SIST EN 60603-14:2003

SLOVENSKI SIST EN 60603-14:2003

STANDARD
oktober 2003
Connectors for frequencies below 3 MHz for use with printed boards - Part 14:
Detail specification for circular connectors for low-frequency audio and video
applications such as audio, video and audio-visual equipment (IEC 60603-14:1998)
ICS 31.220.10 Referenčna številka
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

NORME
CEI
INTERNATIONALE
IEC
60603-14
INTERNATIONAL
Première édition
STANDARD
First edition
1998-02
Connecteurs pour fréquences inférieures
à 3 MHz pour utilisation avec cartes imprimées –
Partie 14:
Spécification particulière pour les connecteurs
circulaires pour applications audio et vidéo
en basse fréquence tels que les équipements
audio, vidéo et audiovisuels
Connectors for frequencies below 3 MHz
for use with printed boards –
Part 14:
Detail specification for circular connectors for
low-frequency audio and video applications
such as audio, video and audio-visual equipment
 IEC 1998 Droits de reproduction réservés  Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in
utilisée sous quelque forme que ce soit et par aucun any form or by any means, electronic or mechanical,
procédé, électronique ou mécanique, y compris la photo- including photocopying and microfilm, without permission in
copie et les microfilms, sans l'accord écrit de l'éditeur. writing from the publisher.
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: +41 22 919 0300 e-mail: inmail@iec.ch IEC web site http: //www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale
PRICE CODE N
International Electrotechnical Commission
Pour prix, voir catalogue en vigueur
For price, see current catalogue

60603-14 © IEC:1998 – 3 –
CONTENTS
Page
FOREWORD . 5
Clause
1 Scope . 7
2 Normative references . 7
3 IEC type designation . 7
4 Isometric view . 9
5 Dimensions . 11
5.1 General. 11
5.2 Dimensions of free connectors . 11
5.3 Dimensions of fixed connectors. 13
6 Gauges . 15
6.1 Gauge for fixed connectors . 15
6.2 Gauge for free connectors. 17
7 Characteristics . 17
7.1 Climatic category . 17
7.2 Electrical. 17
7.3 Mechanical. 19
8 Test schedule . 21
8.1 General. 21
8.2 Tests . 23

60603-14 © IEC:1998 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
–––––––––
CONNECTORS FOR FREQUENCIES BELOW 3 MHz FOR USE
WITH PRINTED BOARDS –
Part 14: Detail specification for circular connectors for
low-frequency audio and video applications such as audio,
video and audio-visual equipment
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization
for Standardization (ISO) in accordance with conditions determined by agreement between the two
organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical reports or guides and they are accepted by the National Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60603-14 has been prepared by subcommittee 48B: Connectors, of
IEC technical committee 48: Electromechanical components and mechanical structures for
electronic equipment.
The text of this standard is based on the following documents:
FDIS Report on voting
48B/655/FDIS 48B/666/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.

60603-14 © IEC:1998 – 7 –
CONNECTORS FOR FREQUENCIES BELOW 3 MHz FOR USE
WITH PRINTED BOARDS –
Part 14: Detail specification for circular connectors for
low-frequency audio and video applications such as audio,
video and audio-visual equipment
1 Scope
This part of IEC 60603 applies to circular connectors for low-frequency audio and video
applications such as audio, video and audio-visual equipment.
The object of this part of IEC 60603 is to specify the dimensions and the general requirements
and tests for the circular connectors for use in audio, video and audio-visual equipment.
2 Normative references
The following normative documents contain provisions which, through reference in this text,
constitute provisions of this part of IEC 60603. At the time of publication, the editions indicated
were valid. All normative documents are subject to revision, and parties to agreements based
on this part of IEC 60603 are encouraged to investigate the possibility of applying the most
recent editions of the normative documents indicated below. Members of IEC and ISO maintain
registers of currently valid International Standards.
IEC 60512-2:1985, Electromechanical components for electronic equipment; basic testing
procedures and measuring methods – Part 2: General examination, electrical continuity and
contact resistance tests, insulation tests and voltage stress tests
IEC 60512-5:1992, Electromechanical components for electronic equipment; basic testing
procedures and measuring methods – Part 5: Impact tests (free components), static load tests
(fixed components), endurance tests and overload tests
IEC 60512-7:1993, Electromechanical components for electronic equipment; basic testing
procedures and measuring methods – Part 7: Mechanical operating tests and seali
...