SIST ISO 10763:2021

SLOVENSKI STANDARD
01-julij-2021
Fluidna tehnika - Hidravlika - Cevi iz celega in varjene natančne jeklene cevi z
ravnimi konci - Mere in nazivni delovni tlaki
Hydraulic fluid power -- Plain-end, seamless and welded precision steel tubes --
Dimensions and nominal working pressures
Transmissions hydrauliques -- Tubes de précision en acier, soudés ou non, à extrémités
lisses -- Dimensions et pressions nominales de travail
Ta slovenski standard je istoveten z: ISO 10763:2020
ICS:
23.100.40 Cevna napeljava in sklopke Piping and couplings
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERNATIONAL ISO
STANDARD 10763
Third edition
2020-06
Hydraulic fluid power — Plain-end,
seamless and welded precision steel
tubes — Dimensions and nominal
working pressures
Transmissions hydrauliques — Tubes de précision en acier, soudés ou
non, à extrémités lisses — Dimensions et pressions nominales de travail
Reference number
©
ISO 2020
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 1
5 Nominal working pressures . 1
6 Identification statement (reference to this document) . 3
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee
SC 4, Connectors and similar products and components.
This third edition cancels and replaces the second edition (ISO 10763:2019), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— A sentence was corrected in the Scope.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved

Introduction
In hydraulic fluid power systems, power is tran
...