SIST EN 62580-1:2017

SLOVENSKI STANDARD
01-april-2017
Železniške elektronske naprave - Kabinski multimedijski in telematski podsistemi
za železnice - 1. del: Splošna arhitektura
Electronic railway equipment - On-board multimedia and telematic subsystems for
railways - Part 1: General Architecture
Ta slovenski standard je istoveten z: EN 62580-1:2016
ICS:
33.160.99 Druga avdio, video in Other audio, video and
avdiovizuelna oprema audiovisual equipment
45.060.01 Železniška vozila na splošno Railway rolling stock in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 62580-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2016
ICS 45.060
English Version
Electronic railway equipment - On-board multimedia and
telematic subsystems for railways -
Part 1: General architecture
(IEC 62580-1:2015)
Matériel électronique ferroviaire - Sous-systèmes Elektronische Betriebsmittel für Bahnen - Bordinterne
ferroviaires multimédias et télématiques embarqués - Multimedia- und Telematik-Untersysteme für
Partie 1: Architecture générale Bahnanwendungen -
(IEC 62580-1:2015) Teil 1: Allgemeine Architektur
(IEC 62580-1:2015)
This European Standard was approved by CENELEC on 2015-03-24. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62580-1:2016 E
European foreword
The text of document 9/1990/FDIS, future edition 1 of IEC 62580-1, prepared by IEC/TC 9 "Electrical
equipment and systems for railways" was submitted to the IEC-CENELEC parallel vote and approved
by CENELEC as EN 62580-1:2016.
The following dates are fixed:
(dop) 2017-05-11
• latest date by which the document has to
be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2019-11-11
• latest date by which the national
standards conflicting with the
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive.

For relationship with EU Directive 2008/57/EC amended by Commission Directive 2011/18/EU, see
informative Annex ZZ, which is an integral part of this document.

Endorsement notice
The text of the International Standard IEC 62580-1:2015 was approved by CENELEC as a European
Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu
Publication Year Title EN/HD Year

- - Railway applications - Classification EN 15380-4 -
system for railway vehicles -
Part 4: Function groups
IEC 61375 Series Electronic railway equipment - Train EN 61375 Series
communication network (TCN)
IEC 61375-2-3 -  Electronic railway equipment - Train EN 61375-2-3 -
communication network (TCN) -
Part 2-3: TCN communication profile
IEC/TS 61375-2-4 -  Electronic railway equipment - Train - -
communication network (TCN) -
Part 2-4: TCN Application profile
1) 1)
IEC 61375-2-6 -  Electronic railway equipment - Train EN 61375-2-6 -
communication network -
Part 2-6: Onboard to ground
communication
IEC 62280 -  Railway applications - Communication, - -
signalling and processing systems - Safety
related communication in transmission
systems
ISO/IEC 8824 series Information technology - Abstract Syntax - -
Notation One (ASN.1)
ISO/IEC 8825-1 -  Information technology - ASN.1 encoding - -
rules: Specification of Basic Encoding
Rules (BER), Canonical Encoding Rules
(CER) and Distinguished Encoding Rules
(DER)
ISO/IEC 9646 series Information technology - Open Systems - -
Interconnection - Conformance testing
methodology and framework
ISO/IEC/IEEE 2011 Systems and software engineering - - -
42010 Architecture description

1)
At draft stage.
Annex ZZ
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 2008/57/EC

This European Standard has been prepared under a mandate given to CENELEC by the
European Commission and the European Free Trade Association and within its scope the
standard covers all relevant essential requirements as given in Annex lll of the EC Directive
2008/57/EC (also named as New Approach Directive 2008/57/EC Rail Systems: Interoperability).

Once this standard is cited in the Official Journal of the European Union under that Directive and
has been implemented as a national standard in at least one Member State, compliance with the
clauses of this standard given in Table ZZ.1 relating to ‘rolling stock - locomotives and passenger
rolling stock’ and Table ZZ.2 relating to the ‘telematics applications for passenger services’ of
the rail system in the European Union, confers, within the limits of the scope of this standard, a
presumption of conformity with the corresponding Essential Requirements of that Directive and
associated EFTA regulations.
Table ZZ.1 - Correspondence between this European Standard, the RST LOC&PAS TSI

(published in the Official Journal L 356 on 12 December 2014, p. 228) and Directive 2008/57/EC

Clauses of this Chapter / § / points / Essential Comments
European Standard of RST LOC&PAS TSI Requirements
(ER) of
4.2.5. Passenger- 2. Requirements The TSI does not

related items
specific to each impose any technical
sub-subsystem solution regarding

physical interfaces
2.4. Rolling Stock
4.2.12.2 General
between units.
documentation: -
description of
2.4.2. Reliability
computerised on-
The standard offers a
and availability
board systems
general multi-purpose
The whole standard solution for the digital
2.4.3. Technical
is applicable
communication
compatibility
between applications
and it is relevant to
interoperability.
Table ZZ.2 - Correspondence between this European Standard, the TAP TSI
(published in the Official Journal L 123 on 12 May 2011, p. 11) and Directive
2008/57/EC
Clauses of this Chapter / § / points / Essential Comments
European Standard of TAP TSI Requirements (ER)
of
4.2.21. Networking 2. Requirements

and communication
specific to each sub-
subsystem
4.2.21.1. General
architecture
2.4. Rolling Stock
2.4.2. Reliability and
availability
The whole standard is
applicable
2.4.3. Technical
compatibility
WARNING: Other requirements and other EU Directives may be applicable to the products falling
within the scope of this standard.
IEC 62580-1 ®
Edition 1.0 2015-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Electronic railway equipment – On-board multimedia and telematic subsystems

for railways –
Part 1: General architecture
Matériel électronique ferroviaire – Sous-systèmes ferroviaires multimédias et

télématiques embarqués –
Partie 1: Architecture générale

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 45.060 ISBN 978-2-8322-2225-6

– 2 – IEC 62580-1:2015  IEC 2015
CONTENTS
FOREWORD . 5
INTRODUCTION . 7
1 Scope . 8
2 Normative references . 8
3 Terms, definitions, abbreviations, acronyms, and conventions . 9
3.1 Terms and definitions . 9
3.2 Abbreviations and acronyms . 13
3.3 Conventions . 14
4 Architecture . 14
4.1 General . 14
4.2 Improvements on XML . 16
4.3 Boundary . 17
4.4 OMTS abstract model . 19
4.5 General principles and basic requirements for OMTS services . 22
4.6 OMTS interoperability . 29
5 Use cases . 37
6 Conformity statement . 37
Annex A (informative) OMTS classification . 38
A.1 Identification of On-board Multimedia and Telematic Subsystems and
Services . 38
A.2 OMTS category A: Video surveillance and CCTV services (IEC 62580-2) . 38
A.3 OMTS category B: Driver and crew orientated services . 39
A.4 OMTS category C: Passenger orientated services . 40
A.5 OMTS category D: Train operator and maintainer orientated services . 41
Annex B (informative) FBS, SBS and common structure guidelines . 43
B.1 Introduction . 43
B.2 Functional breakdown structure . 43
B.3 System breakdown structure . 45
B.4 Guidelines common to all service categories . 46
Annex C (informative) Example of formal specification . 47
C.1 Example of formal specification . 47
C.2 Scope . 47
C.3 Requirements . 47
C.4 System Break Down Structure . 47
C.5 Function Break Down Structure . 48
C.6 Description of the abstract model using ASN.1 . 49
Annex D (informative) Use cases . 59
D.1 General . 59
D.2 Use cases of on-board multimedia applications in Japan . 59
D.3 The China locomotive remote monitoring and diagnosis system . 62
D.4 Passenger orientated services – The Italian high speed train Frecciarossa
use case . 64
Annex E (informative) Introduction to ontology . 69
Bibliography . 72

IEC 62580-1:2015  IEC 2015 – 3 –
Figure 1 – OMTS categories and structure of the IEC 62580 series . 7
Figure 2 – Overview of the generic OMTS architecture . 14
Figure 3 – Middleware concept . 17
Figure 4 – Relationship between IEC 61375 and IEC 62580 . 18
Figure 5 – ETB on-board network and board-ground link through MCG-GCG pairs . 19
Figure 6 – Concept of abstract model . 19
Figure 7 – Conceptual model . 20
Figure 8 – Principle of abstract model definition . 21
Figure 9 – Methodology for abstract model definition . 21
Figure 10 – SOA approach . 23
Figure 11 – Clients and devices arrangements . 24
Figure 12 – Service concept . 25
Figure 13 – Block diagram of the service based interface . 26
Figure 14 – Principle of the ontology based Information Exchange Format 2 . 28
Figure 15 – Compatibility map . 28
Figure 16 – Service interfaces . 30
Figure 17 – Subsystem breakdown structure . 31
Figure 18 – Coupling of two consists and related subsystems . 31
Figure 19 – Function mapping and role arbitration . 32
Figure 20 – Function and service mapping on consist network . 32
Figure 21 – Function and service role arbitration . 33
Figure 22 – Uncoupled functional breakdown structure . 34
Figure 23 – Coupled functional breakdown structure . 35
Figure 24 – Service space . 36
Figure 25 – Interaction between on-board services and ground services . 37
Figure C.1 – Display management . 47
Figure C.2 – Display system breakdown structure . 48
Figure C.3 – Display functional breakdown structure . 49
Figure D.1 – Passenger information system structure . 60
Figure D.2 – On board video surveillance system structure . 61
Figure D.3 – Driver Only Operation CCTV System structure . 61
Figure D.4 – China locomotive remote monitoring and diagnosis system structure . 62
Figure D.5 – CMD system structure . 62
Figure D.6 – Data flow of the remote monitoring and diagnosis system . 63
Figure D.7 – Integrated IT network structure . 64
Figure D.8 – Radio mobile cellular network coverage . 65
Figure D.9 – Geometry of the ground cells . 66
Figure D.10 – Mobile network structure . 66
Figure D.11 – Download and upload performance . 67
Figure D.12 – On-board WiFi and UMTS communication . 67
Figure D.13 – On-board back bone and wireless board to ground communication . 68
Figure D.14 – Performance test arrangement . 68
Figure E.1 – Traditional approach . 69

– 4 – IEC 62580-1:2015  IEC 2015
Figure E.2 – Ontology based approach . 69
Figure E.3 – Benefits of ontology based approach . 70
Figure E.4 – Screen shot of Protégé interface . 71

Table 1 – Relationships in the conceptual model. 20
Table B.1 – Example of FBS . 44
Table D.1 – PIS applications in Japan . 60

IEC 62580-1:2015  IEC 2015 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRONIC RAILWAY EQUIPMENT –
ON-BOARD MULTIMEDIA AND TELEMATIC
SUBSYSTEMS FOR RAILWAYS –
Part 1: General architecture
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62580-1 has been prepared by IEC technical committee 9:
Electrical equipment and systems for railways.
The text of this standard is based on the following documents:
FDIS Report on voting
9/1990/FDIS 9/2005/RVD
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of IEC 62580 series, under the general title Electronic railway equipment –
On-board multimedia and telematic subsystems for railways, can be found on the IEC
website.
– 6 – IEC 62580-1:2015  IEC 2015
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
IEC 62580-1:2015  IEC 2015 – 7 –
INTRODUCTION
IEC 62580-1 defines the general architecture of the On-board Multimedia and Telematic
Subsystems (OMTS), so as to achieve compatibility between subsystems in the same vehicle
and between subsystems on-board of different vehicles in the same train.
NOTE 1 The acronym OMTS replaces the previous OMMS (On-board MultiMedia Subsystem) definition, due to a
change in the title of this standard.
The multimedia and telematic system is composed of but not limited to:
A Video surveillance/CCTV
B Driver and crew orientated services
C Passenger orientated services
D Train operator and maintainer orientated services
OMTSs installed in the same vehicle (consist) communicate by means of the consist network.
OMTSs, installed in different vehicle (consist) in the same train, communicate by means of
the train network.
It is likely that each OMTS exchanges information with applications installed on-ground by
means of a wireless communication gateway.
The on-board communication and the on-board to ground communication are specified by the
IEC 61375 series.
NOTE 2 Board-to-ground communication is intended as a generic link, with no assumption on the underlying
technology (radio, satellite or other).
As illustrated in Figure 1, the IEC 62580 series is structured as follows:
IEC 62580-1: General architecture
IEC 62580-2: Video surveillance/CCTV services
Driver and crew orientated services, passenger orientated services and train
operator/maintainer orientated services are matters of standardisation which can be
addressed in the future.
General
architecture
B – Driver and crew
A – Video
orientated services
surveillance/CCTV
D – Train operator and
C – Passenger orientated
maintainer orientated services
services
IEC
Figure 1 – OMTS categories and structure of the IEC 62580 series

– 8 – IEC 62580-1:2015  IEC 2015
ELECTRONIC RAILWAY EQUIPMENT –
ON-BOARD MULTIMEDIA AND TELEMATIC
SUBSYSTEMS FOR RAILWAYS –
Part 1: General architecture
1 Scope
This part of IEC 62580 specifies the general architecture of the On-board Multimedia and
Telematic Subsystem, which includes four categories of multimedia and telematic subsystems
identified as:
A Video surveillance/CCTV
B Driver and crew orientated services
C Passenger orientated services
D Train operator and maintainer orientated services
This part establishes:
• the boundary between the OMTS and the on-board communication system, as described
by the IEC 61375 series
• the methodology to describe an OMTS in terms of abstract model
• the general principles and the basic requirements to specify the services provided/needed
by each category
• the approach to ensure interoperability between services
This part gives guidelines for:
• OMTS classification
• functional breakdown structuring
• system breakdown structuring
• formal specification of an OMTS
This part is applicable to any type of train, e.g. open trains, multiple unit trains and closed
trains.
NOTE The general architecture provides a common basis for the application categories defined in part 2 and
possible future parts of this series of standards. Consequently, the approach is homogeneous for all multimedia
and telematic subsystems addressed by this series of standards.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 61375 (all parts), Electronic railway equipment – Train communication network (TCN)
IEC 61375-2-3, Electronic railway equipment – Train communication network (TCN) – Part 2-
3: TCN communication profile
IEC 62580-1:2015  IEC 2015 – 9 –
IEC 61375-2-4, Electronic railway equipment – Train communication network (TCN) –
Part 2-4: TCN application profile
IEC 61375-2-6, Electronic railway equipment – Train communication network – Part 2-6: On-
board to ground communication
IEC 62280, Railway applications – Communication, signalling and processing systems –
Safety related communication in transmission systems
ISO/IEC 8824 (all parts), Information technology – Abstract Syntax Notation One (ASN.1)
ISO/IEC 8825, Information technology – ASN.1 encoding rules: Specification of Basic
Encoding Rules (BER), Canonical Encoding Rules (CER) and Distinguished Encoding Rules
(DER)
ISO/IEC 9646 (all parts), Information technology – Open Systems Interconnection –
Conformance testing methodology and framework
ISO/IEC 42010:2011, Systems and software engineering – Architecture description
EN15380-4, Railway applications – Classification system for railway vehicles – Part 4:
Function groups
3 Terms, definitions, abbreviations, acronyms, and conventions
3.1 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1.1
communication
capability to transfer information between different parts of a system or subsystem
Note 1 to entry: Communication may refer to on-board, train-ground, train-train or ground-ground transmission.
3.1.2
entity
any concrete or abstract thing of interest
Note 1 to entry: While in general the word entity can be used to refer to anything, in the context of modelling it is
reserved to refer to things in the universe of discourse being modelled (ISO/IEC 10746-2).
3.1.3
function
specific purpose or objective to be accomplished, which can be specified or described without
reference to the physical means of achieving it
Note 1 to entry: A function transfers (considered as a black box) input parameters (material, energy, information)
into aim related output parameters (material, energy, information).
3.1.4
Functional Breakdown Structure
FBS
hierarchical structure summarizing a set of functions leading to the same general focus or
service, organized in function levels
___________
To be published.
– 10 – IEC 62580-1:2015  IEC 2015
3.1.5
function carriers
physical unit of observation to fulfil or partly fulfil one or more required functions
Note 1 to entry: Function carriers are considered as black box while describing the function.
3.1.6
function follower
application process which exchanges messages with the outside world only by means of a
function leader
3.1.7
function leader
application process which manages exchanged messages with the outside world, routing
them appropriately to and from the function follower(s) in a coordinated way
3.1.8
function level
hierarchy level to group functions of equal purpose. The first three levels are defined herein
under:
1st level function
functional domain that encompasses a set of functions related to a same general focus or
service for the considered (rolling stock) system
Note 1 to entry: Example for a 1st level function is:
– Provide appropriate conditions to passengers, train crew and payload.
2nd level function
related to a specific set of activities which contributes to the completion of the functional
domain defined at the first level
Note 1 to entry: Examples for a 2nd level function are:
– Provide proper climate.
– Provide passenger information and entertainment.
Note 2 to entry: At this level, it is not said how a 2nd level function is to be implemented.
Note 3 to entry: A specific 2nd level function often is related to an engineering discipline and might be
supported by one or a minimum number of subsystems.
Note 4 to entry: Each function at level 2 or level 3 has one or several transverse functions as sub-functions.
3rd level function
related to a specific activity within the related set of interconnected activities, it
encompasses a set of tasks
Note 1 to entry: A function at least at level 3 should be supported as much as possible by one single
subsystem.
Note 2 to entry: An example for 3rd level function is:
– Provide and support multimedia for passenger entertainment.
Note 3 to entry: Each function at level 2 or 3 has one or several transverse functions as sub-functions.
3.1.9
model
abstraction or representation of some aspect of a system.

IEC 62580-1:2015  IEC 2015 – 11 –
3.1.10
multimedia
electronic production, coding/decoding, processing, delivery and consuming of information
using a combination of one or more media including video, still images, audio, text in such a
way that can be dynamically updated and/or interactively accessed
3.1.11
ontology
structure of concepts or entities within a domain, organized by relationships; a system model
Note 1 to entry: An ontology is a methodology which allows to specify knowledge within a specific domain in
terms of concepts and the relationships which occur between them, so as to unambiguously define the meaning of
each concept within a certain context. An ontology can be implemented using a semantic formal language which is
machine-interpretable, building a model of the knowledge domain which can be automatically processed by
computers.
3.1.12
operation
all functions which deal with the safety and regular exploitation of the transportation service
Note 1 to entry: Operational services are related to traction, braking and door management.
3.1.13
requirement
necessary condition or ability to constrain the solutions of a task or an aim
Note 1 to entry: A requirement describes for example, performance characteristics, operational conditions and
quality attributes, expressed as measurable and testable technical parameters or indicators.
Note 2 to entry: Requirements are usually summarized in a specification.
Note 3 to entry: Beside requirements allocated to functions there are additional requirements allocated to other
features (e.g. design, manufacturing).
The requirements are classified, but not only, into the following categories:
functional requirement
expresses the requirements on a certain functionality
Note 1 to entry: Functional requirements and use cases come from passenger/pay load and operator
request rather than from integrator and supplier. They express the requirements on a certain functionality
given in the FBS regarding interoperability (with other functions), operation, function/ behaviour, or functional
architecture/design constraints.
The functional designation usually is additionally stated more precisely by detail properties, that provide more
information referring to reliability, availability, performance, quality, documentation, input, output, real-time.
These higher-level functional goals pointed out for ambient conditions, design features and selected target
groups/target objects are “requirements to a function”.
system requirement
requirement on a subsystem or device
Note 1 to entry: Requirement on a subsystem or device regarding the requested technical compatibility,
reliability, availability, maintainability, environmental impact/conditions (recyclables, emissions, EMC, climate,
vibration), LCC, performance, quality, documentation, real-time behaviour, physical limits (dimension,
weight), electrical interface (plugs, voltage, physical layer), or mechanical interface (fixing points, fixing
method).
3.1.14
service
railways perform (transportation) services which are implemented by means of systems and
subsystems
Note 1 to entry: In ICT, a service is a set of one or more functions provided by an application to another one.
Note 2 to entry: A service has some type of underlying computer system that supports the connection offered.

– 12 – IEC 62580-1:2015  IEC 2015
Note 3 to entry: A service provision is based on one or several functions each supported by a system (or
subsystem). A service can also reuse other services. A service provider is able to perform a useful task for a
service consumer, on request of the latter.
Note 4 to entry: The difference between service and function is blurry: in order to have the correct understanding,
the following views are considered: behavioural, structural, external, internal. See Figure 7 for details.
3.1.15
service follower
application process which exchanges messages in a coordinated way with another
application process in a SOA environment
3.1.16
service leader
application process in a SOA environment which manages exchanged messages in a
coordinated way with other service follower(s)
3.1.17
Service Oriented Architecture
SOA
essentially a collection of services. These services communicate with each other. The
communication can involve either simple data passing or it could involve two or more services
coordinating some activity. Some means of connecting services to each other is needed
3.1.18
system
set of components organized to accomplish a specific function or set of functions
3.1.19
System Breakdown Structure
SBS
hierarchy of elements which can represent the structure of a system at different levels of
detail. Structure here means the organisation of relations among the system constituents
3.1.20
subsystem
part of a larger system and set of elements, a coherent and somewhat independent
component of a larger system
Note 1 to entry: A subsystem is a system itself. Therefore, a subsystem can be divided into further subsystems.
Note 2 to entry: A subsystem can be described in terms of functional blocks and interfaces. In a simple case, the
functional blocks only exchange data. Often they need a more complex interaction in terms of services.
Note 3 to entry: A (sub)system is generally defined with a view to achieve a given objective.
3.1.21
telematic
applications which allow to seamlessly use remote objects, information or services, accessing
them by means of a suitable communication system
Note 1 to entry: Telematics is the science of sending, receiving and storing information via telecommunication
devices.
3.1.22
transverse function
function destined for the use together with several level 2 and level 3 functions of the
Functional Breakdown Structure (FBS) at the same time
Note 1 to entry: The transverse functions are not part of the FBS but are implicit, for example ”provide diagnosis”
or “communicate with train bus”.

IEC 62580-1:2015  IEC 2015 – 13 –
3.1.23
Web Services
the most likely connection technology of service-oriented architectures, they essentially use
XML to create a robust connection
3.2 Abbreviations and acronyms
3G Third Generation
ASN.1 Abstract Syntax Notation One
ATP Automatic Train Protection
BD Blue-ray Disk
CCTV Closed Circuit Television
CMD China locomotive remote Monitoring and Diagnosis system
CN Consist Network
CRH China Railway High-speed
DOO Driver Only Operation
DPWS Device Profile for Web Services
DVD Digital Versatile Disk
ECN Ethernet Consist Network
ETB Ethernet Train Backbone
ETBN Ethernet Train Backbone Node
FBS Functional Breakdown Structure
GCG Ground Communication Gateway
GMTS Ground Multimedia and Telematic Subsystem
GPRS General Packet Radio Service
GSM Global System for Mobile Communications
HMI Human Machine Interface
ICT Information and Communication Technology
IEF Information Exchange Format
IT Information Technology
LCD Liquid Cristal Display
LDP Locomotive on-board general Data monitoring
MCG Mobile Communication Gateway
MP3 Moving Picture Expert Group-1/2 Audio Layer 3
NOC Network Operation Centre
OASIS Organization for the Advancement of Structured Information Standards
OMMS On board MultiMedia Subsystem
OMTS On board Multimedia and Telematic Subsystem
OWL Ontology Web Language
PA Public Address
PDA Personal Digital Assistant
PIS Passenger Information System
RDF Resource Description Framework
RM Reference Model
SBS System Breakdown Structure

– 14 – IEC 62580-1:2015  IEC 2015
SOA Service Oriented Architecture
SysML System Modelling Language
TCMS Train Control and Monitoring System
UML Unified Modelling Language
UMTS Universal Mobile Telecommunications System
URI Uniform Resource Identifier
UTC Coordinated Universal Time
WiMAX Worldwide Interoperability for Microwave Access
WLAN Wireless Local Area Network
WS Web Service
WSDL Web Service Description Language
WTB Wired Train Bus
XML eXtensible Mark-up Language
3.3 Conventions
State diagrams are defined following the notation of UML 2.0 state machines.
4 Architecture
4.1 General
Consistently with the scope of this standard (see Clause 1), the General architecture at the
basis of On-board MultiMedia Subsystems (OMTS) is specified in terms of services (see
Figure 2).
IEC 62580-2
OMMS OMMS OMMS OMMS
Category A Category B Category C Category D

Video surveillance/ Driver and crew Passenger Train operator/
IEC 62580
CCTV maintainer
Service Service Service Service
definitions definitions definitions definitions
IEC 62580-1
Service orientated framework
Communication profile
IEC 61375-2-3
IEC 61375
TCN Stack
(ETB − ECN − WTB)
IEC
Figure 2 – Overview of the generic OMTS architecture
The main benefit of the service approach is to decouple applications from communication
aspects, so as to ensure that applications compliant with IEC 62580 series are compatible
with the protocols compliant with IEC 61375 series irrespective of possible amendments of
the two series of standards.
NOTE 1 WTB is not well suitable for supporting a service oriented application interface, due to bandwidth
limitation.
IEC 62580-1:2015  IEC 2015 – 15 –
NOTE 2 Even if this standard is focused on on-board multimedia applications, it is
...