Rubber and plastics hoses and hose assemblies - Determination of permeability to gas (ISO 4080:2009)

This part of ISO 8253 specifies relevant test signal characteristics, requirements for free, diffuse, and quasi-free sound fields, and procedures for sound field audiometry using pure tones, frequency-modulated tones or other narrow-band test signals presented by means of one or more loudspeakers. The primary purpose is the determination of hearing threshold levels in the frequency range 125 Hz to 8 000 Hz, but this range can be extended to 20 Hz to 16 000 Hz. This part of ISO 8253 does not include specifications for the use of hand-held loudspeakers. Speech as a test signal is not covered. The purpose of this part of ISO 8253 is to ensure that tests of hearing, using sound field audiometry, give as high a degree of accuracy and reproducibility as possible. Examples of graphical representations of the results are given in Annex A.

Gummi- und Kuntstoffschläuche und -schlauchleitungen - Bestimmung der Gasdurchlässigkeit (ISO 4080:2009)

In dieser Internationalen Norm werden drei Verfahren zur Bestimmung des Gasvolumens festgelegt, das in
einer festgelegten Zeit durch einen Gummi- oder Kunststoffschlauch oder eine Schlauchleitung diffundiert.
Verfahren 1: Bestimmung der Durchlässigkeit für das Prüfgas durch den gesamten Schlauch oder eine
Schlauchlänge mit oder ohne Einlage, mit Ausnahme der Endarmaturen. Die Durchlässigkeit wird bezogen
auf die Länge des Schlauchs mit oder ohne Einlage berechnet.
Verfahren 2: Bestimmung der Durchlässigkeit für das Prüfgas im Übergangsbereich Schlauch/Armatur.
Dieses Verfahren dient zur Bestimmung der Durchlässigkeitskennwerte von Schläuchen mit ungeprickter
Außenschicht, wenn das Gas normalerweise von der textilen Einlage hin zu den abgeschnittenen Enden
austritt. Die Durchlässigkeit wird bezogen auf die Länge des Schlauchs berechnet.
Verfahren 3: Präzise Bestimmung der Durchlässigkeit eines Schlauchs oder einer Schlauchleitung für das
Prüfgas. Die Durchlässigkeit wird bezogen auf die Oberfläche der Schlauchinnenschicht berechnet.
Die Verfahren sind nur mit Prüfgasen anwendbar, die in Wasser nicht löslich sind.
ANMERKUNG 1 Obwohl die Ergebnisse der Verfahren 1 und 2 in den gleichen Einheiten angegeben werden, sind die
für geprickte und ungeprickte Schläuche mit gleichen Anwendungsbereichen ermittelten Ergebnisse nicht unbedingt
vergleichbar, da für die beiden Verfahren unterschiedliche Prüfzeiten festgelegt sind, weswegen von unterschiedlichen
Durchlässigkeiten ausgegangen werden kann.
ANMERKUNG 2 Verfahren 3 ist das zu bevorzugende Verfahren.

Tuyaux et flexibles en caoutchouc et en plastique - Détermination de la perméabilité au gaz (ISO 4080:2009)

L'ISO 4080:2009 spécifie trois méthodes pour la détermination du volume de gaz diffusant à travers un tuyau ou une longueur de tube en caoutchouc ou en plastique pendant une durée déterminée.
Méthode 1: Pour déterminer la perméabilité de l'ensemble d'un tuyau ou d'une longueur de tube, à l'exclusion des raccords d'extrémité, au gaz d'essai. La perméabilité est calculée par rapport à la longueur du tuyau ou du tube.
Méthode 2: Pour déterminer la perméabilité à l'interface tuyau/raccordement. Cette méthode est utilisée pour évaluer les caractéristiques de perméabilité des tuyaux à revêtement non piqueté lorsque le gaz sort de l'armature textile aux extrémités coupées. La perméabilité est calculée par rapport à la longueur du tuyau.
Méthode 3: Pour déterminer précisément la perméabilité d'un tuyau ou d'un flexible au gaz d'essai. La perméabilité est calculée par rapport à l'aire du revêtement du tuyau.
Les méthodes sont applicables uniquement aux gaz qui sont insolubles dans l'eau.

Gumene in polimerne cevi ter cevni priključki - Ugotavljanje prepustnosti za pline (ISO 4080:2009)

Ta del ISO 8253 določa ustrezne lastnosti preskusnega signala, zahteve za prosto, difuzno in skoraj prosto zvočno polje ter postopke za avdiometrijo zvočnega polja z uporabo čistih tonov, frekvenčno moduliranih tonov ali drugih ozkopasovnih preskusnih signalov, ki jih proizvaja eden ali več zvočnikov. Glavni namen je ugotavljanje ravni slušnega praga v frekvenčnem območju med 125 Hz in 8.000 Hz, vendar se lahko razširi na območje med 20 Hz in 16.000 Hz. Ta del ISO 8253 ne vključuje specifikacij za uporabo ročnih zvočnikov. Govor kot preskusni signal ni vključen. Namen tega dela ISO 8253 je zagotoviti, da so preskusi sluha z uporabo avdiometrije z zvočnim poljem čim bolj natančni in ponovljivi. Primeri grafičnih prikazov rezultatov so podani v Dodatku A.

General Information

Status
Withdrawn
Publication Date
19-Jan-2010
Withdrawal Date
07-Jul-2024
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
08-Jul-2024
Due Date
31-Jul-2024
Completion Date
08-Jul-2024

Relations

Buy Standard

Standard
EN ISO 4080:2010
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-februar-2010
1DGRPHãþD
SIST EN ISO 4080:2000
SIST EN ISO 4080:2000/AC:2000
*XPHQHLQSROLPHUQHFHYLWHUFHYQLSULNOMXþNL8JRWDYOMDQMHSUHSXVWQRVWL]DSOLQH
,62
Rubber and plastics hoses and hose assemblies - Determination of permeability to gas
(ISO 4080:2009)
Gummi- und Kuntstoffschläuche und -schlauchleitungen - Bestimmung der
Gasdurchlässigkeit (ISO 4080:2009)
Tuyaux et flexibles en caoutchouc et en plastique - Détermination de la perméabilité au
gaz (ISO 4080:2009)
Ta slovenski standard je istoveten z: EN ISO 4080:2009
ICS:
83.140.40 Gumene cevi Hoses
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 4080
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2009
ICS 23.040.70 Supersedes EN ISO 4080:1995
English Version
Rubber and plastics hoses and hose assemblies - Determination
of permeability to gas (ISO 4080:2009)
Tuyaux et flexibles en caoutchouc et en plastique - Gummi- und Kuntstoffschläuche und -schlauchleitungen -
Détermination de la perméabilité au gaz (ISO 4080:2009) Bestimmung der Gasdurchlässigkeit (ISO 4080:2009)
This European Standard was approved by CEN on 19 September 2009.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4080:2009: E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
This document (EN ISO 4080:2009) has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products" in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses and
hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2010, and conflicting national standards shall be withdrawn at
the latest by June 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 4080:1995.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 4080:2009 has been approved by CEN as a EN ISO 4080:2009 without any modification.

INTERNATIONAL ISO
STANDARD 4080
Fourth edition
2009-12-15
Rubber and plastics hoses and hose
assemblies — Determination of
permeability to gas
Tuyaux et flexibles en caoutchouc et en plastique — Détermination
de la perméabilité au gaz
Reference number
ISO 4080:2009(E)
©
ISO 2009
ISO 4080:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved

ISO 4080:2009(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Test pieces .2
5 Conditioning of test pieces .2
6 Test temperature .2
7 Test gas .2
8 Test pressure .2
9 Apparatus.2
10 Procedure.3
11 Expression of results.6
12 Test report.7

ISO 4080:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 4080 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee
SC 1, Hoses (rubber and plastics).
This fourth edition cancels and replaces the third edition (ISO 4080:1991), which has been technically revised
to clarify the test method procedures and to standardize the units in the expression of results clause for
method 1 and method 2. It also incorporates the Technical Corrigendum ISO 4080:1991/Cor.2:1998.

iv © ISO 2009 – All rights reserved

INTERNATIONAL STANDARD ISO 4080:2009(E)

Rubber and plastics hoses and hose assemblies —
Determination of permeability to gas
WARNING — Persons using this International Standard should be familiar with normal laboratory
practice. This standard does not purport to address all of the safety problems, if any, associated with
its use. It is the responsibility of the user to establish appropriate safety and health practices and to
ensure compliance with any national regulatory conditions.
1 Scope
This International Standard specifies three methods for the determination of the volume of gas diffusing
through a rubber or plastics hose or length of tubing in a specified time.
Method 1: For determining the permeability of the complete hose or length of tubing, excluding end-
fittings, to the test gas. The permeability is calculated with respect to the length of the hose or tubing.
Method 2: For determining the permeability at the hose/fitting interface. This method is used when
determining the permeability characteristics of hoses with an unpricked cover, when the gas usually
issues from the textile reinforcement at the cut ends. The permeability is calculated with respect to the
length of the hose.
Method 3: For determining precisely the permeability of a hose or hose assembly to the test gas. The
permeability is calculated with respect to the surface area of the hose lining.
The methods are applicable only to gases which are insoluble in water.
NOTE 1 Although the results are expressed in the same units for methods 1 and 2, the results obtained will not
necessarily be comparable in the case of unpricked and pricked hoses intended for the same application as the test times
specified are different and the permeability could therefore vary.
NOTE 2 Method 3 is the preferred method.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 8330, Rubber and plastics hoses and hose assemblies — Vocabulary
ISO 23529, Rubber — General procedures for preparing and conditioning test pieces for physical test
methods
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 8330 apply.
ISO 4080:2009(E)
4 Test pieces
4.1 Method 1
The test piece shall be a length of hose or tubing long enough to ensure that the length of the exposed hose
or tubing under the gas-collecting trough is 1 m.
NOTE The cover of a hose test piece may be pricked.
4.2 Method 2
The test piece shall be a length of unpricked hose or tubing fitted with end couplings. It shall have a free
length of 1 m between the couplings.
NOTE The type of coupling used and the method by which the couplings are fixed to the test piece can affect the
results obtained using this method.
4.3 Method 3
The test piece shall be a length of unpricked hose fitted with end couplings. It shall have a free length of 0,5 m
between the couplings.
5 Conditioning of test pieces
No test shall be carried out within 24 h of manufacture. Before testing, the test pieces shall be conditioned, in
accordance with ISO 23529, for at least 3 h at the specified temperature and humidity.
6 Test temperature
Unless otherwise specified in the product standard, the test shall be carried out at a temperature of
23 °C ± 2 °C.
7 Test gas
The test gas shall be as specified in the product standard.
8 Test pressure
Unless otherwise specified in the product standard, the test shall be carried out at a gas pressure of 1 MPa
(10 bar).
9 Apparatus
NOTE Schematic layouts of the test arrangements for the three test methods are shown in Figures 1 to 3.
9.1 Water bath, capable of being maintained at a specified temperature and of sufficient length to
accommodate the test piece.
9.2 Gas supply, provided with a suitable pressure gauge and emergency excess flow shutoff valves in
case of test piece failure.
2 © ISO 2009 – All rights reserved
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.