SIST EN 15767-1:2026

SLOVENSKI STANDARD
oSIST prEN 15767-1:2025
01-september-2025
Prenosna oprema za črpanje in uporabo gasilnega sredstva in podporne gasilske
operacije - Prenosni monitorji - 1. del: Splošne zahteve za prenosne monitorje
Portable equipment for projecting extinguishing agents and firefighting support
operations - Portable monitors - Part 1 : General requirements for portable monitor
assemblies
Tragbare Geräte zum Ausbringen von Löschmitteln und zur Unterstützung der
Brandbekämpfung -Tragbare Wasserwerfer - Teil 1: Allgemeine Anforderungen für
tragbare Wasserwerfer
Equipement portable pour la projection d'agents d'extinction et les opérations de soutien
à la lutte contre les incendies – Lances--canon portables – Partie 1: Exigences
générales pour les ensembles lances--canon portables
Ta slovenski standard je istoveten z: prEN 15767-1
ICS:
13.220.10 Gašenje požara Fire-fighting
oSIST prEN 15767-1:2025 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

oSIST prEN 15767-1:2025
oSIST prEN 15767-1:2025
DRAFT
EUROPEAN STANDARD
prEN 15767-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2025
ICS 13.220.10 Will supersede EN 15767-1:2009
English Version
Portable equipment for projecting extinguishing agents
and firefighting support operations - Portable monitors -
Part 1 : General requirements for portable monitor
assemblies
Equipement portable pour la projection d'agents Tragbare Geräte zum Ausbringen von Löschmitteln
d'extinction et les opérations de soutien à la lutte und zur Unterstützung der Brandbekämpfung -
contre les incendies - Lances--canon portables - Partie Tragbare Wasserwerfer - Teil 1: Allgemeine
1: Exigences générales pour les ensembles lances-- Anforderungen für tragbare Wasserwerfer
canon portables
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 192.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15767-1:2025 E
worldwide for CEN national Members.

oSIST prEN 15767-1:2025
prEN 15767-1:2025 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Description . 6
5 Requirements and verification . 7
5.1 General . 7
5.2 Mechanical characteristics . 7
5.2.1 Fitting systems . 7
5.2.2 Mass . 8
5.2.3 Operating and handling elements . 8
5.3 Materials . 9
5.4 Hydraulic characteristics . 9
5.4.1 General . 9
5.4.2 Pressure loss . 10
5.4.3 Sensitivity to heat . 10
5.4.4 Sensitivity to frost . 10
5.4.5 Burst pressure resistance for portable monitor body without pressure
limiting device . 10
5.4.6 Burst pressure resistance for portable monitor body equipped with a
pressure limiting device . 10
5.4.7 Leak-tightness . 11
5.5 Stability . 11
6 Information for use . 11
6.1 Instruction and maintenance handbook . 11
6.1.1 General . 11
6.1.2 Instruction handbook . 11
6.1.3 Maintenance handbook . 12
6.2 Marking . 12
Annex A (informative) Acceptance test on delivery . 13
Annex B (normative) Datasheet for monitors . 14
Annex C (informative) Example of completed datasheet for monitors . 16

oSIST prEN 15767-1:2025
prEN 15767-1:2025 (E)
European foreword
This document (prEN 15767-1:2025) has been prepared by Technical Committee CEN/TC 192 “Fire
service equipment”, the secretariat of which is held by BSI.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 15767-1:2009.
prEN 15767-1:2025 includes the following significant changes with respect to EN 15767-1:2009:
— the title has been amended;
— definition 3.9: the term has been changed to “maximum stated flowrate”;
— according to current rules for drafting standard, notes containing the word “should” have been
transformed into normative text;
— Clause 4: new title “Description” and the list of components has been updated;
— each verification has been placed under the corresponding requirement (see Clause 5);
— all general requirements have been placed in a new 5.1 “General”
— requirements regarding the mass have been updated (see 5.2.2);
— requirements and corresponding verification for sensitivity to heat have been added (see 5.4.3);
— addition of the missing requirement in 5.4.4, 5.4.5, 5.4.6 and 5.4.7;
— addition of the missing verification in 5.2.3 and 5.3;
— 5.5 (stability): the note has been changed to a warning and placed at the beginning of the verification;
— the instruction handbook has been completed (see 6.1.2);
— improvement of the wording/editorial changes.
oSIST prEN 15767-1:2025
prEN 15767-1:2025 (E)
Introduction
This document has been created to provide a minimum level of safety and performance criteria.
Its purpose is not to define a specific monitor design but to help the user in understanding and choosing
the correct equipment.
The manufacturer may be defined as the person or company taking technical responsibility for the supply
of the product.
oSIST prEN 15767-1:2025
prEN 15767-1:2025 (E)
1 Scope
This document specifies safety requirements, performance requirements, test methods, instructions for
use and maintenance, and marking requirements for portable monitor assemblies.
NOTE 1 Additional requirements for water nozzles and foam devices can be found in EN 15767-2 and
EN 15767-3 respectively.
NOTE 2 Fitting systems are dealt with in national standards or requirements, respectively.
This document is applicable to portable monitor assemblies that can be both permanently installed (e.g.
on a flange, a vehicle, a fire boat, etc.) and can also be used as portable monitor assemblies.
This document can be read in conjunction with either part 2 or 3.
This document is not applicable to monitors permanently installed on firefighting and rescue service
[2]
vehicles, for which requirements are given in EN 1846-3 .
This document is not applicable to portable monitor assemblies which are manufactured before its date
of publication.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
1)
EN 15767-2, , Portable equipment for projecting extinguishing agents and firefighting support
operations — Portable monitors — Part 2: Water nozzles
1)
EN 15767-3 , Portable equipment for projecting extinguishing agents and firefighting support operations
— Portable monitors — Part 3: Foam devices
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/
— IEC Electropedia: available at https://www.electropedia.org/
3.1
portable monitor assembly
combination of components for ground operations that connects to a water supply via hose(s) and
coupling(s) and projects extinguishing agents according to the operator’s requirements
3.2
portable monitor body
portable monitor assembly without nozzle

Under revision.
oSIST prEN 15767-1:2025
prEN 15767-1:2025 (E)
3.3
nozzle
component connected to the outlet of the monitor body that controls the water or the foam flowrate
and/or pattern
Note 1 to entry Water nozzles are defined in EN 15767-2 and foam devices are defined in EN 15767-3.
Note 2 to entry 1 bar = 0,1 Mpa (10 Pa).
3.4
reference pressure
p
R
standard working pressure used to run hydraulic tests and dynamic leakage tests
2)
Note 1 to entry The pressures are expressed in bar .
3.5
nominal pressure
p
N
maximum working pressure
3.6
test pressure
p
t
pressure used for static leakage tests
3.7
burst pressure
p
B
static pressure used for burst test
3.8
pressure loss
Δ
p
difference between the inlet and the outlet pressure of the portable monitor body for a given flow
3.9
maximum stated flowrate
Q
max
flow under which the portable monitor assembly can be operated safely and efficiently
4 Description
A portable monitor assembly shall comprise at least the following components (see Figure 1):
a) a portable monitor body:
1) a fitting system (1). Where the fitting system has more than one connection or inlet they shall be
arranged in a way that no extinguishing agent can unintentionally exit any inlet (e.g. by the use
of a non return valve);
2) a ground base (2);
2 5
1 bar = 0,1 Mpa (10 Pa).
oSIST p
...