SIST EN 15227:2020

SLOVENSKI STANDARD
01-junij-2020
Nadomešča:
SIST EN 15227:2008+A1:2010
Železniške naprave - Zahteve za zagotavljanje varnosti železniških vozil pri trčenju
Railway applications - Crashworthiness requirements for rail vehicles
Bahnanwendungen - Anforderungen für die Kollisionssicherheit von Schienenfahrzeugen
Applications ferroviaires - Exigences de sécurité contre collision pour véhicules
ferroviaires
Ta slovenski standard je istoveten z: EN 15227:2020
ICS:
45.060.01 Železniška vozila na splošno Railway rolling stock in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 15227
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2020
EUROPÄISCHE NORM
ICS 45.060.01 Supersedes EN 15227:2008+A1:2010
English Version
Railway applications - Crashworthiness requirements for
rail vehicles
Applications ferroviaires - Exigences de sécurité contre Bahnanwendungen - Anforderungen für die
collision pour véhicules ferroviaires Kollisionssicherheit von Schienenfahrzeugen
This European Standard was approved by CEN on 10 February 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15227:2020 E
worldwide for CEN national Members.

Contents Page
European foreword . 5
Introduction . 7
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 8
4 Crashworthiness design of rail vehicle structures . 10
4.1 General principles . 10
4.2 Crashworthiness design objectives . 11
4.3 Rail vehicle crashworthiness assessment process . 11
5 Crashworthiness assessment requirements . 11
5.1 Crashworthiness design categories of rail vehicles . 11
5.2 Train assessment methods . 12
5.2.1 Complete train set method . 12
5.2.2 Reference train method . 13
5.2.3 Summary of train assessment methods . 13
5.3 Design collision scenarios . 13
5.4 Assessment of design collision scenarios . 14
5.4.1 General . 14
5.4.2 Design collision scenario for category C-I . 15
5.4.3 Design collision scenario for category C-II . 15
5.4.4 Design collision scenario for category C-III . 15
5.4.5 Design collision scenario for category C-IV . 16
5.4.6 Summary of design collision scenarios . 16
6 Structural passive safety design requirements . 18
6.1 Assessment requirements for design collision scenarios . 18
6.1.1 General . 18
6.1.2 Explanatory notes (informative) . 18
6.2 Overriding . 19
6.2.1 Requirements . 19
6.2.2 Explanatory notes (informative) . 19
6.3 Survival space, intrusion and egress . 20
6.3.1 General requirements . 20
6.3.2 Survival space requirements for passenger areas . 20
6.3.3 Driver’s cab survival space requirements. 21
6.3.4 Explanatory notes (informative) . 21
6.3.5 Definition of driver’s seat survival space envelopes . 22
6.4 Deceleration limit/collision pulse . 25
6.4.1 Requirement . 25
6.4.2 Explanatory notes (informative) . 26
6.5 Obstacle deflector . 26
6.5.1 Requirement . 26
6.5.2 Explanatory notes (informative) . 29
6.6 Lifeguards . 30
6.6.1 Requirement . 30
6.6.2 Explanatory notes (informative) . 30
7 Validation of crashworthiness . 30
7.1 Validation programme . 30
7.2 Combined validation programme . 31
7.2.1 Step 1: Test of energy absorbing devices and crumple zones . 31
7.2.2 Step 2: Test Calibration of the numerical model . 31
7.2.3 Step 3: Numerical simulation of the design collision scenarios . 31
7.3 Reduced validation programme . 32
7.4 Conformity assessment . 32
Annex A (informative) Parameters of design collision scenarios . 33
A.1 Introduction . 33
A.2 Determining the design collision scenarios for collision risks which differ from the
normal European operations . 34
A.2.1 Design collision scenarios . 34
A.2.2 Risk analysis . 34
A.2.3 Factors to be considered in the risk assessment . 35
A.2.4 Collisions following derailment . 35
A.2.5 Bibliography of relevant accident information . 36
Annex B (normative) Requirements of a validation programme . 37
B.1 Test specifications . 37
B.1.1 Test programme . 37
B.1.2 Acceptance criteria for calibration/validation tests . 37
B.2 Numerical simulations . 38
B.2.1 Numerical model validation . 38
B.2.2 Simulation modelling . 38
Annex C (normative) Reference obstacle definitions . 40
C.1 80 t wagon with side buffers . 40
C.2 80 t wagon with heavy duty coupler. 41
C.3 129 t regional train . 43
C.4 Level crossing 15 t deformable obstacle . 44
C.5 Urban road traffic 3 t rigid corner collision obstacle . 46
C.6 Urban road traffic 7,5 t obstacle . 47
Annex D (normative) Reference train definitions . 50
D.1 Reference trains for locomotive, power head, driving trailer and coach design . 50
D.2 Locomotive design . 50
D.3 Power head and driving trailer design . 50
D.4 Coach design . 51
D.5 Coach design limited to specific leading vehicles . 52
Annex E (informative) Migration rule for this European Standard . 54
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2016/797/EU aimed to be covered . 55
Bibliography . 57

European foreword
This document (EN 15227:2020) has been prepared by Technical Committee CEN/TC 256 “Railway
applications”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2020, and conflicting national standards
shall be withdrawn at the latest by October 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 15227:2008+A1:2010.
This document has been prepared under a mandate given to CEN/CENELEC/ETSI by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive 2016/797/EU.
For relationship with EU Directive 2016/797/EU, see informative Annex ZA, which is an integral part
of this document.
Additionally to a general editorial reordering of clauses and text the technical changes with respect to
the previous edition are listed below:
a) applicable vehicle types (1);
b) modified definitions and examples for crashworthiness design categories (5.1);
c) definition of train sets to be assessed (5.2);
d) assessment of train set which is only operated in one direction (5.2);
e) mandatory requirement of initial vertical offset for design collision scenario 1 for all
crashworthiness design categories (5.4.1);
f) new definition of collision mass in accordance with EN 15663 mass definitions (5.4.1);
g) new requirements for locomotives with heavy duty couplers (5.4.2 and C.2);
h) mandatory requirement for locomotives with centre cabs to fulfil design collision scenario 3 (5.4);
i) additional design collision scenario for crashworthiness design category C-IV (5.4.5 and C.6);
j) new requirement for support condition of side windows at vehicle ends (6.3.1);
k) exclusion of gangways from survival space (6.3.2);
l) mandatory requirement that the survival space for the driver shall be inside the cab (6.3.1);
m) modified definition for driver’s seat survival space envelopes (6.3.5);
n) elimination of deceleration limits for design collision scenario 3 (6.4.1);
o) modified deceleration limits and modified deceleration assessment method for design collision
scenarios 1 and 2 (6.4.1);
p) modified requirement for obstacle deflectors with respect to gauge limits (6.5.1);
q) new requirements for lifeguards (6.6);
r) new requirement for tests of structures or components mounted at intermediate ends (B.1.1)
s) modified obstacle geometry for design collision scenario 3 for crashworthiness design category C-
III (C.3);
t) modified reference train for coach design (D.4);
u) new train definition for coach design limited to specific leading vehicles (D.5).
v) alignment of terms and definitions to prEN 17343:2019.
If a vehicle has been successfully assessed using the previous edition of this standard, and the
technical changes of the new edition of EN 15227 do not affect this assessment, the vehicle can be
regarded to conform to the new standard. Otherwise, if the vehicle needs to be reassessed, it is
sufficient to assess only the modified technical requirements and new requirements.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
Introduction
The objective of the passive safety requirements described in this European Standard is to reduce the
consequences of collision accidents. The measures considered in this European Standard provide the
means of protection when all possibilities of preventing an accident have failed. It provides a
framework for determining the crash conditions that rail vehicle bodies can be designed to withstand,
based on the most common collisions and associated risks.
This European Standard adds to the basic strength requirement defined in EN 12663-1:2010+A1:2014
by setting additional requirements for structural passive safety in order to increase occupant safety in
case of collisions.
In the event of a collision, application of this European standard provides protection for the occupants
of new designs of crashworthy vehicles through the preservation of structural integrity, reducing the
risk of overriding and limiting decelerations. This protection does not extend to interactions between
the occupants and the vehicle interior or to occupants of other rail vehicles, to other railway
employees and customers who are not in vehicles, or to third parties.
1 Scope
This document specifies crashworthiness requirements applicable to new designs of:
— locomotives,
— driving vehicles operating in passenger and freight trains;
— passenger rail vehicles operating in passenger trains (such as trams, metros, mainline trains).
This document identifies common methods of providing passive safety that can be adapted to suit
individual vehicle requirements.
This document specifies the characteristics of reference obstacle models for use with the design
collision scenarios.
This document also specifies the requirements and methods for demonstrating that the passive safety
objectives have been achieved by comparison with existing proven designs, numerical simulation,
component or full-size tests, or a combination of all these methods.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
EN 12663-1:2010+A1:2014, Railway applications - Structural requirements of railway vehicle bodies -
Part 1: Locomotives and passenger rolling stock (and alternative method for freight wagons)
EN 15663:2017+A1:2018, Railway applications - Vehicle reference masses
prEN 17343:2019, Railway applications — General terms and definitions
3 Terms and definitions
For the purposes of this document, the terms and definitions given in prEN 17343:2019 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
active safety
systems and measures which take actions that aim to prevent a collision occurring
3.2
collision mass
effective vehicle mass used for collision simulations
3.3
collision speed
ν
C
velocity difference between trains or train and obstacle at the start of the collision
3.4
crashworthiness
ability to mitigate the consequences of a collision in a controlled manner and reduce the risk of injury
to the occupants
3.5
crumple zone
part of the vehicle body (usually at the vehicle ends) which is designed to deform in a controlled
manner and absorb energy
3.6
design collision scenario
collision scenario that is applicable for design and assessment
3.7
energy-absorbing device
device which is attached to the vehicle structure, designed to deform in a controlled manner and
absorb energy
EXAMPLE Energy-absorbing coupler
3.8
full-size test
test where the specimen is made using full-size components from the vehicle being assessed
3.9
heavy duty coupler
centre couplers conforming to the Willison or Janney principles
EXAMPLES SA3 coupler (Willison), AAR coupler (Janney)
Note 1 to entry: AAR: Association of American Railroads
3.10
leading end
end of a vehicle which in normal service can be the front of a train
3.11
level crossing speed
ν
LC
applicable rail vehicle speed at level crossing
3.12
lifeguard
structural element positioned in front of a wheel with the objective of preventing small obstacles from
passing between the wheel and the rail
3.13
normal European operating conditions
operating conditions comparable to those described by the documents listed in the bibliography
3.14
obstacle deflector
device mounted on the leading ends of vehicles to limit the consequences of striking an obstruction on
the track
3.15
passive safety
structural design characteristics intended to reduce the consequences of a collision
3.16
survival space
space to be preserved for passengers and staff inside a rail vehicle for the design collision scenarios
3.17
reference train
train configuration that is used for the assessment and validation of locomotives, power heads, driving
trailers and coaches that do not form part of a train set
4 Crashworthiness design of rail vehicle structures
4.1 General principles
The risk of train collisions is primarily controlled by active safety systems and/or operational
procedures. Where these systems are inadequate due to particular circumstances or due to external
events, structural crashworthiness provides a set of passive safety measures that will reduce the
consequences of an accident.
The objective is to provide a level of protection consistent with the most common collisions and
associated risks through the application of the design collision scenarios specified in this document. It
is not practical to design vehicle structures to protect the occupants against all possible accidents or to
consider all possible vehicle combinations.
Normal European operating conditions are assumed. The design of new vehicles for use in passenger
trains assumes operations with compatible rolling stock that also meet this European standard. It is
recognized that operational requirements may require new crashworthy and existing non-
crashworthy vehicles to exist in the same train but such combinations of vehicles are not required to
comply with this European Standard.
The applicable design collision scenarios, and suitable parameters for normal European operations are
given in 5.3.
Annex A gives additional information regarding the derivation of the design collision scenarios and
describes situations when they may need to be modified and the processes that should then be
followed.
If the operational conditions are such that a design collision scenario cannot occur, or there is evidence
that the probability of it occurring or the associated risk is so low as to be broadly acceptable, there is
no need to consider this design collision scenario in the vehicle design. These conditions should be set
out in the vehicle specification.
NOTE Train control systems which segregate different types of traffic on the same system or modes of
traffic that are segregated by infrastructure (e.g. no level crossings) can satisfy this requirement.
If the system has characteristics that result in significant collision risks that are not addressed by the
design collision scenarios considered in this European standard, they should also be considered in the
form of additional design collision scenarios, which should form part of the vehicle specification.
The requirements apply to the vehicle body, and to those mechanical elements directly associated with
it that may be used to absorb energy in a collision, such as couplers, drawgear and buffing systems.
The requirements do not cover the safety features of doors, windows, system components or interior
features except for specific issues relating to the preservation of survival space.
Not all vehicles in a train have to incorporate energy absorption, provided that passenger train
configurations formed entirely of new vehicle designs comply as a whole with this European Standard.
4.2 Crashworthiness design objectives
To provide protection for the occupants of rail vehicles in the event of a collision, the requirements
take into account the following objectives:
— absorption of collision energy in a controlled manner;
— reduction of the risk of overriding;
— maintenance of survival space and structural integrity of occupied areas;
— limiting deceleration;
— reduction of the risk of derailment and the consequences of hitting a track obstruction.
Specific requirements and assessment criteria to demonstrate that these objectives are satisfied are
set out in Clauses 5, 6 and 7 (see 4.3).
As a by-product of providing occupant protection, the level of damage to the vehicle body is likely to be
reduced in accidents. If more restrictive limits are intended to be placed on damage resulting from any
of the design collision scenarios set out in Clause 5, these should be part of the vehicle specification
and do not form part of the safety requirements set out in this European Standard.
4.3 Rail vehicle crashworthiness assessment process
For a new rail vehicle, the stages of the crashworthiness assessment process shall be:
— allocation of a crashworthiness design category (see 5.1);
— determination of the relevant train assessment methods (see 5.2 and Annex D) and determination
of the applicable design collision scenarios (see 5.3 and 5.4). If non-standard design collision
scenarios are required, see Annex A for guidance on the methods that should be adopted;
— validation of the crashworthiness assessment (see Clause 7 and Annex B).
— assessment of the applicable design collision scenarios with respect to the applicable
crashworthiness design criteria (see 5.4, Clause 6 and Annex C);
5 Crashworthiness assessment requirements
5.1 Crashworthiness design categories of rail vehicles
For the application of this European standard rail vehicles are classified into crashworthiness design
categories. These categories depend on the main characteristics of the rail network infrastructure and
on the type of operation.
The appropriate crashworthiness design category or categories shall be defined in the vehicle
specification.
Rail vehicles are divided into four categories as indicated in Table 1, with an indication of the type of
operation and vehicles generally associated with each.
Table 1 — Crashworthiness design categories of rail vehicles
Category Definition Examples of vehicle types
C-I Vehicles except urban vehicles and trams Locomotives, coaches and trains
designed to operate on international, national
and regional networks
C-II Urban vehicles designed to operate only on a Metro vehicles
dedicated rail network, with no level
crossings and no interface with road traffic
C-III Vehicles designed to operate on urban and/or Tram-trains, peri-urban trams
regional networks, in track-sharing
operation, and interfacing with road traffic
C-IV Trams
5.2 Train assessment methods
5.2.1 Complete train set method
This method is applicable for train sets and railcars.
When assessing a train set with significantly different vehicle structures at each end, collisions at both
ends shall be considered. For impacts between identical train sets only impacts between identical train
set ends shall be considered.
When assessing a train set which is only operated in one direction and which has significantly
different vehicle structures at each end, then head-on collision impacts at the leading ends and rear-on
collisions of a leading end against a non-leading end shall be accounted for.
When assessing a train set which can be assembled and operated in different configurations of a same
architecture, the shortest and longest train set shall be considered, e.g. if a train set can be configured
to a fixed formation of 4 to 8 vehicles, the formation with 4 vehicles and the formation with 8 vehicles
are assessed.
When assessing a train set which can also be operated in a train of two or more train sets, the
assessment of only one single train set is sufficient but when assessing a train set with retractable or
foldable coupler systems which can also be operated in a train of two or more train sets the
assessment of two train sets is necessary.
NOTE The energy absorption devices of coupled train set ends sufficiently decouple the energy required to
be absorbed by each train set in case of collisions. At the leading end of the train with retractable or foldable
coupler systems the coupler is normally retracted or folded away. The behaviour of these couplers at the
intermediate ends during collisions of trains with two or more train sets is demonstrated with the assessment of
two train sets.
When assessing a train set which due to its design is always operated as a train of at least two train
sets, the minimum number of train sets to form a train shall be assessed.
Some train sets may not have a control cab to lead a train at both ends (for example just a control
panel for shunting), but are intended to be always operated as trains in both directions. Therefore the
minimum operational train consist will be the one with a control cab positioned at each end.
5.2.2 Reference train method
This method is applicable for locomotives, power heads, driving trailers and coaches which are used
with a variable formation of vehicles. For such vehicles applicable reference trains shall be used for the
assessment. For applicable reference trains and assessment requirements of different vehicle types
see Annex D.
5.2.3 Summary of train assessment methods
The applicable assessment methods and references to Annex D are indicated in Table 2.
Table 2 — Vehicle types and assessment methods
Vehicle types Assessment method
Train sets and railcars Complete train set method
Locomotives Reference train method (see D.2 for reference train definitions)
Power heads and driving Reference train method (see D.3 for reference train definitions)
trailers
Coaches Reference train method (see D.4 and D.5 for reference train definitions)
5.3 Design collision scenarios
In the following, four design collision scenarios are specified. Annex A discusses the derivation and
application of the design collision scenarios in more detail.
1. Design collision scenario 1): a leading end impact between two identical trains;
The moving train is impacting an identical stationary train. Both the moving and stationary train
have to be assessed.
This scenario is also representative of collisions with similar trains fitted with compatible
coupling arrangements.
2. Design collision scenario 2): a leading end impact with a different type of rail vehicle;
Depending on the crashworthiness design category the train to be assessed is colliding with a
regional train equipped with a central coupler or a wagon.
This scenario is representative of collisions with other rolling stock or with buffer stops.
If the type of rolling stock typically encountered differs from the defined reference obstacles, then
Annex A should be used to define more appropriate obstacles.
3. Design collision scenario 3): a leading end impact with a road vehicle;
The train to be assessed is colliding with a large obstacle at level crossings or, where appropriate,
with common urban road traffic obstacles.
This scenario is representative of collisions with large road vehicles.
4. Design collision scenario 4): a leading end impact with a low obstacle.
Obstacle deflectors and lifeguards of the train to be assessed shall fulfil specified strength and
performance criteria.
This scenario is representative of collisions with obstacles having their centre of mass below the
train head stock (e.g. a car on a level crossing, animals or debris).
If vehicles cannot operate up to the collision speeds specified in this European Standard (e.g. shunting
locomotives) the crashworthiness requirements need not be applied.
If the normal European operating conditions assumed by this European Standard do not apply,
appropriate scenarios and limiting design cases shall be defined in the vehicle specification. See
Annex A for guidance on defining suitable requirements.
Table 3 summarizes these design collision scenarios with respect to the different crashworthiness
design categories. The relevant obstacles, relevant operational characteristics and collision speeds are
given.
Tables 6 and 7 set out the performance requirements for obstacle deflectors and lifeguards.
5.4 Assessment of design collision scenarios
5.4.1 General
For all crashworthiness design categories and all vehicle types the following requirements apply.
The design collision scenarios shall be assessed using any combination of:
— numerical simulations,
— calculations and
— physical testing.
Colliding trains, stationary trains and obstacles are un-braked on straight and level track. The
impacted collision obstacle (train, wagon or obstacle) is stationary. Boundary conditions for impacted
wagons and obstacles are included in their definition (See Annex C).
For design collision scenario 1, for all crashworthiness design categories, the initial vertical offset at
the point of contact shall be 40 mm, with the stationary train at a lower level than the moving train.
There is no initial vertical offset at intermediate ends in each train.
Front coupler systems can be considered to be interlocked during design collision scenario 1
independent of their vertical gathering range.
The collision mass is the design mass in working order in accordance with EN 15663:2017+A1:2018
plus 50 % of the mass of seated passengers. The masses of staff and seated passengers do not need to
be represented at their centres of gravity but may be directly included in the vehicle structure mass.
The applicable design collision scenarios and corresponding requirements for the crashworthiness
design categories C-I to C-IV are set out in 5.4.2 to 5.4.5 and finally summarized in 5.4.6, Table 3.
5.4.2 Design collision scenario for category C-I
All crashworthiness design category C-I vehicle types except coaches shall be assessed for the
following:
a) design collision scenario 1 at a collision speed of 36 km/h
For locomotives fitted with heavy duty couplers, the design collision scenario 1 shall be assessed
at a collision speed of 20 km/h
b) design collision scenario 2, an impact against an 80 t freight wagon fitted with side buffers at a
collision speed of 36 km/h. The reference obstacle is defined in C.1.
For locomotives fitted with heavy duty couplers, the design collision scenario 2 shall be assessed
for an impact against an 80 t freight wagon fitted with a centre coupling at a collision speed of
20 km/h. The reference obstacle is defined in C.2.
c) design collision scenario 3; a collision at the leading end against a level crossing 15 t deformable
obstacle. The reference obstacle is defined in C.4. The level crossing collision speed shall be the
lesser of (ν – 50 km/h) or 110 km/h, where the level crossing speed ν is the lower of
LC LC
• the maximum train speed and
• the designated line speed at level crossings
Unless otherwise required, an assessment against design collision scenario 3 is only necessary if
there are level crossings on the routes to be operated.
d) design collision scenario 4; leading end impact with a low obstacle. Vehicle leading ends shall fulfil
the performance requirements for obstacle deflectors and lifeguards as given in 6.5 and 6.6.
Crashworthiness design category C-I coaches shall be assessed according to the requirements given in
D.4 or D.5. This is equivalent to design collision scenario 1 for these vehicles. The other design collision
scenarios are not applicable for coaches.
5.4.3 Design collision scenario for category C-II
Crashworthiness design category C-II vehicles shall be assessed for design collision scenario 1 with a
collision speed of 25 km/h.
NOTE The other design collision scenarios are not applicable to crashworthiness design category C-II.
5.4.4 Design collision scenario for category C-III
Crashworthiness design category C-III vehicles shall be assessed for the following
a) design collision scenario 1 with a collision speed of 25 km/h
b) design collision scenario 2, for collisions with a different type of rail vehicles:
• for service conditions where track is shared with vehicles equipped with side buffers, an
impact against an 80 t wagon with a collision speed of 25 km/h. The reference obstacle is
defined in C.1.
• for service conditions where track is shared with vehicles equipped with a central coupler, an
impact against a 129 t regional train with a collision speed of 10 km/h. The reference obstacle
is defined in C.3.
The types of rail vehicle used as reference obstacles are suitable for normal European operating
conditions. If the type of rolling stock typically encountered differs from the defined reference
obstacles, then Annex A should be used to define more appropriate obstacles.
c) design collision scenario 3; at leading ends for operations with level crossings, an impact against a
level crossing 15 t deformable obstacle with a collision speed of 25 km/h. The reference obstacle
is defined in C.4.
d) design collision scenario 4; vehicle leading ends shall fulfil the performance requirements for
obstacle deflectors and lifeguards as given in 6.5 and 6.6.
The requirements for category C-III provide sufficient safety for a tram network operation, i.e. the
requirements of category C-IV need not be demonstrated separately.
5.4.5 Design collision scenario for category C-IV
Crashworthiness design category C-IV vehicles shall be assessed for the following:
a) design collision scenario 1 with a collision speed of 15 km/h
b) design collision scenario 3, which shall be assessed at leading ends for the following cases:
• An impact against a 3 t rigid road traffic obstacle positioned at 45 degrees to the track with a
collision speed of 25 km/h. The reference obstacle and the design collision scenario are
described in C.5.
• Impacts against a 7,5 t road traffic obstacle positioned at 90 degrees to the track and a lateral
offset of the centre of gravity of the obstacle relative to x- axis of train of ± 1000 mm with a
collision speed of 15 km/h. The reference obstacle and the design collision scenarios are
described in C.6.
5.4.6 Summary of design collision scenarios
The design collision scenarios set out in 5.4.2 to 5.4.5 are summarized in Table 3.

Table 3 — Design collision scenarios and collision obstacles
Design collision scenario (see 5.3) and collision speeds v
C
1 2 3 4
Crashworthiness design
categories
leading end
leading end
impact between leading end impact with a
(see 5.1)
leading end impact with a large road vehicle impact with a
two identical different type of rail vehicle
low obstacle
trains
Crashworthiness Detailed Identical train 80 t freight 129 t 15 t deformable 7,5 t 3 t rigid Obstacle
design category requirements wagon regional obstacle obstacle obstacle deflectors and
(see Table 1) train lifeguards
(see C.1 and (see C.4) (see C.6) (see C.5)
C.2) (see C.3)
See 6.5 and 6.6
= (ν - 50 km/h)
LC
a a
C-I 5.4.2 36 km/h 36 km/h n/a n/a n/a for
≤ 110 km/h
requirements
C-II 5.4.3 25 km/h n/a n/a n/a n/a n/a n/a
See 6.5 and 6.6
C-III 5.4.4 25 km/h 25 km/h 10 km/h 25 km/h n/a n/a for
requirements
C-IV 5.4.5 15 km/h n/a n/a n/a 15 km/h 25 km/h n/a
NOTE: n/a = not applicable
a
for C-I locomotives fitted with heavy duty couplers the collision speed for design collision scenarios 1 and 2 is 20 km/h

6 Structural passive safety design requirements
6.1 Assessment r
...