SIST EN 62319-1-1:2005

SLOVENSKI SIST EN 62319-1-1:2005

STANDARD
december 2005
Polimerni termistorji – Neposredno ogrevani s pozitivnim temperaturnim
koeficientom – 1-1. del: Okvirna podrobna specifikacija – Uporaba z
omejevanjem toka (IEC 62319-1-1:2005)
Polymeric thermistors – Directly heated positive step function temperature
coefficient – Part 1-1: Blank detail specification – Current limiting application (IEC
62319-1-1:2005)
ICS 31.040.30 Referenčna številka
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

EUROPEAN STANDARD EN 62319-1-1
NORME EUROPÉENNE
EUROPÄISCHE NORM March 2005
ICS 31.040.30
English version
Polymeric thermistors -
Directly heated positive step function temperature coefficient
Part 1-1: Blank detail specification -
Current limiting application
(IEC 62319-1-1:2005)
Thermistances polymères - Temperaturabhängige Widerstände
Coefficient de température positif aus Polymerwerkstoffen -
de fonction échelon à chauffage direct Direkt geheizte temperaturabhängige
Partie 1-1: Spécification particulière cadre - Widerstände mit positivem
Application de limitation de courant Temperaturkoeffizienten
(CEI 62319-1-1:2005) Teil 1-1: Vordruck
für die Bauartspezifikation -
Anwendung für die Strombegrenzung
(IEC 62319-1-1:2005)
This European Standard was approved by CENELEC on 2005-02-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 62319-1-1:2005 E
Foreword
The text of document 40/1506/FDIS, future edition 1 of IEC 62319-1-1, prepared by IEC TC 40,
Capacitors and resistors for electronic equipment, was submitted to the IEC-CENELEC parallel vote
and was approved by CENELEC as EN 62319-1-1 on 2005-02-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2005-12-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2008-02-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 62319-1-1:2005 was approved by CENELEC as a
European Standard without any modification.
__________
- 3 - EN 62319-1-1:2005
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60068 Series Environmental testing EN 60068 Series

1)
IEC 60410 - Sampling plans and procedures for - -
inspection by attributes
1) 2)
IEC 62319-1 - Polymeric thermistors - Directly heated EN 62319-1 2005
positive step function temperature
coefficient
Part 1: Generic specification
1)
Undated reference.
2)
Valid edition at date of issue.

INTERNATIONAL IEC
STANDARD 62319-1-1
First edition
2005-02
Polymeric thermistors –
Directly heated positive step function
temperature coefficient –
Part 1-1:
Blank detail specification –
Current limiting application
 IEC 2005  Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale
M
International Electrotechnical Commission
Международная Электротехническая Комиссия
For price, see current catalogue

– 2 – 62319-1-1  IEC:2005(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
POLYMERIC THERMISTORS –
DIRECTLY HEATED POSITIVE STEP FUNCTION
TEMPERATURE COEFFICIENT –
Part 1-1: Blank detail specification –
Current limiting application
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62319-1-1 has been prepared by IEC technical committee 40:
Capacitors and resistors for electronic equipment.
The text of this standard is based on the following documents:
FDIS Report on voting
40/1506/FDIS 40/1535/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

62319-1-1  IEC:2005(E) – 3 –
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.

– 4 – 62319-1-1  IEC:2005(E)
POLYMERIC THERMISTORS –
DIRECTLY HEATED POSITIVE STEP FUNCTION
TEMPERATURE COEFFICIENT –
Part 1-1: Blank detail specification –
Current limiting application
INTRODUCTION
Blank detail specification
A blank detail specification is a supplementary document to the generic specification and
contains requirements for style and layout and minimum content of detail specifications. Detail
specifications not complying with these requirements shall not be considered as being in
accordance with IEC specifications nor shall they so be described.
In the preparation of detail specifications, the content of 4.1 of the generic specification shall
be taken into account.
The numbers between brackets on the first page correspond to the following information
which shall be inserted in the position indicated.
Identification of the detail specification

[1] The “International Electrotechnical Commission” or the National Organisation under
whose authority the detail specification is drafted.
[2] The IEC or National Standards number of the detail specification, date of issue and any
other information required by the national system.
[3] The number and issue number of the IEC or national generic specification.
[4] The IEC number of the blank detail specification.

Identification of the thermistor

[5] A short description of the type of thermistor.
[6] Information on typical construction (if applicable).
NOTE When the thermistor is not designed for use on printed boards, this should be stated in the detail
specification in this position.
[7] Outline drawing with main dimensions which are important for the interchangeability
and/or reference to the national or international documents for outlines. Alternatively, this
drawing may be given in the annex to the detail specification.
[8] Application or group of applications covered and/or assessment level.
[9] Reference data on the most important properties, to allow comparison between the various
thermistor types.
62319-1-1  IEC:2005(E) – 5 –
[1] IEC 62319-1-1-XXX [2]
QC XXXXXX-XXX
ELECTRONIC COMPONENTS OF ASSESSED QUALITY IN IEC 62319-1-1 [4]
ACCORDANCE WITH: QC XXXXXX
[3]
POLYMERIC POSITIVE
TEMPERATURE COEFFICIENT [5]
THERMISTORS FOR CURRENT
Outline drawing: (see Table 1)
LIMITING APPLICATION
(… angle projection)
[7]
[6]
Assessment level(s): EZ [8]
(Other shapes are permitted within the dimensions given)

NOTE For [1] to [9] see preceding page.

Information on the availability of components qualified to
[9]
this detail specification is given in IEC QC 001005.

1 General data
1.1 Method(s) of mounting (to be inserted)
See 4.9 of IEC 62319-1.
1.2 Dimensions
All dimensions are in millimetres or inches and millimetres; it shall be stated which
dimensions are suitable for gauging.
Dimensional drawing(s) shall be given in the detail specification. If necessary, the dimensions
may be listed in tabular form with reference to styles or codes.
1.3 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including
...