SIST EN 1014-1:2010
(Main)Wood preservatives - Creosote and creosoted timber - Methods of sampling and analysis - Part 1: Procedure for sampling creosote
Wood preservatives - Creosote and creosoted timber - Methods of sampling and analysis - Part 1: Procedure for sampling creosote
This European Standard specifies procedures for obtaining a representative sample from a consignment of creosote. This standard is only applicable to consignments of creosote which are in a single phase at the time of the sampling.
Holzschutzmittel - Kreosot (Teerimprägnieröl) und damit imprägniertes Holz - Probenahme und Analyse - Teil 1: Verfahren zur Probenahme von Kreosot
Dieser Teil der EN 1014 legt Verfahren, repräsentative Proben einer Lieferung von Kreosot (Teerimprägnieröl) zu erhalten, fest.
Dieser Teil der EN 1014 ist nur anwendbar auf Lieferungen von Kreosot, die zum Zeitpunkt der Probenahme als einheitliche Phase vorliegen.
ANMERKUNG 1 Ein Teil des Kreosots kann bei Raumtemperatur in kristalliner Form vorliegen. In solchen Fällen ist es notwendig, das Kreosot vor der Probenahme auf eine Temperatur über dem Kristallisationspunkt zu erwärmen, bei der es vollständig flüssig vorliegt.
ANMERKUNG 2 Das Personal, das mit der Probenahme und Untersuchung beschäftigt ist, sollte bestens mit den Kreosot betreffenden Sicherheitsmaßregeln vertraut sein. Es ist unbedingt notwendig, dass geeignete Sicherheits¬maßnahmen für das Arbeiten mit giftigen und brennbaren Materialien während der Probenahme von Kreosot befolgt werden.
Produits de préservation du bois - Créosote et bois créosoté - Méthodes d'échantillonnage et d'analyse - Partie 1 : Procédure d'échantillonnage de la créosote
La présente norme européenne spécifie des procédures permettant d’obtenir un échantillon représentatif
d’une livraison de créosote.
La présente norme s’applique uniquement aux livraisons de créosote qui ne comportent qu’une seule phase
au moment de l’échantillonnage.
NOTE 1 A température ambiante une partie de la créosote peut être sous sa forme cristalline. Dans ce cas, il est
nécessaire de chauffer la créosote à une température supérieure au point de cristallisation de la créosote en question, à
laquelle elle est complètement liquide avant échantillonnage.
NOTE 2 Il convient d’informer pleinement tout le personnel impliqué dans l’échantillonnage et les essais sur les
mesures de sécurité concernant la créosote. Il est essentiel que des mesures de sécurité appropriées pour la
manipulation de produits dangereux soient suivies lors de l’échantillonnage de la créosote.
Zaščitna sredstva za les - Kreozotno olje in s kreozotnim oljem zaščiten les - Metode vzorčenja in analize - 1. del: Postopek vzorčenja kreozotnega olja
Ta evropski standard določa postopke za pridobivanje reprezentativnega vzorca kreozotnega olja iz pošiljke kreozotnega olja. Ta standard velja le za pošiljke kreozotnega olja, ki so v času vzorčenja v samo eni fazi.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Holzschutzmittel - Kreosot (Teerimprägnieröl) und damit imprägniertes Holz - Probenahme und Analyse - Teil 1: Verfahren zur Probenahme von KreosotProduits de préservation du bois - Créosote et bois créosoté - Méthodes d'échantillonnage et d'analyse - Partie 1 : Procédure d'échantillonnage de la créosoteWood preservatives - Creosote and creosoted timber - Methods of sampling and analysis - Part 1: Procedure for sampling creosote71.100.50Wood-protecting chemicalsICS:Ta slovenski standard je istoveten z:EN 1014-1:2010SIST EN 1014-1:2010en,fr,de01-oktober-2010SIST EN 1014-1:2010SLOVENSKI
STANDARDSIST EN 1014-1:20041DGRPHãþD
SIST EN 1014-1:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1014-1
June 2010 ICS 71.100.50 Supersedes EN 1014-1:1995English Version
Wood preservatives - Creosote and creosoted timber - Methods of sampling and analysis - Part 1: Procedure for sampling creosote
Produits de préservation du bois - Créosote et bois créosoté - Méthodes d'échantillonnage et d'analyse -Partie 1: Procédure d'échantillonnage de la créosote
Holzschutzmittel - Kreosot (Teerimprägnieröl) und damit imprägniertes Holz - Probenahme und Analyse - Teil 1: Verfahren zur Probenahme von Kreosot This European Standard was approved by CEN on 12 May 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1014-1:2010: ESIST EN 1014-1:2010
EN 1014-1:2010 (E) 2 Contents Page Foreword .31Scope .42Terms and definitions .43Sampling flowing creosote from a pipeline by means of a probe .43.1Apparatus .43.2Procedure .54Sampling from a tank having a uniform horizontal cross section throughout its depth .54.1Apparatus .54.2Procedure .55Sampling from a horizontal cylindrical tank .65.1Apparatus .65.2Procedure .66Sampling report .7 SIST EN 1014-1:2010
EN 1014-1:2010 (E) 3 Foreword This document (EN 1014-1:2010) has been prepared by Technical Committee CEN/TC 38 “Durability of wood and wood-based products”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2010, and conflicting national standards shall be withdrawn at the latest by December 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1014-1:1995. This standard forms part of a series of standards relating to the sampling and analysis of creosote and creosoted timber. The other standards of the series are: EN 1014-2, Wood preservatives
Creosote and creosoted timber
Methods of sampling and analysis
Part 2: Procedure for obtaining a sample of creosote from creosoted timber for subsequent analysis EN 1014-3, Wood preservatives
Creosote and creosoted timber
Methods of sampling and analysis
Part 3: Determination of the benzo(a)pyrene content of creosote EN 1014-4, Wood preservatives
Creosote and creosoted timber
Methods of sampling and analysis
Part 4: Determination of the water-extractable phenols content of creosote According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
SIST EN 1014-1:2010
EN 1014-1:2010 (E) 4 1 Scope This European Standard specifies procedures for obtaining a representative sample from a consignment of creosote. This standard is only applicable to consignments of creosote which are in a single phase at the time of the sampling. NOTE 1 At ambient temperature, part of the creosote may be in crystalline form. In such cases, it is necessary to heat the creosote to a temperature above the crystallization point of the particular creosote at which it is entirely liquid before sampling. NOTE 2 All personnel concerned with sampling and testing should be fully acquainted with the safety precautions relating to creosote. It is essential that proper safety measures for handling hazardous materials are followed when sampling creosote. 2 Terms and definitions For the purposes of this document, the following terms and definitions apply. 2.1 consignment quantity of material covered by a particular consignment note or shipping document 2.2 crystallization point temperature at which crystal formation starts in the creosote oil 2.3 sample one or more sampling units taken from a larger number of sampling units, or one or more increments taken from a sampling unit 2.4 laboratory sample sample as prepared for sending to the laboratory and intended for inspection or testing 3 Sampling flowing creosote from a pipeline by means of a probe 3.1 Apparatus 3.1.1 Sampling probe consisting of a pipe of about 12 mm bore with a valve, fitted into the side of the pipeline on the discharge side of the pump and preferably in a rising section of the pipeline.
The pipe extends into the centre of the pipeline, with its inner end bevelled at 45° or its inner end bent at 90° and extended for a very short distance, in both cases the orifice faces upstream. NOTE A suitable desig
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.