SIST EN 62841-3-12:2019
(Main)Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery - Safety - Part 3-12: Particular requirements for transportable threading machines (IEC 62841-3-12:2017)
Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery - Safety - Part 3-12: Particular requirements for transportable threading machines (IEC 62841-3-12:2017)
IEC 62841-3-12:2017 applies to transportable threading machines. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This Part 3-12 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen – Sicherheit - Teil 3-12: Besondere Anforderungen für transportable Gewindeschneidmaschinen (IEC 62841-3-12:2017)
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 3-12: Exigences particulières relatives aux machines à fileter portables (IEC 62841-3-12:2017)
IEC 62481-3-12:2017 s'applique aux machines à fileter portables. La tension assignée est inférieure à 3 700 W. Les limites d'application de la présente Norme aux outils fonctionnant sur batterie sont indiquées dans l’annexe K. La présente Norme traite des dangers présentés par les outils, encourus par tous les individus dans l'utilisation normale et dans l'utilisation impropre raisonnablement prévisible de ces outils. Les outils électroportatifs, qui peuvent être montés sur un support de travail pour être utilisés comme outils installés à poste fixe sans aucune modification de l'outil lui-même, sont compris dans le domaine d'application de la présente Norme et la combinaison d'un outil portatif et d'un support est considérée comme un outil portable, donc couvert par la Partie 3 applicable.
La présente Partie 3-12 doit être utilisée conjointement avec la première édition de l'IEC 62841-1 (2014).
L'attention des Comités Nationaux est attirée sur le fait que les fabricants d'appareils et les organismes d'essai peuvent avoir besoin d'une période transitoire après la publication d'une nouvelle publication IEC, ou d'une publication amendée ou révisée, pour fabriquer des produits conformes aux nouvelles exigences et pour adapter leurs équipements aux nouveaux essais ou aux essais révisés.
Le comité recommande que le contenu de cette publication soit entériné au niveau national au plus tôt 36 mois après la date de publication.
Mots clés: machines à fileter, outils portatifs, sécurité
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 3-12. del: Posebne zahteve za prenosne rezalnike navojev (IEC 62841-3-12:2017)
IEC 62841-3-12:2017 se uporablja za prenosne rezalnike navojev. Nazivna napetost enofaznih orodij na izmenični ali enosmerni tok ne presega 250 V, trifaznih orodij na izmenični tok pa 480 V. Nazivna vhodna moč ne presega 3700 W. Omejitve uporabnosti tega standarda za baterijska orodja so podane v dodatku K. Ta standard obravnava nevarnosti, ki so jim ljudje izpostavljeni pri običajni uporabi orodij in pričakovani nepravilni uporabi orodij. Ročna električna orodja, ki jih je mogoče pritrditi na opornik ali delovno stojalo, kjer se jih brez kakršnih koli sprememb samega orodja uporablja kot fiksna orodja, spadajo na področje uporabe tega standarda. Kombinacija ročnega orodja in takšnega stojala se obravnava kot prenosno orodje, ki je zajeto v ustreznem 3. delu. Ta del 3-12 je treba uporabljati v povezavi s prvo izdajo standarda IEC 62841-1:2014. Nacionalni odbori morajo upoštevati, da bodo proizvajalci opreme in organizacije za preskušanje morda potrebovali prehodno obdobje po objavi nove, spremenjene ali popravljene objave IEC, da bodo lahko izdelovali izdelke v skladu z novimi zahtevami in se opremili za izvajanje novih ali spremenjenih preskusov. Odbor priporoča, da se vsebina te objave sprejme v nacionalno uporabo najpozneje 36 mesecev od datuma objave.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 62841-3-12:2019
01-september-2019
Nadomešča:
SIST EN 61029-2-12:2011
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 3-
12. del: Posebne zahteve za prenosne rezalnike navojev (IEC 62841-3-12:2017)
Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden
Machinery - Safety - Part 3-12: Particular requirements for transportable threading
machines (IEC 62841-3-12:2017)
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und
Rasen- und Gartenmaschinen – Sicherheit - Teil 3-12: Besondere Anforderungen für
transportable Gewindeschneidmaschinen (IEC 62841-3-12:2017)
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses -
Sécurité - Partie 3-12: Exigences particulières relatives aux machines à fileter portables
(IEC 62841-3-12:2017)
Ta slovenski standard je istoveten z: EN 62841-3-12:2019
ICS:
25.100.50 Navojna rezalna orodja Taps and threading dies
25.140.20 Električna orodja Electric tools
SIST EN 62841-3-12:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 62841-3-12:2019
---------------------- Page: 2 ----------------------
SIST EN 62841-3-12:2019
EUROPEAN STANDARD EN 62841-3-12
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2019
ICS 25.140.20
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 3-12: Particular
requirements for transportable threading machines
(IEC 62841-3-12:2017, modified)
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 3-12: Exigences transportable Werkzeuge und Rasen- und
particulières relatives aux machines à fileter portables Gartenmaschinen - Sicherheit - Teil 3-12: Besondere
(IEC 62841-3-12:2017) Anforderungen für transportable
Gewindeschneidmaschinen
(IEC 62841-3-12:2017, modifiziert)
This European Standard was approved by CENELEC on 2017-09-27. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62841-3-12:2019 E
---------------------- Page: 3 ----------------------
SIST EN 62841-3-12:2019
---------------------- Page: 4 ----------------------
SIST EN 62841-3-12:2019
EN 62841-3-12:2019 (E)
European foreword
The text of document 116/338/FDIS, future edition 1 of IEC 62841-3-12, prepared by IEC/TC 116 "Safety of
motor-operated electric tools." was submitted to the IEC-CENELEC parallel vote and approved by CENELEC
as EN 62841-3-12:2019.
A draft amendment, which covers common modifications to IEC 62841-3-12 (116/338/FDIS), was prepared
by CLC/TC 116," Safety of motor-operated electric tools" and approved by CENELEC.
The following dates are fixed:
• latest date by which this document has to be implemented at (dop) 2019-12-21
national level by publication of an identical national standard
or by endorsement
• latest date by which the national standards conflicting with (dow) 2023-06-21
this document have to be withdrawn
This document supersedes EN 61029-2-12:2011.
This European Standard is divided into four parts:
Part 1: General requirements which are common to most hand-held electric motor operated tools (for the
purpose of this standard referred to simply as tools) which could come within the scope of this
standard;
Part 2, 3 or 4: Requirements for particular types of tools which either supplement or modify the requirements
given in Part 1 to account for the particular hazards and characteristics of these specific tools.
This Part 3-12 is to be used in conjunction with EN 62841-1:2015.
This Part 3-12 supplements or modifies the corresponding clauses in EN 62841-1:2015, so as to convert it
into the European Standard: Particular requirements for transportable threading machines.
Where a particular subclause of Part 1 is not mentioned in this Part 3-12, that subclause applies as far as
relevant. When this standard states "addition", "modification" or "replacement", the relevant text in Part 1 is
to be adapted accordingly.
The following print types are used:
— requirements; in roman type
— test specifications: in italic type;
— notes: in smaller roman type.
The terms defined in Clause 3 are printed in bold typeface.
Subclauses, notes, tables and figures which are additional to those in Part 1 are numbered starting from 101.
Clauses, subclauses, notes, tables, figures and annexes which are additional to those in
IEC 62841-3-12:2017 are prefixed “Z”.
This European Standard follows the overall requirements of EN ISO 12100.
2
---------------------- Page: 5 ----------------------
SIST EN 62841-3-12:2019
EN 62841-3-12:2019 (E)
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission and
the European Free Trade Association and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s), see informative Annex ZZ, which is an integral part of this
document.
Compliance with the clauses of Part 1 together with this Part 3-12 provides one means of conforming with
the essential health and safety requirements of the Directive concerned.
Endorsement notice
The text of the International Standard IEC 62841-3-12:2017 was approved by CENELEC as a European
Standard with agreed common modifications.
3
---------------------- Page: 6 ----------------------
SIST EN 62841-3-12:2019
EN 62841-3-12:2019 (E)
COMMON MODIFICATIONS
1 Modifications to Clause 8, "Marking and instructions"
Add the following after 8.14.2 b):
8.14.2 Za) Replacement of items 3, 4 and 5 with the following:
3) The following information:
— that the declared noise emission value(s) have been measured in accordance with a standard test
method and may be used for comparing one tool with another;
— that the declared noise emission value(s) may also be used in a preliminary assessment of
exposure.
4) A warning:
— that the noise emissions during actual use of the power tool can differ from the declared values
depending on the ways in which the tool is used especially what kind of workpiece is processed;
and
— of the need to identify safety measures to protect the operator that are based on an estimation of
exposure in the actual conditions of use (taking account of all parts of the operating cycle such as
the times when the tool is switched off and when it is running idle in addition to the trigger time).
2 Modifications to Annex I, "Measurement of noise and vibration emissions"
Replace the title of Annex I with the following:
Annex I
(normative)
Measurement of noise and vibration emissions
and delete the note.
3 Addition of Annexes ZA and ZZ
Add the following Annexes ZA and ZZ:
4
---------------------- Page: 7 ----------------------
SIST EN 62841-3-12:2019
EN 62841-3-12:2019 (E)
"Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
1
IEC 60061 2005 Lamp caps and holders together with gauges - -
for the control of interchangeability and safety
IEC 60065 2001 Audio, video and similar electronic apparatus - -
- Safety requirements
+ A1 2005 - -
+ A2 2010 - -
IEC 60068-2-75 1997 Environmental testing -- Part 2-75: Tests - - -
Test Eh: Hammer tests
1
IEC/TR 60083 2015 Plugs and socket-outlets for domestic and - -
similar general use standardized in member
countries of IEC
IEC 60085 2007 Electrical insulation - Thermal evaluation and EN 60085 2008
designation
IEC 60127 series Miniature fuses EN 60127 series
IEC 60227 series Polyvinyl chloride insulated cables of rated - -
voltages up to and including 450/750 V
IEC 60238 - Edison screw lampholders EN IEC 60238 2018
IEC 60245 series Rubber insulated cables - Rated voltages up - -
to and including 450/750 V
IEC 60252-1 - AC motor capacitors - Part 1: General - EN 60252-1 2011
Performance, testing and rating - Safety
requirements - Guidance for installation and
operation
- - + A1 2013
IEC 60320 series Appliance couplers for household and similar EN 60320 series
general purposes
IEC 60320-1 - Appliance couplers for household and similar EN 60320-1 2015
general purposes - Part 1: General
———————
1
Dated as no European equivalent exists.
5
---------------------- Page: 8 ----------------------
SIST EN 62841-3-12:2019
EN 62841-3-12:2019 (E)
Publication Year Title EN/HD Year
requirements
IEC 60335-1 (mod) 2010 Household and similar electrical appliances - EN 60335-1 2012
Safety - Part 1: General requirements
- - + A11 2014
- - + AC 2014
- - + A13 2017
IEC 60384-14 - Fixed capacitors for use in electronic EN 60384-14 2013
equipment - Part 14: Sectional specification -
Fixed capacitors for electromagnetic
interference suppression and connection to
the supply mains
- - + A1 2016
1
IEC 60417 1973 Graphical symbols for use on equipment. - -
Index, survey and compilation of the single
sheets.
IEC 60529 1989 Degrees of protection provided by enclosures EN 60529 1991
(IP Code)
- - + corrigendum May 1993
+ A1 1999 + A1 2000
+ A2 2013 + A2 2013
IEC 60664-1 - Insulation coordination for equipment within EN 60664-1 2007
low-voltage systems - Part 1: Principles,
requirements and tests
IEC 60695-2-11 2000 Fire hazard testing -- Part 2-11: Glowing/hot- - -
wire based test methods - Glow-wire
flammability test method for end-products
IEC 60695-2-13 2010 Fire hazard testing - Part 2-13: Glowing/hot- EN 60695-2-13 2010
wire based test methods - Glow-wire ignition
temperature (GWIT) test method for materials
IEC 60695-10-2 2003 Fire hazard testing -- Part 10-2: Abnormal - -
heat - Ball pressure test
IEC 60695-11-10 2013 Fire hazard testing - Part 11-10: Test flames - EN 60695-11-10 2013
50 W horizontal and vertical flame test
methods
IEC 60730-1 (mod) 2010 Automatic electrical controls for household EN 60730-1 2011
and similar use -- Part 1: General
requirements
2
IEC 60825-1 2007 Safety of laser products -- Part 1: Equipment EN 60825-1 2007
classification and requirements
IEC 60884 series Plugs and socket-outlets for household and - -
similar purposes
1
IEC 60906-1 2009 IEC system of plugs and socket-outlets for - -
household and similar purposes - Part 1:
Plugs and socket-outlets 16 A 250 V a.c.
———————
2
This standard has been withdrawn and replaced by EN 60825-1:2014.
6
---------------------- Page: 9 ----------------------
SIST EN 62841-3-12:2019
EN 62841-3-12:2019 (E)
Publication Year Title EN/HD Year
IEC 60947-5-1 - Low-voltage switchgear and controlgear - Part EN 60947-5-1 2017
5-1: Control circuit devices and switching
elements - Electromechanical control circuit
devices
IEC 60990 1999 Methods of measurement of touch current EN 60990 1999
and protective conductor current
IEC 60998-2-1 (mod) - Connecting devices for low-voltage circuits for EN 60998-2-1 2004
household and similar purposes - Part 2-1:
Particular requirements for connecting
devices as separate entities with screw-type
clamping units
IEC 60998-2-2 (mod) - Connecting devices for low-voltage circuits for EN 60998-2-2 2004
household and similar purposes - Part 2-2:
Particular requirements for connecting
devices as separate entities with screwless-
type clamping units
IEC 60999-1 1999 Connecting devices - Electrical copper EN 60999-1 2000
conductors - Safety requirements for screw-
type and screwless-type clamping units - Part
1: General requirements and particular
requirements for clamping units for
conductors from 0,2 mm2 up to 35 mm2
(included)
IEC 61000-4-2 2008 Electromagnetic compatibility (EMC) - Part 4- EN 61000-4-2 2009
2: Testing and measurement techniques -
Electrostatic discharge immunity test
IEC 61000-4-3 2006 Electromagnetic compatibility (EMC) - Part 4- EN 61000-4-3 2006
3 : Testing and measurement techniques -
Radiated, radio-frequency, electromagnetic
field immunity test
+ A1 2007 + A1 2008
+ A2 2010 + A2 2010
IEC 61000-4-4 2012 Electromagnetic compatibility (EMC) - Part 4- EN 61000-4-4 2012
4: Testing and measurement techniques -
Electrical fast transient/burst immunity test
IEC 61000-4-5 2005 Electromagnetic compatibility (EMC) -- Part 4-- -
5: Testing and measurement techniques -
Surge immunity test
IEC 61000-4-6 2008 Electromagnetic compatibility (EMC) -- Part 4-- -
6: Testing and measurement techniques -
Immunity to conducted disturbances, induced
by radio-frequency fields
IEC 61000-4-11 2004 Electromagnetic compatibility (EMC) - Part 4- EN 61000-4-11 2004
11: Testing and measurement techniques -
Voltage dips, short interruptions and voltage
variations immunity tests
IEC 61032 1997 Protection of persons and equipment by EN 61032 1998
enclosures - Probes for verification
1
IEC 61056-1 1991 Portable lead-acid cells and batteries (Valve- - -
regulated types) -- Part 1: General
requirements, functional characteristics -
7
---------------------- Page: 10 ----------------------
SIST EN 62841-3-12:2019
EN 62841-3-12:2019 (E)
Publication Year Title EN/HD Year
Methods of test
IEC 61058-1 2000 Switches for appliances -- Part 1: General - -
requirements
+ A1 2001 EN 61058-1 2002
+ A2 2007 + A2 2008
IEC 61210 (mod) - Connecting devices - Flat quick-connect EN 61210 2010
terminations for electrical copper conductors -
Safety requirements
IEC 61540 (mod) 1997 Electrical accessories - Portable residual HD 639 S1 2002
current devices without integral overcurrent
protection for household and similar use
(PRCDs)
+ A1 1998 - -
- - + A1 2003
- - + corrigendum Jul. 2003
- - + A2 2010
IEC 61558-1 - Safety of power transformers, power supplies, EN 61558-1 2019
reactors and similar products – Part 1:
General requirements and tests
IEC 61558-2-4 - Safety of transformers, reactors, power EN 61558-2-4 2009
supply units and similar products for supply
voltages up to 1 100 V - Part 2-4: Particular
requirements and tests for isolating
transformers and power supply units
incorporating isolating transformers
IEC 61558-2-6 - Safety of transformers, reactors, power EN 61558-2-6 2009
supply units and similar products for supply
voltages up to 1 100 V - Part 2-6: Particular
requirements and tests for safety isolating
transformers and power supply units
incorporating safety isolating transformers
IEC 61558-2-16 - Safety of transformers, reactors, power EN 61558-2-16 2009
supply units and similar products for supply
voltages up to 1 100 V - Part 2-16: Particular
requirements and tests for switch mode
power supply units and transformers for
switch mode power supply units
- - + A1 2013
IEC 61951-1 - Secondary cells and batteries containing EN 61951-1 2017
alkaline or other non-acid electrolytes -
Secondary sealed cells and batteries for
portable applications - Part 1: Nickel-
Cadmium
IEC 61951-2 - Secondary cells and batteries containing EN 61951-2 2017
alkaline or other non acid electrolytes -
Secondary sealed cells and batteries for
portable applications - Part 2: Nickel-metal
hydride
IEC 61960 - Secondary cells and batteries containing EN 61960 2011
alkaline or other non-acid electrolytes -
8
---------------------- Page: 11 ----------------------
SIST EN 62841-3-12:2019
EN 62841-3-12:2019 (E)
Publication Year Title EN/HD Year
Secondary lithium cells and batteries for
portable applications
IEC 61984 - Connectors - Safety requirements and tests EN 61984 2009
IEC 62133 - Secondary cells and batteries containing EN 62133 2013
alkaline or other non-acid electrolytes - Safety
requirements for portable sealed secondary
cells, and for batteries made from them, for
use in portable applications
IEC 62233 (mod) - Measurement methods for electromagnetic EN 62233 2008
fields of household appliances and similar
apparatus with regard to human exposure
- - + corrigendum Aug. 2008
IEC 62471 (mod) - Photobiological safety of lamps and lamp EN 62471 2008
systems
IEC/TR 62471-2 2009 Photobiological safety of lamps and lamp - -
systems - Part 2: Guidance on manufacturing
requirements relating to non-laser optical
radiation safety
ISO 7-1 1994 Pipe threads where pressure-tight joints are - -
made on the threads – Part 1: Dimensions,
tolerances and designation
ISO 1463 - Metallic and oxide coatings -- Measurement EN ISO 1463 2004
of coating thickness -- Microscopical method
ISO 2178 - Non-magnetic coatings on magnetic EN ISO 2178 2016
substrates – Measurement of coating
thickness – Magnetic method
ISO 2768-1 - General tolerances -- Part 1: Tolerances for EN 22768-1 1993
linear and angular dimensions without
individual tolerance indications
ISO 3744 - Acoustics - Determination of sound power EN ISO 3744 2010
levels and sound energy levels of noise
sources using sound pressure - Engineering
methods for an essentially free field over a
reflecting plane
1
ISO 3864-2 2016 Graphical symbols - Safety colours and safety - -
signs – Part 2: Design principles for product
safety labels
1
ISO 3864-3 2012 Graphical symbols - Safety colours and safety - -
signs - Part 3: Design principles for graphical
symbols for use in safety signs
ISO 4871 1996 Acoustics - Declaration and verification of EN ISO 4871 2009
noise emission values of machinery and
equipment
ISO 5347 series Methods for the calibration of vibration and - -
shock pick-ups
ISO 5349-1 - Mechanical vibration - Measurement and EN ISO 5349-1 2001
evaluation of human exposure to hand-
transmitted vibration – Part 1: General
requirements
ISO 5349-2 - Mechanical vibration - Measurement and EN ISO 5349-2 2001
9
---------------------- Page: 12 ----------------------
SIST EN 62841-3-12:2019
EN 62841-3-12:2019 (E)
Publication Year Title EN/HD Year
evaluation of human exposure to hand-
transmitted vibration – Part 2: Practical
guidance for measurement in the workplace
- - + A1 2015
ISO 7000 2012 Graphical symbols for use on equipment - - -
Registered symbols
ISO 7010 - Graphical symbols - Safety colours and safety EN ISO 7010 2012
signs - Registered safety signs
- - + A1 2014
- - + A2 2014
- - + A3 2014
- - + A4 2014
- - + A5 2015
- - + A6 2016
- - + A7 2017
ISO 7574-4 - Acoustics - Statistical methods for EN 27574-4 1988
determining and verifying stated noise
emission values of machinery and equipment
-- Part 4: Methods for stated values for
batches of machines
1
ISO 8041 2005 Human response to vibration - Measuring - -
instrumentation
ISO 9772 2012 Cellular plastics -- Determination of horizontal - -
burning characteristics of small specimens
subjected to a small flame
ISO 11201 - Acoustics - Noise emitted by machinery and EN ISO 11201 2010
equipment - Determination of emission sound
pressure levels at a work station and at other
specified positions in an essentially free field
over a reflecting plane with negligible
environmental corrections
ISO 11203 - Acoustics - Noise emitted by machinery and EN ISO 11203 2009
equipment - Determination of emission sound
pressure levels at a work station and at other
specified positions from the sound power
level
ISO 12100 - Safety of machinery - General principles for EN ISO 12100 2010
design - Risk assessment and risk reduction
ISO 13849-1 - Safety of machinery - Safety-related parts of EN ISO 13849-1 2015
control systems - Part 1: General principles
for design
ISO 13850 - Safety of machinery - Emergency stop EN ISO 13850 2015
function - Principles for design
ISO/TR 11690-3 - Acoustics - Recommended practice for the EN ISO 11690-3 1998
design of low noise workplaces containing
machinery -- Part 3: Sound propagation and
noise prediction in workrooms
10
---------------------- Page: 13 ----------------------
SIST EN 62841-3-12:2019
EN 62841-3-12:2019 (E)
Publication Year Title EN/HD Year
1
ISO 16063-1 1998 Methods for the calibration of vibration and - -
shock transducers – Part 1: Basic concepts
Mechanical vibration – Declaration and EN 12096 1997
verification of vibration emission values
ANSI/ASME 2006 Pipe threads, 60 deg., general purpose - -
B1.20.2M
ASTM B 258 2014 Standard Specification for Standard Nominal - -
Diameters and Cross-Sectional Areas of
AWG Sizes of Solid Round Wires Used as
Electrical Conductors
- - Hand-arm vibration - Guidelines for vibration CR 1030-1 1995
hazards reduction -- Part 1: Engineering
methods by design of machinery
UL 969 2017 Standard for marking and labeling systems - -
11
---------------------- Page: 14 ----------------------
SIST EN 62841-3-12:2019
EN 62841-3-12:2019 (E)
Annex ZZ
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC [2006 OJ L157] aimed to be
covered
This European Standard has been prepared under a Commission’s standardisation request M/396 to provide
one voluntary means of conforming to essential requirements of Directive 2006/42/EC of the European
Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC.
Once this standard is cited in the Official Journal of the European Union under that Directive, compliance
with the normative clauses of this standard given in Table ZZ.1 confers, within the limits of the scope of this
standard, a presumption of conformity with the corresponding essential requirements of that Directive, and
associated EFTA regulations.
Table ZZ.1 – Correspondence between this European Standard
and Annex I of Directive 2006/42/EC
Essential Requirements of Clause(s) / sub-clause(s) Remarks / Notes:
Directive 2006/42/EC of this EN
Clause numbers of Annex I
1.1.2 4
(Principles of safety integration)
1.1.3 5, 6.1, 21.6, K/L.5, L.21
(Materials and products)
1.1.5 19.4
(Design of machinery to facilitate its
handling)
1.1.6 5, 19.5, 21.18.2, K/L.5, L.21
(Ergonomics)
1.2.1 5, 18.6, 18.8, 23.1.6, 23.1.10,
(Safety and reliability of control 23.1.11, 23.3, K/L.5, K/L.18.6,
systems) K/L.18.8, K/L.23.1.10, K.23.1.201,
L.18
1.2.2 5, 8.5, 8.9, 8.10, 8.11, 21.1, 21.2.,
(Control devices) 21.4, 21.17, 21.18, K/L.5,
K.21.17.1.2, L.21
1.2.3 5, 21.17, K/L.5, L.21
(Starting)
1.2.4.1 5, 21.17, K/L.5, L.21
(Normal stop)
1.2.6 5, 21.18.2.1, 23.3, K/L.5, L.21
(Failure of the power supply)
1.3.1 5, 19.7, 19.8, K/L.5
(Risk of loss of stability)
12
---------------------- Page: 15 ----------------------
SIST EN 62841-3-12:2019
EN 62841-3-12:2019 (E)
Essential Requirements of Clause(s) / sub-clause(s) Remarks / Notes:
Directive 2006/42/EC of this EN
Clause numbers of Annex I
1.3.2 5, 8.14.2 c), 13.1, 14.4, 17, 20,
(Risk of break-up during operation) 21.23, 24.11, 24.12, 24.13, 27,
K/L.5, K/L.13.1, K/L.17, K/L.20,
K/L.24.201, K.27.1, L.21
1.3.3 5, 18.3, K/L.5, L.18
(Risk due to falling or ejected objects)
1.3.4 19.2, 21.24, L.21
(Risks due to surfaces, edges or
angles)
1.3.7 5, 19.1, 19.3, 19.101, K/L.5
(Risks related to moving parts)
1.3.8.1 5, 19.1, 19.3, K/L.5
(Moving transmission parts)
1.3.8.2 5, 19.1, K/L.5
(Moving parts involved in the process)
1.4.1 5, 19.1, 20.1, 20.2, 20.3, 20.4,
(General requirements (for guards and 21.22, K/L.5, K.20.1, K.20.3, L.20,
protective devices)) L.21
1.4.2.1 5, 19.1, 19.9, K/L.5
(Special requirements for fixed guards)
1.4.2.3 5, 19.1, K/L.5
(Special requirements for adjustable
guards restricting access)
1.5.1 5, 7, L.7.1, 9, 10, 11, 12, 14, 15, 16,
(Risks due to electricity supply) 17, 18.1 - 18.7, 20.5, 21.3, 21.5 -
21.16, 21.19 - 21.22, 21.25 - 21.34,
22, 23.1.1 - 23.1.5, 23.1.7 - 23.1.9,
23.2, 23.4, 23.5, 24, 25, 26, 27, 28,
K/L.5, K.7, K/L.9, K/L.10, K/L.11,
K/L.12, K/L.14, K/L.16, K/L.17,
K.18.1 – K.18.7, K.21.5 -K.21.16,
K.21.19 – K.21.22, K.21.25 –
K.21.34, K/L.22, K/L.24, K/L.25,
K/L.26, K.27.1, K/L.28.1, K.28.2,
L.18, L.18.201, L.20, L.21, Annex C
1.5.4 5, 8.7, 8.8, 8.13, 8.14.2, 21.7, 21.8,
(Risks due to errors of fitting) 21.19, 27.1, K/L.5, K.8.7, K.8.8,
K/L.19.201, K/L.21.201, K/L.21.203,
K.27.1, L.21
1.5.5 5, 12.5, K/L.5, K.12.1
(Risks due to extreme temperatures)
1.5.6 5, 13, 18.1, 18.2, 18.4, 18.6, 28.1,
(Risks due to fire) K/L.5, K/L.12.201, K/L.13, K.18.1,
K.18.6, K/L.18.201, K/L.18.202,
K/L.18.203, K.20.1, K.20.3,
K/L.21.201, K/L.21.203, K/L.23.201,
K/L.23.202, K/L.28.1, L.18,
L.18.204, L.20.201, L.20.202,
L.28.201
13
---------------------- Page: 16 ----------------------
SIST EN 62841-3-12:2019
EN 62841-3-12:2019 (E)
Essential Requirements of Clause(s) / sub-clause(s) Remarks / Notes:
Directive 2006/42/EC of this EN
Clause numbers of Annex I
1.5.7 5, K/L.5, K/L.12.201, K.18.201,
(Risks due to explosion) K/L.18.202, K/L.18.203, K/L.19.202,
K.20.1, K.20.3, K/L.21.202,
K/L.21.203, L.18.204, L.20.201,
L.20.202
1.5.8 I.2.Z1
(Risks due to noise)
1.5.10 5, 6.1, 6.3, K/L.5
(Risks due to radiation)
1.5.11 5, 18.8, K/L.5, K/L.18.8
(Risks due to external radiation)
1.5.12 6.2
(Risks due to laser radiation)
1.6.1 24.1
(Machinery maintenance)
1.6.2 21.17
(Access to operating positions and
servicing points)
1.6.3 24.1
(Isolation of energy sources)
1.7.1 8.1, 8.2, 8.4, 8.6, K/L.8.1, K/L.8.4
(Information and warnings on
machinery)
1.7.2 8.2
(Warning of residual risks)
1.7.3 8.3, 8.4, 8.12, K/L.8.3, K/L.8.4
(Marking of machinery)
1.7.4 8.14, K/L.8.14.1.1, K/L.8.14.2
(Instructions)
WARNING 1: Presumption of conformity stays valid only as long as a reference to this European standard is
maintained in the list published in the Official Journal of the European Union. Users of this standard should
consult frequently the latest list published in the Official Journal of the European Union.
WARNING 2: Other Union legislation may be applicable to the product(s) falling within the scope of this
standard."
14
---------------------- Page: 17 ----------------------
SIST EN 62841-3-12:2019
---------------------- Page: 18 ----------------------
SIST EN 62841-3-12:2019
IEC 62841-3-12
®
Edition 1.0 2017-08
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electric motor-operated hand-held tools, transportable tools and lawn and
garden machinery – Safety –
Part 3-12: Particular requirements for transportable threading machines
Outils électroportatifs à moteur, outils portables et machines pour jardins et
pelouses – Sécurité –
Partie 3-12: Exigences particulières relatives aux machines à fileter portables
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 25.140.20 ISBN 978-2-8322-4753-2
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 19 ----------------------
SIST EN 62841-3-12:2019
– 2 – IEC 62841-3-12:2017 © IEC 2017
CONTENTS
FOREWORD . 3
1 Scope .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.