstromversorgte elektronische
en courant continu ou alternatif pour les modules de LED Betriebsgeräte für LED-Module
(CEI 61347-2-13:2014) (IEC 61347-2-13:2014)
This European Standard was approved by CENELEC on 2014-10-08. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.



European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 61347-2-13:2014 E

---------------------- Page: 3 ----------------------

SIST EN 61347-2-13:2014
EN 61347-2-13:2014 - 2 -

Foreword
The text of document 34C/1092/FDIS, future edition 2 of IEC 61347-2-13, prepared by SC 34C,
"Auxiliaries for lamps", of IEC TC 34, "Lamps and related equipment", was submitted to the IEC-
CENELEC parallel vote and approved by CENELEC as EN 61347-2-13:2014.
The following dates are fixed:
(dop) 2015-07-08
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2017-10-08
• latest date by which the national
standards conflicting with the
document have to be withdrawn

This document supersedes EN 61347-2-13:2006

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.

This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment Designed
for Use within Certain Voltage Limits (LVD - 2006/95/EC).

Endorsement notice
The text of the International Standard IEC 61347-2-13:2014 was approved by CENELEC as a European
Standard without any modification.

In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60051 Series NOTE Harmonised in EN 60051 Series.
IEC 60085:2004 NOTE Harmonised as EN 60085:2008.
IEC 60364-4-41:2005 NOTE Harmonised as HD 60364-4-41:2007.
IEC 60384-14:2005 NOTE Harmonised as EN 60384-14:2005.
IEC 60950-1:2005 NOTE Harmonised as EN 60950-1:2006.
IEC 61558-1:2005 NOTE Harmonised as EN 61558-1:2005.
IEC 61558-2-1:2007 NOTE Harmonised as EN 61558-2-1:2007.
IEC 61558-2-4:2009 NOTE Harmonised as EN 61558-2-4:2009.
IEC 61558-2-13:2009 NOTE Harmonised as EN 61558-2-13:2009.

---------------------- Page: 4 ----------------------

SIST EN 61347-2-13:2014
- 3 - EN 61347-2-13:2014

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD

applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61347-1 (mod) 2007 Lamp controlgear -- Part 1: General and EN 61347-1 2008
safety requirements
+A1 2010  +A1 2011
+A2 2012  +A2 2013
IEC 61347-2-7 2011 Lamp controlgear -- Part 2-7: Particular EN 61347-2-7 2012
requirements for battery supplied electronic
controlgear for emergency lighting (self-
contained)
IEC 61547 -  Equipment for general lighting purposes - EN 61547 -
EMC immunity requirements
IEC 61558 series - Safety of power transformers, power EN 61558 series -
supplies, reactors and similar products --
Part 1: General requirements and tests
IEC 61558-2-6 2009 Safety of transformers, reactors, power EN 61558-2-6 2009
supply units and similar products for supply
voltages up to 1 100 V -- Part 2-6: Particular
requirements and tests for safety isolating
transformers and power supply units
incorporating safety isolating transformers
IEC 61558-2-16 2009 Safety of transformers, reactors, power EN 61558-2-16 2009
supply units and similar products for
voltages up to 1 100 V -- Part 2-16:
Particular requirements and tests for switch
mode power supply units and transformers
for switch mode power supply units
IEC 62384 2006 D.C. or A.C. supplied electronic control gear EN 62384 2006
for LED modules - Performance
requirements

---------------------- Page: 5 ----------------------

SIST EN 61347-2-13:2014

---------------------- Page: 6 ----------------------

SIST EN 61347-2-13:2014



IEC 61347-2-13

®


Edition 2.0 2014-09




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Lamp controlgear –

Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear

for LED modules




Appareillage de lampes –

Partie 2-13: Exigences particulières pour les appareillages électroniques


alimentés en courant continu ou alternatif pour les modules de LED












INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX T


ICS 29.140.99 ISBN 978-2-8322-1849-5



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 61347-2-13:2014
– 2 – IEC 61347-2-13:2014 © IEC 2014
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
4 General requirements . 9
5 General notes on tests . 10
6 Classification . 10
7 Marking . 10
7.1 Mandatory marking . 10
7.2 Information to be provided if applicable . 10
8 Protection against accidental contact with live parts . 10
9 Terminals . 10
10 Provisions for protective earthing. 11
11 Moisture resistance and insulation . 11
12 Electric strength . 11
13 Thermal endurance test for windings of ballasts . 11
14 Fault conditions . 11
15 Transformer heating . 11
15.1 General . 11
15.2 Normal operation . 11
15.3 Abnormal operation . 11
16 Construction . 12
17 Creepage distances and clearances . 12
18 Screws, current-carrying parts and connections . 12
19 Resistance to heat, fire and tracking . 12
20 Resistance to corrosion . 12
Annex A (normative) Test to establish whether a conductive part is a live part which
may cause an electric shock . 13
Annex B (normative) Particular requirements for thermally protected lamp controlgear . 14
Annex C (normative) Particular requirements for electronic lamp controlgear with
means of protection against overheating . 15
Annex D (normative) Requirements for carrying out the heating tests of thermally
protected lamp controlgear . 16
Annex E (normative) Use of constant S other than 4 500 in t tests . 17
w
Annex F (normative) Draught-proof enclosure . 18
Annex G (normative) Explanation of the derivation of the values of pulse voltages . 19
Annex H (normative) Tests. 20
Annex I (normative) Particular additional requirements for SELV d.c. or a.c. supplied
electronic controlgear for LED modules . 21
Annex J (normative) Particular additional safety requirements for a.c., a.c./d.c. or d.c.
supplied electronic controlgear for emergency lighting . 22
J.1 General . 22

---------------------- Page: 8 ----------------------

SIST EN 61347-2-13:2014
IEC 61347-2-13:2014 © IEC 2014 – 3 –
J.2 Marking . 22
J.2.1 Mandatory markings . 22
J.2.2 Information to be provided if applicable . 22
J.3 General notes on tests . 22
J.4 Starting conditions . 23
J.5 Operating condition . 23
J.6 Emergency supply current . 23
J.7 EMC immunity. 23
J.8 Pulse voltage from central battery systems . 23
J.9 Tests for abnormal conditions . 24
J.10 Temperature cycling test and endurance test . 24
J.11 Functional safety (EOF ) . 24
x
Bibliography . 25

Table J.1 – Pulse voltages . 23

---------------------- Page: 9 ----------------------

SIST EN 61347-2-13:2014
– 4 – IEC 61347-2-13:2014 © IEC 2014
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

LAMP CONTROLGEAR –

Part 2-13: Particular requirements for d.c. or
a.c. supplied electronic controlgear for LED modules

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61347-2-13 has been prepared by subcommittee 34C: Auxiliaries
for lamps, of IEC technical committee 34: Lamps and related equipment.
This second edition cancels and replaces the first edition published in 2006. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition.
a) Replacement of the SELV-equivalent requirements by SELV requirements and reference
to the SELV requirements of Annex L in IEC 61347-1:2007/AMD2:2012.
b) Reference to IEC 61347-1 for the protection against accidental contact with live parts,
moisture resistance and insulation and electric strength.
c) New Annex J for emergency lighting requirements.

---------------------- Page: 10 ----------------------

SIST EN 61347-2-13:2014
IEC 61347-2-13:2014 © IEC 2014 – 5 –
The text of this standard is based on the following documents:
FDIS Report on voting
34C/1092/FDIS 34C/1106/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This standard shall be used in conjunction with IEC 61347-1.Where the requirements of any
of the clauses of IEC 61347-1 are referred to in this standard by the phrase "The
requirements of Clause n of IEC 61347-1:2007/AMD1:2010/AMD2:2012, apply", this phrase is
interpreted as meaning that all requirements of the clause in question of Part 1 apply, except
any which are clearly inapplicable to the specific type of lamp controlgear covered by this
particular part of IEC 61347-2.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
In this standard, the following print types are used:
– requirements: in roman type,
– test specifications: in italic type,
– notes: in small roman type.
A list of all parts in the IEC 61347, published under the general title Lamp controlgear can be
found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 11 ----------------------

SIST EN 61347-2-13:2014
– 6 – IEC 61347-2-13:2014 © IEC 2014
INTRODUCTION
This second edition of IEC 61347-2-13 is published in conjunction with IEC 61347-1. The
formatting into separately published parts provides for ease of future amendments and
revisions. Additional requirements will be added as and when a need for them is recognized.
This standard and the parts which make up IEC 61347-2, in referring to any of the clauses of
IEC 61347-1 specify the extent to which such a clause is applicable and the order in which the
tests are to be performed; they also include additional requirements as necessary. All parts
which make up IEC 61347-2 are self-contained and therefore do not include references to
each other.

---------------------- Page: 12 ----------------------

SIST EN 61347-2-13:2014
IEC 61347-2-13:2014 © IEC 2014 – 7 –
LAMP CONTROLGEAR –

Part 2-13: Particular requirements for d.c. or
a.c. supplied electronic controlgear for LED modules



1 Scope
This part of IEC 61347 specifies particular safety requirements for electronic controlgear for
use on d.c. or a.c. supplies up to 1 000 V (a.c. at 50 Hz or 60 Hz) and at an output frequency
which can deviate from the supply frequency, associated with LED modules.
Controlgear for LED modules specified in this standard are designed to provide constant
voltage or current at SELV or higher voltages. Deviations from the pure voltage and current
types do not exclude the gear from this standard.
The annexes of IEC 61347-1 which are applicable according to this Part 2-13 and using the
word “lamp” are understood to also comprise LED modules.
Particular requirements for SELV controlgear are given in Annex I.
Performance requirements are covered by IEC 62384.
Plug-in controlgear, being part of the luminaire, are covered as for built-in controlgear by the
additional requirements of the luminaire standard.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 61347-1:2007, Lamp controlgear – Part 1: General and safety requirements
Amendment 1:2010
Amendment 2:2012
IEC 61347-2-7:2011, Lamp controlgear – Part 2-7: Particular requirements for battery
supplied electronic controlgear for emergency lighting (self-contained)
IEC 61547, Equipment for general lighting purposes – EMC immunity requirements
IEC 61558 (all parts), Safety of power transformers, power supplies, reactors and similar
products
IEC 61558-2-6:2009, Safety of transformers, reactors, power supply units and similar products
for supply voltages up to 1 100 V – Part 2-6: Particular requirements and tests for safety
isolating transformers and power supply units incorporating safety isolating transformers
IEC 61558-2-16:2009, Safety of transformers, reactors, power supply units and similar
products for supply voltages up to 1 100 V – Part 2-16: Particular requirements and tests for
switch mode power supply units and transformers for switch mode power supply units

---------------------- Page: 13 ----------------------

SIST EN 61347-2-13:2014
– 8 – IEC 61347-2-13:2014 © IEC 2014
IEC 62384:2006, DC or AC supplied electronic controlgear for LED modules – Performance
requirements
3 Terms and definitions
For the purpose of this document, the terms and definitions given in IEC 61347-1, as well as
the following apply.
3.1
electronic controlgear for LED modules
unit inserted between the supply and one or more LED modules which serves to supply the
LED module(s) with its (their) rated voltage or rated current
Note 1 to entry: The unit may consist of one or more separate components and may include means for dimming,
correcting the power factor and suppressing radio interference, and futher control functions.
Note 2 to entry: The controlgear consists of a power supply and a control unit.
Note 3 to entry: The controlgear may be partly or totally integrated in the LED module.
3.2
d.c. or a.c. supplied controlgear
controlgear that includes stabilising elements for operating one or more LED module(s)
3.3
SELV controlgear
controlgear providing an SELV output isolated from the supply mains by means such as a
safety isolating transformer, as specified in IEC 61558-2-6 and IEC 61558-2-16
3.4
associated controlgear
controlgear designed to supply specific appliance(s) or equipment, incorporated or not
incorporated
EXAMPLE: An electronic controlgear within an emergency unit where it is assigned in a one-to-one relation to a
battery driven ballast.
3.5
plug-in controlgear
controlgear incorporated in an enclosure provided with an integral plug as the means of
connection of the electrical supply
3.6
rated output voltage for constant voltage controlgear
output voltage, at rated supply voltage, rated frequency and at rated output power, assigned
to the controlgear
3.7
rated output current for constant current controlgear
output current, at rated supply voltage, rated frequency and at rated output power, assigned
to the controlgear
3.8
light emitting diode
LED
solid state device embodying a p-n junction, emitting optical radiation when excited by an
electric current
Note 1 to entry: This definition is independent from the existence of enclosure(s) and of terminals.

---------------------- Page: 14 ----------------------

SIST EN 61347-2-13:2014
IEC 61347-2-13:2014 © IEC 2014 – 9 –
[SOURCE: IEC 60050-845:1987, 845.04.40]
3.9
LED module
light source having no cap, incorporating one or more LED package(s) on a printed circuit
board, and possibly including one or more of the following:
electrical, optical, mechanical, and thermal components, interfaces and controlgear
Note 1 to entry: A LED module may be integrated (LEDi module, Type 1) or semi-integrated (LEDsi module,
Type 2) or nonintegrated (LEDni module, Type 3).
Note 2 to entry: The LED module is usually designed to be part of a LED lamp or LED luminaire.
3.10
maximum output voltage
maximum voltage which can occur between the output terminals for constant current
controlgear in any load condition
3.11
emergency lighting
lighting provided for use when the supply to the normal lighting fails; it includes escape
lighting and standby lighting
3.12
rated emergency supply voltage or voltage range
rated voltage or voltage range claimed by the manufacturer where the controlgear will operate
according specification
3.13
emergency output factor
EOF
x
ratio of the electrical output parameter when the control gear under test is operated in
emergency mode to the output electrical parameter when the control gear is operated with the
normal lighting conditions
Note 1 to entry: The electrical output parameter can be current (EOF ), voltage (EOF ) or power (EOF ) at the
I V W
output(s) of the control gear (depending on the module it could be constant current, constant voltage or constant
power).
Note 2 to entry: The emergency output factor is the minimum of the values measured at the appropriate time after
failure of the normal supply and continuously.
3.14
emergency supply current
rated supply current of the control gear operating in the emergency mode
4 General requirements
The requirements of Clause 4 of IEC 61347-1:2007/AMD2:2012 apply, together with the
following additional requirements.
– Controlgear providing SELV shall comply with the requirements of Annex I. This includes
insulation resistance, electric strength, creepage distances and clearance between
primary and secondary circuits.
– If a separating, isolating or autotransformer is used, it shall comply with the relevant parts
of IEC 61558. If, however, insulated winding wires are used for controlgear with an input
voltage of up to 300 V, the dielectric strength test voltage is limited to 3 kV for raw
material.

---------------------- Page: 15 ----------------------

SIST EN 61347-2-13:2014
– 10 – IEC 61347-2-13:2014 © IEC 2014
5 General notes on tests
The requirements of Clause 5 of IEC 61347-1:2007/AMD2:2012 appl
...