SIST EN IEC 60317-0-3:2024

SLOVENSKI STANDARD
01-december-2024
Specifikacije za posebne vrste navijalnih žic - 0-3. del: Splošne zahteve - Emajliran
okrogel aluminijev vodnik (IEC 60317-0-3:2024)
Specifications for particular types of winding wires - Part 0-3: General requirements -
Enamelled round aluminium wire (IEC 60317-0-3:2024)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-3:
Allgemeine Anforderungen - Lackisolierte Runddrähte aus Aluminiumdraht (IEC 60317-0
-3:2024)
Spécifications pour types particuliers de fils de bobinage - Partie 0-3: Exigences
générales - Fil de section circulaire en aluminium émaillé (IEC 60317-0-3:2024)
Ta slovenski standard je istoveten z: EN IEC 60317-0-3:2024
ICS:
29.060.10 Žice Wires
77.150.10 Aluminijski izdelki Aluminium products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 60317-0-3

NORME EUROPÉENNE
EUROPÄISCHE NORM October 2024
ICS 29.060.10 Supersedes EN 60317-0-3:2008;
EN 60317-0-3:2008/A1:2013;
EN 60317-0-3:2008/A2:2019
English Version
Specifications for particular types of winding wires - Part 0-3:
General requirements - Enamelled round aluminium wire
(IEC 60317-0-3:2024)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 0-3: Exigences générales - Fil de section circulaire Wickeldrähten - Teil 0-3: Allgemeine Anforderungen -
en aluminium émaillé Lackisolierte Runddrähte aus Aluminium
(IEC 60317-0-3:2024) (IEC 60317-0-3:2024)
This European Standard was approved by CENELEC on 2024-10-16. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60317-3:2024 E

European foreword
The text of document 55/2049/FDIS, future edition 4 of IEC 60317-0-3, prepared by TC 55 "Winding
wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2025-10-31
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2027-10-31
document have to be withdrawn
This document supersedes EN 60317-0-3:2008 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 60317-0-3:2024 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60264 (series) NOTE Approved as EN 60264 (series)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60172 - Test procedure for the determination of the EN IEC 60172 -
temperature index of enamelled and tape
wrapped winding wires
IEC 60317 series Specifications for particular types of EN 60317 series
winding wires
IEC 60851 series Winding wires - Test methods EN IEC 60851 series
ISO 3 - Preferred numbers - Series of preferred - -
numbers
ASTM B233-97 - Standard Specification for Aluminum 1350 - -
Drawing Stock for Electrical Purposes
Aluminium and aluminium alloys - Drawing EN 1715-2 -
stock - Part 2: Specific requirements for
electrical applications
IEC 60317-0-3 ®
Edition 4.0 2024-09
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specifications for particular types of winding wires –

Part 0-3: General requirements – Enamelled round aluminium wire

Spécifications pour types particuliers de fils de bobinage –

Partie 0-3: Exigences générales – Fil de section circulaire en aluminium émaillé

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.060.10  ISBN 978-2-8322-9617-2

– 2 – IEC 60317-0-3:2024 © IEC 2024
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions, general notes, and appearance . 7
3.1 Terms and definitions . 7
3.2 General notes . 8
3.2.1 Methods of test . 8
3.2.2 Winding wire . 9
3.3 Appearance . 9
4 Dimensions. 9
4.1 Conductor diameter . 9
4.2 Out of roundness of conductor . 11
4.3 Minimum increase in diameter due to the insulation and the bonding layer . 11
4.3.1 Enamelled wires without a bonding layer . 11
4.3.2 Enamelled wires with a bonding layer . 11
4.4 Maximum overall diameter . 11
4.4.1 Enamelled wires without a bonding layer . 11
4.4.2 Enamelled wires with a bonding layer . 12
5 Electrical resistance . 12
6 Elongation . 12
7 Springiness . 12
8 Flexibility and adherence . 12
8.1 Mandrel winding test (nominal conductor diameters up to and including
1,600 mm) . 12
8.2 Stretching test (nominal conductor diameters over 1,600 mm) . 13
8.3 Jerk test (nominal conductor diameters up to and including 1,000 mm) . 13
8.4 Peel test (nominal conductor diameters over 1,000 mm) . 13
9 Heat shock . 13
9.1 Nominal conductor diameters up to and including 1,600 mm . 13
9.2 Nominal conductor diameters over 1,600 mm . 13
10 Cut-through . 13
11 Resistance to abrasion . 13
12 Resistance to solvents . 13
13 Breakdown voltage . 14
13.1 General . 14
13.2 Nominal conductor diameters up to and including 2,500 mm . 14
13.3 Nominal conductor diameters over 2,500 mm . 14
14 Continuity of insulation (nominal conductor diameters up to and including
1,600 mm) . 15
15 Temperature index . 15
16 Resistance to refrigerants . 15
17 Solderability . 15
18 Heat or solvent bonding . 15
19 Dielectric dissipation factor . 16

IEC 60317-0-3:2024 © IEC 2024 – 3 –
20 Resistance to transformer oil . 16
21 Loss of mass . 16
23 Pin hole test . 16
30 Packaging . 16
Annex A (informative) Dimensions for intermediate nominal conductor diameters
(R 40) . 17
A.1 General . 17
A.2 Enamelled wires without a bonding layer. 17
A.3 Enamelled wires with a bonding layer . 18
Annex B (normative) Method for the calculation of linear resistance . 19
Annex C (informative) Resistance . 20
Bibliography . 21

Table 1 – Dimensions of enamelled wires (R 20). 10
Table 2 – Dimensions of enamelled wires with a bonding layer (R 20) . 11
Table 3 – Elongation . 12
Table 4 – Mandrel winding . 12
Table 5 – Heat shock . 13
Table 6 – Breakdown voltage . 14
Table 7 – Breakdown voltage . 15
Table 8 – Continuity of insulation . 15
Table A.2 – Dimensions of enamelled wires with a bonding layer (R 40) . 18
Table C.1 – Electrical resistances . 20

– 4 – IEC 60317-0-3:2024 © IEC 2024
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –

Part 0-3: General requirements – Enamelled round aluminium wire

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
IEC 60317-0-3 has been prepared by IEC technical committee 55: Winding wires. It is an
International Standard.
This fourth edition cancels and replaces the third edition published in 2008, Amendment 1:2013
and Amendment 2:2019. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) Revision to Clause 7, designating the test as inappropriate;
b) Revision to Clause 10, designating the test as inappropriate.

IEC 60317-0-3:2024 © IEC 2024 – 5 –
The text of this International Standard is based on the following documents:
Draft Report on voting
55/2049/FDIS 55/2054/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
A list of all parts in the IEC 60317 series, published under the general title Specifications for
particular types of winding wires, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn, or
• revised.
– 6 – IEC 60317-0-3:2024 © IEC 2024
INTRODUCTION
The International Electrotechnical Commission (IEC) draws attention to the fact that it is claimed
that compliance with this document may involve the use of a patent. IEC takes no position
concerning the evidence, validity, and scope of this patent right.
The holder of this patent right has assured IEC that s/he is willing to negotiate licences under
reasonable and non-discriminatory terms and conditions with applicants throughout the world.
In this respect, the statement of the holder of this patent right is registered with IEC. Information
may be obtained from the patent database available at patents.iec.ch/.
Attention is drawn to the possibility that some of the elements of this document may be the
subject of patent rights other than those in the patent database. IEC shall not be held
responsible for identifying any or all such patent rights.
This part of IEC 60317 is one of a series that deals with insulated wires used for windings in
electrical equipment. The series has three groups describing
1) winding wires and test methods (IEC 60851);
2) specifications for particular types of winding wires (IEC 60317);
3) packaging of winding wires (IEC 60264).

IEC 60317-0-3:2024 © IEC 2024 – 7 –
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –

Part 0-3: General requirements – Enamelled round aluminium wire

1 Scope
This par
...